Abstract:Injection of CO2 and water in saline aquifers or oil reservoirs causes changes of pressure, saturation and concentrations that affect the state of stress and promote chemical reactions in the host rock, resulting in porosity and permeability variations. It is therefore a coupled hydro-mechanical and chemical (HMC) problem. Numerical simulation of multiphase and multicomponent flow of CO2, oil and water with mechanical coupling allows realistic modeling of the reservoir and cap rocks. Carbonate reservoirs are geological formations composed mainly of minerals such as calcite and dolomite which can dissolve or precipitate in the medium when injecting a fluid of chemical composition and temperature different from those of the fluids initially contained in the rock. Water-weakening due to matrix acidification of carbonates is a well-known phenomenon that can be modeled by including mineral concentrations as state variables in the stress-strain behavior of the material. The objective of this work is to characterize synthetic carbonate rocks through microtomography and petrography techniques, focusing on a comparative analysis before and after load application and degradation with a reactive fluid [1]. The synthetic rocks were subjected to physical characterization (mineralogy, computed tomography and porosity) and mechanical characterization (uniaxial compressive strength and Brazilian tests) before and after the dissolution process. The petrographic analysis verified an increase in both intergranular and intragranular porosities after dissolution. The microtomography analysis quantified the maximum increase in porosity, from 11.8% to 41.3% in the two-dimensional analysis and 31.6% to 52% in the three-dimensional analysis of the porous structures. Furthermore, the pores were quantified according to their area, and data was obtained on the orientation of the pores, providing insight into the preferred paths of fluid flow. It was also observed that the microtomography technique was an effective tool for characterizing fractures in the samples before and after dissolution [1]. Dissolution tests were also performed in a modified oedometer cell adapted to measure horizontal stress. The dissolution phase was conducted using water and an acid solution to evaluate the influence of the pH on the mechanical behaviour of the samples. When the sample in the oedometric cell is exposed to an acid solution under constant vertical load of 400kPa, vertical displacement takes place (volume decrease of the sample) and horizontal stress increases (Figure 1). The synthetic rock used in this experiment is mainly composed by calcite, with small additions of calcium hydroxide, and the reactive fluid is water acidified with acetic acid (with 10% concentration). This material is manufactured in laboratory in order to have greater control of its constituents and reproducibility of experimental results. During the acidification phase of the experiment, the sample was subjected to an acid flow with a pressure differential of 12kPa for 7h. The behavior in Figure 1 was also observed by [2] and [3]. The model for degradation of carbonatic soft rocks proposed by [2] was implemented in a finite element code capable of performing coupled THMC analyzes in porous media [4]. This model is based on the Critical State Theory with the introduction of a bonding variable that controls the size of the yield surface by modifying the tensile strength and the pre-consolidation stress of the material. In Figure 1 it is also possible to see that the HMC coupled simulation of the oedometric test was able to reproduce the experimental results in terms of volumetric strain and horizontal stress. In Figure 2 tomographic images of the synthetic carbonate rock before and after exposure to the acid solution in an oedometric cell under constant vertical load are presented. Such analyses are crucial for the injection of reactive fluids, such as CO2, at high depths. Dissolution of minerals will affect not only the porosity and permeability of the reservoir rock but also, possibly, the stress state in the vicinity of the injection well.

Pore pressure estimation of the calcareous formations in the Middle Magdalena Valley Basin, Colombia

Effect of Groundwater Fluctuations on Pore Pressures and Earth Pressures on Coastal Excavation Retaining Walls

Feasibility study of pore pressure prediction in carbonate rocks

Shale Gas Reservoir Pore Pressure Prediction: A Case Study of the Wufeng–Longmaxi Formations in Sichuan Basin, Southwest China

Probabilistic Prediction Method of Formation Pore Pressure

Pore pressure study in the Irpinia area (Southern Apennines, Italy)

Pore-scale Imaging of Displacement Patterns in an Altered-Wettability Carbonate

Seismic and lithological near surface characteristics of an area in north-east Colombia

Geopressure evaluation using integrated basin modelling, well-logging and reservoir data analysis in the northern part of the Badri oil field, Gulf of Suez, Egypt

Minerals Dissolution Effect on the Mechanical Properties of Synthetic Carbonate Rocks

Pore pressure prediction in orthotropic medium based on rock physics modeling of shale gas

Application of GMDH to Predict Pore Pressure from Well Logs Data: A Case Study from Southeast Sichuan Basin, China

Poroacoustoelasticity for rocks with a dual-pore structure

Geomechanical methods for pore pressure prediction in complex geological structures: a case study of a field in southwest of Iran

Effects of organic richness, mineral composition, diagenesis, and thermal maturity on the viscoelastic properties of organic-rich Cretaceous mudstones in the Middle Magdalena Valley Basin, Colombia

Deterministic and Stochastic Modeling in Prediction of Petrophysical Properties of an Albian Carbonate Reservoir in the Campos Basin (Southeastern Brazil)

Prediction of lithology in lacustrine carbonates using well logs: The Cretaceous Barra Velha Formation in Santos Basin, offshore Brazil

Bayesian linearized inversion for petrophysical and pore-connectivity parameters with seismic elastic data of carbonate reservoirs

Prediction of stress components using the Beltrami-Michell method

Analysis on Prediction Methods for Formation Pore Pressure under Multiple Pressure Formation Mechanisms

Three-pressure prediction method of jointing well-seismic data in JT1 well area of Sichuan Basin in China