Abstract:Surface scratches and residual stresses inevitably appear on the surface of the component as a result of the machining process. The damage evolution of surface scratch due to the combined effect of cyclic loading and residual stresses will be significantly different from the case where only the cyclic loading is considered. In the damage evolution of surface scratch, the short crack growth is of great importance owing to its apparently anomalous behaviors compared with the long crack growth. In this paper, the effect of the surface roughness and the residual stress on the short crack growth is studied. Firstly, the surface roughness and the residual stress of 7075-T6 aluminum alloy induced by the high speed milling process with various cutting speeds and feed rates are investigated with the experimental method. The maximum height roughness parameter is measured, which is regarded as the surface defect induced by the milling process. The residual stress on the specimen surface is measured with the X-ray diffraction. Results show that the surface roughness becomes higher with the increase of the feed rate. However, the influence of the cutting speed on the surface roughness is not significant. The residual stresses on the specimen surface are all in the compressive state. The residual stress is more compressive as the feed rate increases. The effects of the process parameters on the surface roughness and the residual stress are described by the fitted formulas. Then a modified model is built to characterize short fatigue crack growth behaviors with the consideration of the residual stress. This model is proved to provide a realistic treatment of the short crack growth, as reflected by comparison with experimental fatigue crack growth data of medium carbon steel and 7075-T6 aluminum alloy published in literature. The effect of surface roughness and residual stress caused by the milling process on the short crack growth is also investigated by using the proposed model. The growth of the scratch is nonlinear when it is subjected to the cyclic load. The compressive residual stress reduces the growth rate of the crack. The crack with larger initial surface roughness grows faster than that with smaller roughness. The correlation of surface roughness, residual stress and crack growth length is obtained by the polynomial fitting. The investigations in this paper can help the damage tolerance design of structures and improve the awareness of the effect of the residual stress and surface roughness induced by the machining process on the short crack growth.

Mechanism of Initiation and Propagation of Surface Cracks in Gun Bore under Thermomechanical Coupling Impact

TWO TYPES OF CRACKS ON CAVITY SURFACE OF HIGH-LOADED SOLID PROPELLANT GRAIN

Finite element analysis of the friction and wear of the barrel bore during the projectile extrusion

3D J-Integral Finite Element Model of Inner Surface Cracks in a Certain Gun Barrel Based on MARC

Analysis on interfacial debond crack of SRM

Experimental Investigation Of Crack/Debond Propagation Process In Burning Test Motor

Analyzing barrel surface damage in failed large caliber cannons

Interface Crack Behavior of Thermal Protection Coating of Gun Bores under Transient Convective Cooling

Numerical Simulation of Surface Crack Propagation in Thermal Barrier Coatings Under Thermal Mismatch Stress

Analysis of the Surface Cracks of Long Range Storage Solid Motor Grain

Study on interior ballistic characteristics of worn gun considering projectile engraving process

Thermo-mechanical analysis of strength degradation of 30SiMn2MoVA gun barrel material during continuous shooting

Research on the Erosion of Gun Barrel Based on Vented Vessel Tests

Strain Hardening and Strain-Rate Effect in Friction Between Projectile and Barrel During Engraving Process

A FRACTURE MODEL OF GRAIN AND NUMERICAL CALCULATION FOR HIGH PRESSURE GUN

The Construction of a Small-Caliber Barrel Wear Model and a Study of the Barrel Wear Rule

Peridynamic simulation for the laser ignition model of energetic material with cracks

A comparative study on gunpowder erosion and promoted ignition combustion of 30SiMn2MoV gun barrel

Effect of Crack Propagation on Surface Formation Mechanism and Surface Morphology Evaluation of Longitudinal–torsional Composite Ultrasonic Mill Grinding of Si3N4

Effect of Surface Roughness and Residual Stress Induced by High Speed Milling Process on Short Crack Growth

Theoretical and numerical research on the dynamic launch response of carbon fiber composite cartridges