Abstract:Li-ion batteries (LiBs) are widely adopted in electric vehicles (EVs) owing to their superior properties, such as high energy density, low discharge rate, long lifespan, and lightweight construction. Since the battery pack is the sole energy source for an EV, its performance is critical for optimal vehicle operation. However, the battery's calendar life, cycle life, and overall performance are significantly affected by temperature variations. The Li-ion batteries used in EVs may encounter challenging working conditions, leading to thermal problems such as significant capacity and power loss. In contrast, thermal runaways can occur at temperatures above a specific threshold, leading to severe health deterioration and sometimes catastrophic safety hazards such as fires and explosions. As the temperature significantly impacts Li-ion batteries, a battery thermal management system that can efficiently dissipate heat is crucial to ensure the battery's optimal performance and longevity. Hence, it is crucial to develop accurate algorithms for battery thermal management systems to precisely and dynamically estimate the temperature dynamics of the batteries integrated within the battery pack. While experimental data can be used to estimate battery temperatures, the dynamic and diverse operating conditions of electric vehicles (EVs) present a significant challenge. Therefore, accurately predicting thermal response within batteries is critical. Various thermal models have been developed to predict the thermal behavior of batteries and quantify the amount of heat generated. The simplified thermal model only considers joule heating and reversible entropic heating. However, more accurate physics-based models consider reversible heat caused by the side reactions, heat generated by mass transport loss, and even mixing-induced heat. The amount of heat generated inside a Li-ion battery is determined by its equivalent internal resistance, open circuit voltage, and entropy change, which are in turn influenced by temperature and depth of discharge (DoD). To the best of the authors' knowledge, previous research on the heat generation of Li-ion batteries has been limited in some respects. Specifically, there has been little investigation into the combined impact of temperature and depth of discharge (DoD) across a wide temperature range. Most studies have been conducted under ambient temperature conditions, and only a few have focused on high temperatures within a narrow range with low discharge rates. Thus, this study aims to address the research gap regarding the impact of temperature and depth of discharge (DoD) on heat generation in Li-ion batteries by analyzing these parameters using a transient battery thermal model. The research intends to improve the accuracy and precision of battery thermal behavior prediction, which has broad implications for battery-powered applications. This study aims to evaluate the impact of different resistance models on heat generation in Li-ion batteries, explicitly comparing a constant resistance model with a model that considers resistance as a function of temperature and depth of discharge (DoD). Investigating the interdependent impact of battery temperature and DoD on heat generation is crucial to create an accurate battery thermal model with high fidelity. The current study uses a two-dimensional battery thermal model to comprehensively analyze thermal behavior of a LiFePO 4 -20Ah Li-ion pouch cell. In this research study, heat generation in a Li-ion battery is evaluated by estimating the internal resistance and entropic change obtained from experimentation. The energy equation is then solved using the finite difference method in MATLAB to obtain the transient thermal response of the battery. The developed transient electrothermal model is validated against experimental data under varying C rates to assess the accuracy and precision of the proposed model. The simulation results show that the thermal response obtained considering the effect of temperature and DoD on heat generation shows more accurate results than the constant resistance values. The thermal behavior of a LiFePO 4 pouch cell, considering constant values for heat generation, has a maximum relative error of roughly 19.99% compared to experimental data at a 4C discharge rate. While this maximum relative error was reduced to 6.29% when considering the effect of temperature and DoD on heat generation. In the constant resistance model, more significant errors can be attributed to the fact that the resistance of a Li-ion battery varies with the depth of discharge (DoD). While the initial discharge phase of the battery exhibits minimal changes in resistance values, a substantial increase in resistance occurs during the final stages of discharge. This contrasts with the actual behavior of Li-ion batteries, which demonstrate significant variations in resistance values throughout the discharge process. Thus, coupling the effects of DoD and temperature on heat generation is necessary to accurately predict the thermal behavior of Li-ion battery. Figure 1

Identification of Temperature-Dependent Gas Production Rates in Pouch Lithium-Ion Cells

Degradation Diagnosis of Lithium-Ion Batteries Considering Internal Gas Evolution

Study on the thermal interaction and heat dissipation of cylindrical Lithium-Ion Battery cells

A device for real-time detection of gas generated from commercial lithium-ion cell

Non-uniform heat generation model of pouch lithium-ion battery based on regional heat generation rate

Quantifying the Effects of Temperature and Depth of Discharge on Li-Ion Battery Heat Generation: An Assessment of Resistance Models for Accurate Thermal Behavior Prediction

A Simplified Mathematical Modeling Approach for Thermal Runaway of Li(Ni0.8Co0.1Mn0.1)O2 Pouch Cells Based on Thermal Runaway Experimental Data

State-of-charge estimation of lithium-ion batteries from a gas-liquid dynamics model including the direct temperature input

Three‐dimensional layered electrochemical‐thermal model for a lithium‐ion pouch cell

An Automatic Identification Method of Thermal Physical Parameter for Lithium-Ion Batteries Suffering from Thermal Runaway

Impact of solid-electrolyte interphase layer thickness on lithium-ion battery cell surface temperature

Full‐Dimensional Analysis of Gaseous Products Within Li‐Ion Batteries by On‐Line GC‐BID/MS

Developing an electro-thermal model to determine heat generation and thermal properties in a lithium-ion battery

An Experimental Study on Thermal Runaway Behavior for High-Capacity Li(Ni0.8Co0.1Mn0.1)O2 Pouch Cells at Different State of Charges

Thermo-Electro-Mechanical Modeling and Experimental Validation of Thickness Change of a Lithium-Ion Pouch Cell with Blend Positive Electrode

Thermal Design For The Pouch-Type Large-Format Lithium-Ion Batteries I. Thermo-Electrical Modeling And Origins Of Temperature Non-Uniformity

Multiphysics-informed thermal runaway model for estimating the pressure evolution induced by the gas formation in a lithium-ion battery

Methods–Temperature-Dependent Gassing Analysis by On-Line Electrochemical Mass Spectrometry of Lithium-Ion Battery Cells with Commercial Electrolytes

Characteristic Prediction and Temperature-Control Strategy under Constant Power Conditions for Lithium-Ion Batteries

A Standardised Potentiometric Method for the Effective Parameterisation of Reversible Heating in a Lithium-Ion Cell

Simulating the Electrochemical-Thermal Behavior of a Prismatic Lithium-Ion Battery on the Market under Various Discharge Cycles