Abstract:Corner separation is a universal flow phenomenon in a compressor. It contributes greatly to loss and passage blockage in the compressor stage. In order to mitigate the corner separation and improve the performance of compressor cascade, a new flow control method, a microblade installed on the endwall upstream of the separation onset location, was proposed on the basis of the comprehension of the flow field characteristics on the juncture of the endwall and blade region. A numerical investigation was performed in an annular compressor cascade to assess the effectiveness of micro-blade. The results show that the cascade aerodynamic performance under incidence from +2.2° to +10° is improved after a micro-blade installed, and the decrease of total pressure loss coefficient and the increase of static pressure rise was achieved. Furthermore, the blockage of the cascade is restrained and flow deflection angle increased. To understand the flow physics of the underlying mechanism of micro-blade, detailed analysis of predicted flow field was carried out. It indicates that a local high static pressure region which is resulted from the concave curvature of the micro-blade pressure surface appeared on the suction surface to accelerate flow upstream of separation onset location. The acceleration of flow produced a jet to reduce the thickness of boundary layer on the suction surface. Also, the jet can build a “jet barrier” near the endwall to hinder the accumulation of low momentum flow transported by passage cross flow. INTRODUCTION Corner separation is an inherent flow feature in the junction of the suction surface and endwall of axial compressors (Gbadebo, 2005). From former researches, this kind of three-dimensional separation can lead to blockage and loss from downstream mixing which has negative effects on stability and efficiency of axial compressors (Dring, 1982; Joslyn, 1985; Choi, 2006; Yamada, 2016). With stage loading of axial compressors increasing, the corresponding increase of cross passage pressure gradient and streamwise adverse pressure gradient is unavoidable. Therefore, corner separation gradually becomes one of the most essential limiting factors on high-loaded axial compressor performance and operability. In order to control the negative effects due to corner separation and to improve the performance of high-loaded compressor, many active and passive flow control methods have been proposed. Concerning development of active flow control method, a number of studies show that the active flow control methods, such as boundary layer suction (Peacock, 1965), boundary layer jet (Nerger, 2010), vortex generator jet (Feng, 2015) as well as plasma actuation(Li, 2010), have capacity to suppress corner separation. Due to complexity of actuation system and requirement of energy input, these flow control methods were not pursued for practical application. Compared with active flow control, passive flow control methods can be achieved easily by device with relatively simple configuration and don’t require any external energy

Combined Control Method and Mechanism Analysis for Corner Separation in a Compressor Cascade

Large Eddy Simulation and Combined Control of Corner Separation in a Compressor Cascade

Effect on corner separation control for high load compressor cascade with different end-wall BLS position

Combined Flow Control Strategy Investigation for Corner Separation and Mid-Span Boundary Layer Separation in a High-Turning Compressor Cascade

Research progress of corner separation in axial-flow compressor

Corner Stall Control in Linear Compressor Cascade by Blended Blade and Endwall Technique Based on Large Eddy Simulation

Numerical Investigation of Passive Corner Separation Control Using a Micro-blade in an Annular Compressor Cascade

Experimental and Numerical Research on Blended Blade and End Wall Technique in a Compressor Cascade

Passive flow control of the corner separation in an annular compressor cascade with a micro-blade

Experimental Study and Vortex Analysis in A Linear Compressor Cascade with Active Flow Control

Research on Corner Separation Control for Compressor Cascade with End-Wall Jet Flow

PIV investigation on corner separation control in a compressor cascade based on a vortex generator

Corner Separation Control by Boundary Layer Suction Applied to a Highly Loaded Axial Compressor Cascade

An Evaluation Strategy of Control Method for Corner Separation/Stall in Compressor Cascades

Numerical Investigation on Corner Separation Control in a Linear Compressor Cascade by Synthetic Jet

Unsteady Flow Mechanism of Corner Separation Control Using Blade End Slots in a Highly Loaded Compressor Cascade

Passive Separation Control with Blade-End Slots in a Highly Loaded Compressor Cascade

Experimental and numerical investigation of two blended blade and endwall configurations

Experimental and Numerical Investigation on the Aerodynamic Performance of a Compressor Cascade Using Blended Blade and End Wall

Investigation of Control Effects of End-Wall Self-Adaptive Jet on Three-Dimensional Corner Separation of a Highly Loaded Compressor Cascade

Full blended blade and endwall design of a compressor cascade