Abstract:Tip clearance flow between rotating blades and the stationary casing in high-pressure turbines is very complex and is one of the most important factors influencing turbine performance. The rotor with a winglet-cavity tip is often used as an effective method to improve the loss resulting from the tip clearance flow. In this study, an aerodynamic geometric optimisation of a winglet-cavity tip was carried out in a linear unshrouded high-pressure axial turbine cascade. For the purpose of shaping the efficient winglet geometry of the rotor tip, a novel parameterisation method has been introduced in the optimisation procedure based on the computational fluid dynamics simulation and analysis. The reliability of a commercial computational fluid dynamics code with different turbulence models was first validated by contrasting with the experimental results, and the numerical total pressure loss and flow angle using the Baseline k-omega Model (BSL κ-ω model) shows a better agreement with the test data. Geometric parameterisation of blade tips along the pressure side and suction side was adopted to optimise the tip clearance flow, and an optimal winglet-cavity tip was proven to achieve lower tip leakage mass flow rate and total pressure loss than the flat tip and cavity tip. Compared to the numerical results of flat tip and cavity tip, the optimised winglet-cavity design, with the winglet along the pressure side and suction side, had lower tip leakage mass flow rate and total pressure loss. It offered a 35.7% reduction in the change ratio [Formula: see text]. In addition, the optimised winglet along pressure side and suction side, respectively, by using the parameterisation method was studied for investigating the individual effect of the pressure-side winglet and suction-side winglet on the tip clearance flow. It was found that the suction-side extension of the optimal winglet resulted in a greater reduction of aerodynamic loss and leakage mass flow than the pressure-side extension of the optimal winglet. Moreover, with the analysis based on the tip flow pattern, the numerical results show that the pressure-side winglet reduced the contraction coefficient, and the suction-side winglet reduced the aerodynamic loss effectively by decreasing the driving pressure difference near the blade tips, the leakage flow velocity, and the interaction between the leakage flow and the main flow. Overall, a better aerodynamic performance can be obtained by adopting the pressure-side and suction-side winglet-cavity simultaneously.

Aerothermal Optimization and Sensitivity Analysis of a Turbine Rotor Tip with a Circumferential Casing Groove Configuration

Aerothermal optimization of a turbine rotor tip configuration based on free-form deformation approach

Effects of the circumferential casing groove configuration on aerothermal performance of a transonic turbine stage

Optimization of Rotor Tip Cavity Shapes for Mitigating Aerodynamic Tip Leakage Losses

Multi-objective Optimization Design of Aerothermal Performance for Turbine Blade Squealer Tip with Inclined Suction-Side Rim

Multi-Objective Optimization of Turbine Blade Tip With Film Cooling Holes

Aerodynamic Optimization of Winglet-Cavity Tip in an Axial High Pressure Turbine Stage

Treatment and Optimization of Casing and Blade Tip for Aerodynamic Control of Tip Leakage Flow in a Turbine Cascade

Aerothermal Optimization of Film Cooling Hole Locations on the Squealer Tip of an HP Turbine Blade

Influences of a Multi-Cavity Tip on the Blade Tip and the over Tip Casing Aerothermal Performance in a High Pressure Turbine Cascade

A cooled turbine blade design and optimization method considering the cooling structure influence

Aerodynamic topology optimization on tip configurations of turbine blades

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

Aerodynamic and Heat Transfer Optimization of One Stage Air-Cooled Turbine

Aerodynamic Optimisation of a Winglet-Cavity Tip in a High-Pressure Axial Turbine Cascade

Optimization of the Blade Profile and Cooling Structure in A Gas Turbine Stage Considering Both the Aerodynamics and Heat Transfer

Numerical Investigation of the Blade Tip and Overtip Casing Aerothermal Performance in a High Pressure Turbine Stage

Coupled Aerothermodynamics Optimization for the Cooling System of a Turbine Vane

Cooling layout optimization for a turbine blade squealer tip with the application of oval holes

Design and Optimization of Multiple Circumferential Casing Grooves Distribution Considering Sweep and Lean Variations on the Blade Tip

Controlling Leakage Flows Over a Rotor Blade Tip Using Air-Curtain Injection: Part I — Aero-Thermal Performance of Rotor Tips