Abstract:Abstract This paper presents the computational methodology and experimental investigations accomplished to enhance the efficiency of a turbine stage by applying non-axisymmetric profiling on the rotor hub wall. The experimental setup was a two-stage axial turbine, which was tested at “LISA” test facility at ETH Zurich. The first stage was considered to create the flow history for the second stage, which was the target of the optimization. The hub cavity of the second stage was designed with large dimensions as a requirement of a steam turbine. The goal was to optimize the interaction of the cavity leakage flow with the rotor passage flow to reduce the losses and increase efficiency. The computational optimization was completed using a genetic algorithm coupled with an artificial neural network on the second stage of the test turbine. Unsteady time-accurate simulations were performed using in-house developed “MULTI3” solver. Besides implementing all geometrical details (such as hub and tip cavities and fully 3D blade geometries) from the experimental setup into the computational model, it was learned that the unsteady upstream effect could not be neglected. A novel approach was introduced using unsteady inlet boundary conditions to consider the multistage effect while reducing the computational cost to half. The importance of this implementation was tested by performing a steady simulation on the optimized geometry. The predicted efficiency gain from steady simulations was 4.5 times smaller (and negligible) compared to the unsteady approach. Excluding the cavity geometry was also assessed in a different simulation setup showing 3.9% over-prediction in the absolute efficiency value. Comprehensive steady and unsteady measurements were performed utilizing pneumatic, fast response aerodynamic probe (FRAP), and fast response entropy probe (FENT) on the baseline and profiled test cases. The end wall profiling was found to be successful in weakening the strength of the hub passage vortex by a 19% reduction in the under-over turning. As a result, the blockage was reduced near the hub region leading to more uniform mass flow distribution along the span. The flow angle deviations at the higher span position were also corrected due to better control of the flow angles. Furthermore, the improvements were confirmed by reductions in entropy, secondary kinetic energy, and pressure unsteadiness. The accurate computational implementations led to an excellent agreement between the predicted and measured efficiency gain.

Optimization of Impeller Parameters for Hydrodynamic Turbine Based on Multi-Objective Orthogonal Test Design

Pressure Pulsation and Radial Force Characteristics of Dual-Side Impellers for the Turbine Energy Recovery Integrated Machine

Optimization method investigation for centrifugal pump performance based on 3D inviscid inverse design

Optimization of a Centrifugal Impeller on Blade Thickness Distribution to Reduce Hydro-Induced Vibration

Multidisciplinary Design Optimization of Twin-Web Turbine Disk with Pin Fins in Inner Cavity

Multidisciplinary Design and Multi-Objective Optimization on Guide Fins of Twin-Web Disk Using Kriging Surrogate Model

Fluid-Thermal-Structural Analysis of Partial Admission Axial Impulse Turbines with Liquid Jet Impingement Cooling

A Study and Optimization of the Unsteady Flow Characteristics in the Last Stage Impeller of a Small-Scale Multi-Stage Hydraulic Turbine

Characterization of Loss, Temperature, and Stress on Partial Admission Axial Impulse Turbines with Liquid Jet Impingement Cooling

Unsteady Steam Turbine Optimization Using High-Fidelity Computational Fluid Dynamics

Numerical Analysis of the Influence of Design Parameters on the Efficiency of an OWC Axial Impulse Turbine for Wave Energy Conversion

Multi-parameter Optimization Design, Numerical Simulation and Performance Test of Mixed-Flow Pump Impeller

Optimization Design of a Reversible Pump–turbine Runner with High Efficiency and Stability

Parametric design and multi-objective optimization on blade high-pressure side of a pump-turbine

Multiobjective Optimization Design Of A Pump-Turbine Impeller Based On An Inverse Design Using A Combination Optimization Strategy

Multi-objective optimization of aerodynamic and erosion resistance performances of a high-pressure turbine

Aerothermodynamic Design and Numerical Simulation of Radial Inflow Turbine Impeller for A 100kw Microturbine

Numerical Analysis of Non-Axisymmetric Flow Characteristic for a Pump-Turbine Impeller at Pump Off-Design Condition

Hydraulic Optimization and Performance Analysis of High Rotating Speed Pump As Turbine

A cooled turbine blade design and optimization method considering the cooling structure influence

Aero-mechanical multidisciplinary optimization of a high speed centrifugal impeller