Abstract:With the progress in modern high-energy physics, the Standard Model is constantly being refined. As the last brick of the Standard Model, the Higgs boson was confirmed to be discovered in the Large Hadron Collider (LHC) in 2012. For the further exploration of the Higgs boson, the Circular Electron Positron Collider (CEPC) is proposed. The baseline detector concept of CEPC is guided by the particle flow principle. The Particle Flow Algorithm (PFA) reconstructs a list of low-level particles and associates every detector hit with these particles. The high granularity hadronic calorimeter (HCAL) represents an essential component of PFA-based detectors. This paper mainly presents the single-layer electronics design and development for the scintillator analog hadronic calorimeter prototype (AHCAL). The single-layer readout electronics consists of front-end electronics board (FEB) and data interface (DIF) board. The FEB carries the silicon photomultipliers (SiPM), plastic scintillators, and the SiPM signal readout circuit. A single SiPM coupled with a scintillator constitute the basic detection unit. The size of scintillator used here is 4 cm x 4 cm. A sensitive area of 72 x 72 cm(2) can be covered by the design presented here. 324 SiPMs coupled with scintillators are mounted on each FEB. Besides the huge sensitive area, The AHCAL prototype must also meet strict requirements on the integration and robustness of the electronics. This paper develops a complete single-layer readout electronics design that meets the requirements for use in the AHCAL. The results of beam test shows that the peak of the minimum ionizing particle (MIP) is separated from the pedestal evidently and the signal-to-noise ratio (SNR) is better than 20. The volume required for the electronics is less than 4 cm3 per channel. In addition, the FEB is sufficiently robust to avoid damage during intercontinental transportation. The development of the single-layer electronics represents significant progress in the design of a prototype device that meets the requirement for use in the CEPC.

Cosmic Ray Test of Shashlik Electromagnetic Calorimeter Modules for NICA-MPD

Beam Test Results of Two Shashlyk ECal Modules for NICA-MPD

Production and Quality Control of NICA-MPD Shashlik Electromagnetic Calorimeter in Tsinghua University

Development of shashlik electromagnetic calorimeter for the NICA/MPD

Improving the Spatial Resolution of NICA/MPD ECAL with New Reconstruction Methods

The Readout Electronics Research Design and Development for CEPC Scintillators Electromagnetic Calorimeter Prototype

Reconstruction and Simulation of the Performance of the Electromagnetic Calorimeter on MPD

Cosmic Ray Test On Csi(Tl) Modules Of Besii Electromagnetic Calorimeter

RADiCAL: Precision-timing, Ultracompact, Radiation-hard Electromagnetic Calorimetry

A Fast Front-end Readout Design for NICA-MPD Shashlik Electromagnetic Calorimeter

Scintillator Tile Batch Test of CEPC AHCAL

ECFA Detector R&D Panel, Review Report

Study of time and energy resolution of an ultra-compact sampling calorimeter (RADiCAL) module at EM shower maximum over the energy range 25 GeV $\leq$ E $\leq$ 150 GeV

R&D status for an innovative crystal calorimeter for the future Muon Collider

The Single-Layer Readout Electronics Design and Development for CEPC Scintillator Analog Hadronic Calorimeter Prototype

Readout Electronics Research for CEPC Semi-Digital Hadron Calorimeter Pre-prototype

Production and Test of Sphenix W/SciFiber Electromagnetic Calorimeter Blocks in China

Development of Future Electromagnetic Calorimeter Technologies and Applications for the Electron-Ion Collider with GEANT4 Simulations

Design of Sc-ECAL Prototype for CEPC and Performance of First Two Layers

Beam Test Results of the RADiCAL -- a Radiation Hard Innovative EM Calorimeter