Separation and recovery of metallic zinc and iron concentrate from blast furnace dust by vacuum carbothermal reduction
Xue Deng,Run Huang,Xiaodong Lv,Jingpiao Yang,Jing Yang
DOI: https://doi.org/10.1016/j.psep.2022.04.050
IF: 7.8
2022-06-01
Process Safety and Environmental Protection
Abstract:Theoretical calculations and experimental studies were used to investigate a process involving the evaporation, condensation, and separation of blast furnace dust with vacuum carbothermal reduction. The theoretical calculations revealed that the removal rate of metallic zinc from blast furnace dust by vacuum carbothermal reduction was> 99.6%, with a 800–900 °C reduction temperature range. The experimental results showed a 97.8% removal rate of metallic zinc in the reduced sample. The phase transformations of iron and zinc during the reduction process were ZnFe2O4 → Fe2O3 → Fe3O4 → FeO and ZnFe2O4 → ZnO → Zn(g), respectively. Metallic zinc in ZnFe2O4 phase was reduced, condensed, and collected after escaping in the gas form. These results demonstrated the feasibility of a novel process for recovering metallic zinc and high-grade iron-bearing raw materials from blast furnace dust.Solar-powered desalination is a cost-effective technology to produce drinkable, potable water using energy from the sun. However, its use in domestic and industrial applications is minimal because of its low daily production. This study produced a novel nanoporous Cr-Mn-Fe oxide nanocoating by modulable chemical oxidation at a temperature of around 90 ℃ in an acidic mixture of 21–34 wt% conc.H2SO4, 37.5–53 wt% distilled water & 15–30 wt% sodium dichromate salt on a mirror-polished SS202 sheet to act as a basin liner for the nanocoated solar still (NCSS). The optical characterization of nanostructure coating was done using Cary 5000 spectrophotometer and FTIR spectrophotometer for absorptivity (90%) and emissivity (14.4% at 300 ℃), respectively. It was found that the nanocoated solar still (NCSS) produced 36.36%, 28.62%, and 26.27% more distillate yield when compared with conventional solar still (CSS) for 1 cm, 2 cm, and 3 cm depth of water, respectively. Enviro-economic studies, energy matrices evaluation, and water quality analysis were performed to compute greenhouse gases emissions, carbon dioxide mitigation, carbon credit gained, energy-payback time (EPT), energy production factor (EPF), life cycle conversion efficiency (LCCE), and suitability of distilled water for drinking. The cost per liter (CPL) of desalinated water for NCSS was inferred to be 15.6% more economical than for a CSS and 81% more economical than packaged drinking water in India.The disadvantages of the air–cathode single-chamber microbial fuel cell (AC-SCMFC) performance can be caused by numerous factors, and retention time (RT) is one such factor. It is difficult to conclude the ideal RT run for the specific tests under the same conditions. To determine the optimum RT for various types of microbial fuel cell (MFC), an AC-SCMFC batch-mode reactor was carried out by comparing different types and concentrations of substrates based on the main parameters of organic removal and power generation. The AC-SCMFC reactor was designed for the effective working volume of 500 mL and operated for 52 d in batch mode with factors being significantly correlated with the performance of the MFC reactor, which were two different substrates, sucrose and acetate, and three different chemical oxygen demand (COD) levels of 400; 1000, and 2500 mg/L (low, medium, and high, respectively) equipped with two graphene nanoplatelets (GNPs)-based electrodes connected to 100 Ω resistance and plugged onto a data logger. The results of this study indicated a significant pattern at the medium level, at which the optimum RT of sucrose was achieved at 24 h and that of acetate at 48 h. In comparison, the performances pattern at low and high levels of both substrates was insignificant to determine the optimum RT. For further application, the recommended RT for both substrates at any concentration is 24 h due to high overall performance, and the optimum RT established in this study could be applied to all types of MFC research, particularly in oxidizable or biodegradable organic ranges, which ensures high performance.Incineration is a harmless way to treat municipal sludge. However, it is difficult to fix heavy metals in the sludge-incinerated ash (SIA). To fix the heavy metals and recycle the SIA effectively, this work innovatively proposed the SIA as skeleton material, and five shape-stable phase change composites (SSPCCs) with different mass ratios of SIA to NaNO3 (phase change material, PCM) were fabricated via the cold-compression & hot-sintering (CCHS) method. Then, key thermal performance, mechanical strength, and micromorphology were investigated while the chemical compatibility between the SIA components and NaNO3 was analyzed. Results showed that the SSPCCs could fix the heavy me -Abstract Truncated-
engineering, environmental, chemical