Collinear Raman Amplifier Based on Diamond

Hao Zheng,Xin Hao,Boyuan Zhan,Xiaoyu Chan,Hui Chen,Yulei Wang,Zhenxu Bai,Zhiwei Lu

DOI: https://doi.org/10.1109/cleo-pr60912.2024.10676430

2024-01-01

Abstract:Utilizing a 1064 nm laser with a single pulse energy of 6 mJ as the pump, we demonstrated a 1240 nm first-order Stokes energy output of 4.2 mJ through a diamond Raman amplifier. This corresponds to a peak power of up to 37.5 kW. © 2024 The Author(s).

What problem does this paper attempt to address?

High-power dual-wavelength intracavity diamond Raman laser

Hui Chen,Yufan Cui,Xiaowei Li,Boyuan Zhang,Yunpeng Cai,Jie Ding,Yaoyao Qi,Bingzheng Yan,Yulei Wang,Zhiwei Lu,Zhenxu Bai

DOI: https://doi.org/10.1080/26941112.2023.2282527

2023-12-04

Functional Diamond

Abstract:Diamond crystals have garnered significant attention for applications in photonics, owing to their characteristics of ultra-high thermal conductivity, extremely broad spectral transmission range, and high Raman gain coefficient. These characteristics are particularly advantageous for the development of high-power, multi-wavelength lasers. In this work, we utilize single crystal diamond as a Raman gain medium, for intracavity wavelength-conversion of emission from a side-pumped, electro-optically Q-switched Nd:YAG module. Cascaded Raman conversion is demonstrated and dual-wavelength, pulsed laser emission at wavelengths of 1.2 μm (first-Stokes wavelength) and 1.5 μm (second-Stokes wavelength) is achieved (with a maximum combined pulse energy of 6.19 mJ). The relative ratio of output energy at the two Stokes orders could be varied by tuning the characteristics of the output coupling mirror and the length of the laser resonator. When operating at maximum pump power, the pulse width of the second-Stokes field was approximately half that of the first-Stokes field (second-Stokes ∼10 ns, first-Stokes ∼18 ns), resulting in maximum peak powers of 174 kW (at 1.2 μm) and 220 kW (at 1.5 μm). To the best of our knowledge, this is the highest reported peak power generated from a dual-wavelength, intracavity diamond Raman laser. This work highlights the diversity and utility of diamond as an effective wavelength-conversion component in high-power lasers, and stands as the current state-of-the-art in high pulse-energy, high peak-power, multi-wavelength intracavity Raman lasers.
On-Chip Diamond Raman Laser

Pawel Latawiec,Vivek Venkataraman,Michael J. Burek,Birgit J. M. Hausmann,Irfan Bulu,Marko Loncar

DOI: https://doi.org/10.1364/OPTICA.2.000924

2015-09-02

Abstract:Synthetic single-crystal diamond has recently emerged as a promising platform for Raman lasers at exotic wavelengths due to its giant Raman shift, large transparency window and excellent thermal properties yielding a greatly enhanced figure-of-merit compared to conventional materials. To date, diamond Raman lasers have been realized using bulk plates placed inside macroscopic cavities, requiring careful alignment and resulting in high threshold powers (~W-kW). Here we demonstrate an on-chip Raman laser based on fully-integrated, high quality-factor, diamond racetrack micro-resonators embedded in silica. Pumping at telecom wavelengths, we show Stokes output discretely tunable over a ~100nm bandwidth around 2-{\mu}m with output powers >250 {\mu}W, extending the functionality of diamond Raman lasers to an interesting wavelength range at the edge of the mid-infrared spectrum. Continuous-wave operation with only ~85 mW pump threshold power in the feeding waveguide is demonstrated along with continuous, mode-hop-free tuning over ~7.5 GHz in a compact, integrated-optics platform.

Optics
Investigation of the Pulse Characteristics of an Injection Seeded Diamond Raman Amplifier

Hao Zheng,Zhenxu Bai,Xin Hao,Jie Ding,Yaoyao Qi,Bingzheng Yan,Yulei Wang,Zhiwei Lu

DOI: https://doi.org/10.1063/5.0232346

IF: 4

2024-01-01

Applied Physics Letters

Abstract:Raman amplification is a highly efficient means by which amplification of laser radiation and beam clean-up can be achieved. Although this process has been described in the literature, little attention has been given to the investigation of pulse characteristics of the laser fields involved in the process. In this work, we analyze the evolution of the fundamental and Stokes fields involved in the Raman amplification process, with a focus on Stokes extraction efficiency within a diamond Raman amplifier. This work offers insight into the means by which the Raman amplification process can be optimized/maximized for a given set of laser fields. Experimental observations show that depletion of the fundamental field occurs during the amplification process, causing an initially Gaussian pulse shape to become increasingly concave. The rate at which the pulse peak diminishes and the overall shape becomes concave is correlated with the rate of amplification of the Stokes field pulse intensity. This experimental observation is supported by theoretical modeling using rate equations wherein Raman amplification under different initial conditions is numerically simulated, and the energy extraction efficiency and pulse shapes under different intensities are analyzed. Experimentally, the amplified laser output of the Stokes field from this system is 4.2 mJ (equivalent to a peak power of up to 37.5 kW), and an amplification efficiency of 18% is achieved.
Order Controllable Multi-Wavelength Laser Utilizing Cascaded Diamond Raman Conversion

Jie Ding,Feng Gao,Yunpeng Cai,Zhenxu Bai,Yaoyao Qi,Bingzheng Yan,Yulei Wang,Zhiwei Lu

DOI: https://doi.org/10.1016/j.infrared.2023.105042

IF: 2.997

2024-01-01

Infrared Physics & Technology

Abstract:Controllable multi-wavelength gets worse efficiency and quality at high orders and high energy, remaining cascade Raman laser a challenge. Here, we establish an order controllable multi-wavelength cascaded diamond Raman laser to achieve the first-order to fifth-order Raman lasers output with wavelengths of 573.0, 620.3, 676.1, 743.0 and 824.7 nm. At a 532.8 nm pump energy of 1.60 mJ, the total Stokes output energy of 0.51 mJ with a slope efficiency of 36.5% has been achieved. Meanwhile, a Stokes output threshold model of all order is proposed under short pulse pumping for the first time. The threshold energy of the first-order to fifth-order was 256, 298, 320, 494, 1100 mu J separately, which is in consistent with the simulation results perfectly.
GHz-level repetition rate synchronously pumped diamond Raman laser based on bidirectional gain

Chengjie Zhu,Xuezong Yang,Yuxuan Liu,Muye Li,Yuxiang Sun,Jiajie Fang,Dijun Chen,Weibiao Chen,Yan Feng

DOI: https://doi.org/10.1063/5.0217381

IF: 4

2024-07-22

Applied Physics Letters

Abstract:In this paper, we demonstrate an ultrafast diamond Raman laser at 1240 nm with a pulse repetition rate of 956.62 MHz, a pulse duration of 39.5 ps, and an average power of up to 3.3 W based on synchronous pumping. The pump source is an electrical-pulse-modulated picosecond pulsed laser at 1064 nm with a repetition rate of 239.16 MHz and a pulse duration of 65.4 ps. A quadrupling repetition rate of the Raman pulse is achieved by synchronously amplifying both the forward and backward Raman pulses and the amplified Raman pulse undergoing two round trips in the resonator within one pump pulse period. The compression ratio of the pulse duration from the pump to the Raman is 1.66. This work offers a convenient and efficient method to significantly enhance the repetition rate of ultrafast crystalline Raman lasers and proves that a non-coherent ultrafast pump pulsed laser can be converted to a coherent mode-locked ultrafast Raman pulsed laser based on Raman conversion.

physics, applied
Picosecond synchronously pumped diamond Raman laser

Shuanghong Ding,Xinxin Huang,Qiaoshuang Zou

DOI: https://doi.org/10.1007/s00340-022-07922-8

2022-10-16

Abstract:With diamond crystals as Raman media, picosecond synchronously pumped solid-state Raman laser is theoretically studied in detail for the first time. High efficient working point and effective pulse compression working point are investigated. For both 532 nm and 1064 nm pumping, high Raman conversion efficiency can be achieved for negative cavity length detuning (∆ x ) and diamond crystal length of 5 mm. The higher efficiency can be obtained with longer Raman crystal, longer pumping pulse width and higher pumping power. For 532 nm pumping, effective pulse width compression can be realized for ∆ x = 0 nearby and diamond crystal length of 10 mm. Shorter pulse width and higher peak power of 1st Stokes laser can be achieved with longer Raman crystal, shorter pumping pulse width and higher pumping power. The findings can contribute to the design and optimization of picosecond synchronously pumped diamond Raman lasers.
Intracavity frequency-doubled pulsed diamond Raman laser emitting at 620 nm

Yilan Chen,Jiqiao Liu,Xiaolei Zhu,Mingjian Wang,Xuezong Yang,Yan Feng,Xiao Chen,Weibiao Chen

DOI: https://doi.org/10.1007/s00340-022-07908-6

2022-09-22

Abstract:An efficient intracavity frequency-doubled diamond Raman laser output at 620 nm wavelength is demonstrated. Laser output power of 750 mW at central wavelength of 620.1 nm was achieved successfully at a repetition rate of 2 kHz. The optical conversion efficiency was up to 11.0%. The laser beam M 2 factors were less than 1.6 and 1.3 in the x and y directions, respectively. This intracavity diamond Raman laser offers a new way towards generating efficient pulsed Raman red laser.
Isolator-free 60 W diamond Raman laser at 607 nm

A Sharp,H Jasbeer,R Pahlavani,D J Spence,O Kitzler,X Yang,R P Mildren

DOI: https://doi.org/10.1364/OL.538377

2024-09-15

Abstract:We report an intra-cavity frequency doubled diamond Raman laser operating at 607 nm. A z-fold cavity design was configured to prevent back reflections into the fiber amplifier, which avoided the use of isolators in the pump beam path. A maximum output power of 60 W was generated in two output beams at an optical conversion efficiency of 28% from the 1045 nm pump. A maximum single-beam output power of 40 W was obtained using a highly reflecting end mirror for the visible. Output power and single frequency stability are negatively impacted by an increasing role of stimulated Brillouin scattering at output powers above 10 W.
Enhanced Stimulated Brillouin Scattering Utilizing Raman Conversion in Diamond

Hui Chen,Zhenxu Bai,Xuezong Yang,Jie Ding,Yaoyao Qi,Bingzheng Yan,Yulei Wang,Zhiwei Lu,Richard P. Mildren

DOI: https://doi.org/10.1063/5.0087092

IF: 4

2022-01-01

Applied Physics Letters

Abstract:Cascaded Brillouin lasers based on guided-wave structures are applied across a range of important fields such as optical communications, microwave photonics, and sensing. However, restricted by the volume and available transmission range of the gain medium, the power output and wavelength diversity of guided-wave Brillouin devices are somewhat limited. In this work, we report the design and development of a cascaded Brillouin laser based utilizing a free-space optical layout with a diamond crystal as the Brillouin gain medium. A quasi-continuous-wave, 1 μm laser was used as the pump laser, and Raman wavelength conversion is used as an intermediate process to facilitate stimulated Brillouin scattering with a low threshold. When the output transmission of the diamond cavity is 0.37% and the incident pump power is 220 W, cascading of the Brillouin–Stokes field to the eighth Stokes and the seventh anti-Stokes orders was observed. By adjusting the cavity length, the order of the cascaded Brillouin laser output is controlled. A comprehensive analysis of the Brillouin generation process and the cascade of Stokes orders is undertaken for different incident pump powers and cavity lengths. This work is expected to enable practical applications of high-power Brillouin lasers and Brillouin frequency combs.
Order Controllable Enhanced Stimulated Brillouin Scattering Utilizing Cascaded Diamond Raman Conversion

Hui Chen,Zhenxu Bai,Yunpeng Cai,Xuezong Yang,Jie Ding,Yaoyao Qi,Bingzheng Yan,Yunfei Li,Yulei Wang,Zhiwei Lu,Richard P. Mildren

DOI: https://doi.org/10.1063/5.0137542

IF: 4

2023-01-01

Applied Physics Letters

Abstract:We report on the design and operation of a laser, which outputs wavelengths in the 1.2 and 1.5 μm ranges by leveraging two non-linear processes of stimulated Raman scattering and stimulated Brillouin scattering in diamond. By precisely controlling characteristics of the laser resonator formed around the diamond crystal, we are able to selectively control the onset of each non-linear process so as to tailor laser output characteristics both in way of wavelength and output power. This work demonstrates the high degree of flexibility and power-handling capacity of diamond for wavelength conversion of common laser wavelengths (such as 1064 nm as used in this work) and the generation of a span of discrete wavelengths (with up to eight cascaded orders being demonstrated in this work).
9 W Average Power, 150 Khz Repetition Rate Diamond Raman Laser at 1519 Nm, Pumped by a Yb Fibre Amplifier

Lukasz Dziechciarczyk,Zhimeng Huang,Giorgos Demetriou,Dan Cheng,Shankar Pidishety,Yujun Feng,Yutong Feng,Guozheng Wang,Huaiqin Lin,Sheng Zhu,Di Lin,Thomas W. Hawkins,Liang Dong,Alan Kemp,Johan Nilsson,Vasili Savitski

DOI: https://doi.org/10.1109/cleoe-eqec.2019.8873181

2019-01-01

Abstract:Commercially available pulsed fibre lasers at ∼1.5 μm have many uses in imaging, defense, communications and light radar (LIDAR) [1]. For 3D scanning LIDAR, higher signal-to-noise ratio requires lasers with high average power and high pulse repetition rate (ideally several MHz) for faster scanning rate, whereas to improve distance resolution requires pulse durations <10 ns [2,3]. One limitation of the pulsed fibre lasers at ∼1.5 μm is scaling to high average powers [4]. Raman frequency conversion of high average power fibre master oscillator power amplifier (MOPA) systems at ∼1 μm is a potential alternative. The large Raman shift and Raman gain of diamond allows two-stage Raman conversion to ∼1.5 μm for ∼1 μm pumping [5]. Excellent thermal properties make diamond suitable for high average powers [6]. Much work has been done on conversion of 1.064 μm lasers to 1.485 μm using diamond [7]; however, the "eye-safety" requirements for LIDAR typically call for wavelengths above 1.5 μm, due to the order of magnitude higher Maximum Permissible Exposure limit [8]. Developing such a diamond Raman laser (DRL) was the major motivation for this research.
A Narrow-Linewidth Linearly Polarized 1018-nm Fiber Source for Pumping Diamond Raman Laser

Xuezong Yang,Zhenxu Bai,Huawei Jiang,Richard P. Mildren,Yan Feng

DOI: https://doi.org/10.3389/fphy.2021.727109

IF: 3.718

2021-08-16

Frontiers in Physics

Abstract:A 7.8-GHz linewidth ytterbium-doped fiber (YDF) laser with an output power of 75 W at 1,018 nm is demonstrated based on narrow-bandwidth fiber Bragg gratings. Effective suppression of spectral broadening and amplified spontaneous emission is achieved by optimizing the resonator structure and active fiber parameters. An 1,178-nm diamond Raman output pumped by this narrow-linewidth 1,018 nm source is addressed in this study, which shows a promising application of generating the sodium guide star laser at 589 nm. A single-longitudinal-mode Stokes with an output power of 0.6 W is obtained using this multimode 1,018 nm laser at the pump power of 13 W. The impact of pump spectral linewidth on the effective Raman gain coefficient is analyzed, and the laser threshold of the diamond Stokes resonator increases with the broadening of the pump linewidth.

physics, multidisciplinary
Eye-safe diamond Raman laser

Yuqi Li,Zhenxu Bai,Hui Chen,Duo Jin,Xuezong Yang,Yaoyao Qi,Jie Ding,Yulei Wang,Zhiwei Lu

DOI: https://doi.org/10.1016/j.rinp.2019.102853

IF: 4.565

2020-03-01

Results in Physics

Abstract:Stimulated Raman scattering, as a third-order nonlinear effect, is an effective approach to expand the laser spectral region. To obtain a high power output of a Raman laser with a specific wavelength, novel Raman gain media and laser structures have been continuously studied, and in recent years, diamonds have received an increased interest from researchers owing to their extremely high Raman gain coefficient, high thermal conductivity, and wide transmission spectrum. Diamond Raman lasers (DRLs) have enabled the achievement of a laser input in the visible to the mid-infrared band. In particular, lasers with outputs in the 1.5 μm band have the characteristics of an atmospheric window and being eye-safe, which are critical for applications in the medical, distance measurement, radar, and other such domains. Consequently, researchers are constantly improving the methods to output a higher power laser at 1.5 μm, and the DRLs offer the potential to realize a high power and high beam quality in this band. This paper provides a review of the research status of 1.5 μm DRLs and suggests opportunities for future development and applications.

physics, multidisciplinary,materials science
Diamond Raman laser: a promising high-beam-quality and low-thermal-effect laser

Yulan Li,Jie Ding,Zhenxu Bai,Xuezong Yang,Yuqi Li,Jingling Tang,Yu Zhang,Yaoyao Qi,Yulei Wang,Zhiwei Lu

DOI: https://doi.org/10.1017/hpl.2021.25

IF: 4.8

2021-01-01

High Power Laser Science and Engineering

Abstract:Abstract Stimulated Raman-scattering-based lasers provide an effective way to achieve wavelength conversion. However, thermally induced beam degradation is a notorious obstacle to power scaling and it also limits the applicable range where high output beam quality is needed. Considerable research efforts have been devoted to developing Raman materials, with diamond being a promising candidate to acquire wavelength-versatile, high-power, and high-quality output beam owing to its excellent thermal properties, high Raman gain coefficient, and wide transmission range. The diamond Raman resonator is usually designed as an external-cavity pumped structure, which can easily eliminate the negative thermal effects of intracavity laser crystals. Diamond Raman converters also provide an approach to improve the beam quality owing to the Raman cleanup effect. This review outlines the research status of diamond Raman lasers, including beam quality optimization, Raman conversion, thermal effects, and prospects for future development directions.

optics
An integrated diamond Raman laser pumped in the near-visible

Pawel Latawiec,Vivek Venkataraman,Amirhassan Shams-Ansari,Matthew Markham,Marko Loncar

DOI: https://doi.org/10.1364/OL.43.000318

2017-12-13

Abstract:Using a high-Q diamond microresonator (Q > 300,000) interfaced with high-power-handling directly-written doped-glass waveguides, we demonstrate a Raman laser in an integrated platform pumped in the near-visible. Both TM-to-TE and TE-to-TE lasing is observed, with a Raman lasing threshold as low as 20 mW and Stokes power of over 1 mW at 120 mW pump power. Stokes emission is tuned over a 150 nm (60 THz) bandwidth around 875 nm wavelength, corresponding to 17.5% of the center frequency.

Optics
Numerical Simulation of Long-Wave Infrared Generation Using an External Cavity Diamond Raman Laser

Hui Chen,Zhenxu Bai,Chen Zhao,Xuezong Yang,Jie Ding,Yaoyao Qi,Yulei Wang,Zhiwei Lu

DOI: https://doi.org/10.3389/fphy.2021.671559

IF: 3.718

2021-07-05

Frontiers in Physics

Abstract:Diamond has a broad spectral transmission range (>0.2 μm) and the largest Raman frequency shift (1,332 cm −1 ) among known Raman crystals. Hence, the diamond Raman laser has the potential to achieve lasing in the long-wave infrared (LWIR) range, which is difficult to reach via other crystalline lasers. Here, we report a new approach to achieve LWIR output using diamond Raman conversion and provide the corresponding analysis model and simulation results. The conversion efficiency is analyzed as function of the pump waist size, output-coupler transmission, and crystal length, at constant pump power. The maximum output power at which a diamond of relatively large size can be operated without damage is predicted. This study paves a way for high-power LWIR lasing in diamond.

physics, multidisciplinary
Nanosecond pulse pumped, fiber-integrated narrow linewidth linearly polarized Raman amplifier at 1120 nm

Pengfei Zhang,Lijia Yang,Rongtao Su,Xiaolin Wang,Pu Zhou

DOI: https://doi.org/10.1117/12.2285040

2017-10-24

Abstract:In this manuscript, we demonstrated a watt-level average power narrow linewidth linearly polarized fiber-integrated Raman amplifier core pumped by a pulsed laser with center wavelength of 1064 nm. The gain medium in the amplifier stage is a 100-meters-long polarization-maintaining (PM) single-mode fiber. Seeded by a single-frequency (S-F) distributed feedback (DFB) diode laser, ~3.2 ns duration tunable 1120 nm laser is obtained with peak power of ~360 W. The average power of the Raman laser are 0.62W, 1.22 W and 1.83W with repetition rates of 500 KHz, 1 MHz and 1.5 MHz, respectively. More than 50% slope efficiency and 42 dB amplification is achieved. The polarization extinction rate (PER) of the Raman laser is measured to be ~21 dB.
Nanosecond pulse pumped, fiber-integrated narrow linewidth linearly polarized Raman amplifier at 1120nm

Pengfei Zhang,Lijia Yang,Rongtao Su,Xiaolin Wang,Pu Zhou

DOI: https://doi.org/10.1117/12.2285040

2017-01-01

Abstract:In this manuscript, we demonstrated a watt-level average power narrow linewidth linearly polarized fiber-integrated Raman amplifier core pumped by a pulsed laser with center wavelength of 1064 nm. The gain medium in the amplifier stage is a 100-meters-long polarization-maintaining (PM) single-mode fiber. Seeded by a single-frequency (S-F) distributed feedback (DFB) diode laser, similar to 3.2 ns duration tunable 1120 nm laser is obtained with peak power of similar to 360 W. The average power of the Raman laser are 0.62W, 1.22 W and 1.83W with repetition rates of 500 KHz, 1 MHz and 1.5 MHz, respectively. More than 50% slope efficiency and 42 dB amplification is achieved. The polarization extinction rate (PER) of the Raman laser is measured to be similar to 21 dB.
A Cascaded Brillouin Laser Using Diamond Raman Conversion

Hui Chen,Zhenxu Bai,Yunpeng Cai,Duo Jin,Richard P. Mildren,Yulei Wang,Zhiwei Lu

DOI: https://doi.org/10.1109/cleo-pr62338.2022.10431941

2022-01-01

Abstract:We demonstrate a diamond-based Brillouin laser with controllable, cascaded output spanning 15 cascaded SBS-Stokes-orders. Control of the cascading is achieved through both tailoring of the SBS cavity length and the SBS cavity output coupling.
Development of Beam Brightness Enhancement Based on Diamond Raman Conversion

Bai Zhenxu,Chen Hui,Li Yuqi,Yang Xuezong,Qi Yaoyao,Ding Jie,Wang Yulei,Lv Zhiwei

DOI: https://doi.org/10.3788/irla20200098

2021-01-01

Infrared and Laser Engineering

Abstract:High brightness laser sources with different wavelengths play an important role in the fields such as defense, industrial, and life sciences etc. However, due to the intrinsic spectral and thermophysical properties of current available laser gain materials, it is difficult to take into account the wavelength and output power of the traditional inversion lasers, which even leads to the decrease of beam brightness. To overcome this problem, beam cleanup by using nonlinear optical technology has been carried out in recent years, which is directly transferring the low beam quality generated from inversion lasers into the high through the effects such as stimulated Raman or Brillouin scattering. Among them, with excellent properties such as high Raman gain coefficient, high thermal conductivity and wide spectral transmission range, diamond exhibits excellent beam brightness enhancement characteristics while realizing high efficiency Raman conversion, which provides a new technical path to generate high power and high brightness laser beam. Here, the development of brightness enhancement based on first-order and cascaded Raman conversion of diamond was reviewed, and its future applications were discussed.

Collinear Raman Amplifier Based on Diamond

High-power dual-wavelength intracavity diamond Raman laser

On-Chip Diamond Raman Laser

Investigation of the Pulse Characteristics of an Injection Seeded Diamond Raman Amplifier

Order Controllable Multi-Wavelength Laser Utilizing Cascaded Diamond Raman Conversion

GHz-level repetition rate synchronously pumped diamond Raman laser based on bidirectional gain

Picosecond synchronously pumped diamond Raman laser

Intracavity frequency-doubled pulsed diamond Raman laser emitting at 620 nm

Isolator-free 60 W diamond Raman laser at 607 nm

Enhanced Stimulated Brillouin Scattering Utilizing Raman Conversion in Diamond

Order Controllable Enhanced Stimulated Brillouin Scattering Utilizing Cascaded Diamond Raman Conversion

9 W Average Power, 150 Khz Repetition Rate Diamond Raman Laser at 1519 Nm, Pumped by a Yb Fibre Amplifier

A Narrow-Linewidth Linearly Polarized 1018-nm Fiber Source for Pumping Diamond Raman Laser

Eye-safe diamond Raman laser

Diamond Raman laser: a promising high-beam-quality and low-thermal-effect laser

An integrated diamond Raman laser pumped in the near-visible

Numerical Simulation of Long-Wave Infrared Generation Using an External Cavity Diamond Raman Laser

Nanosecond pulse pumped, fiber-integrated narrow linewidth linearly polarized Raman amplifier at 1120 nm

Nanosecond pulse pumped, fiber-integrated narrow linewidth linearly polarized Raman amplifier at 1120nm

A Cascaded Brillouin Laser Using Diamond Raman Conversion

Development of Beam Brightness Enhancement Based on Diamond Raman Conversion