Abstract:The study investigates the effects of graphene nanoplatelets (GNPs) on the tribological properties of aluminum-based nanocomposites, both annealed after extrusion and non-annealed. It also examines the role of nanosized Al4C3 (aluminum carbide), which forms in the annealed Al/GNPs nanocomposite, on the tribological performance of the nanocomposites. The nanocomposites were fabricated using the powder metallurgy method. The microstructure of the composite materials was characterized using SEM, EDS, XRD and TEM techniques. The coefficient of friction (CF) and mass wear of the composites were measured using a pin-on-disk test under dry sliding friction conditions. The results showed that adding GNPs increased the coefficient of friction (CF) of the nanocomposites by up to 44% at 0.1 wt.% GNP, but the CF decreased by 15% at 1.1 wt.% GNP. The optimal concentration of GNPs for minimizing the CF and mass wear of Al-based nanocomposites was 0.1 wt.%. Additionally, the presence of Al4C3 in the annealed Al/GNP nanocomposite had a positive effect on the CF at low GNP concentrations, with a 38% increases at 0.1 wt.% GNP, but this effect diminished as the GNP concentration increased. The study also found that the mass wear of the nanocomposites increased with the GNP concentration, with a 46% increase in the mass wear from 0.1 wt.% GNP to 0.5 wt.% GNP and a 202% increase from 0.1 wt.% GNP to 1.1 wt.% GNP. The presence of Al4C3 also affected the mass wear, with the effect diminishing as the GNP concentration increased. The study observed an increase in the mass wear with the increase in the GNP concentrations, but the mass wear of the annealed Al/GNPs with 1.1 wt.% GNP and Al4C3 was 52% lower than the Al composite with 1.1 wt.%. Overall, this study provides insights into the role of GNPs and Al4C3 on the tribological performance of aluminum-based nanocomposites.

Effect of graphene nanoplatelets on the mechanical properties and cutting performance of alumina nanocomposite ceramic tools prepared using the SPS-HF dual sintering method

Alumina ceramic tool material with enhanced properties through the addition of bionic prepared nano SiC@graphene

Mechanical properties and cutting performance of laminated graphene composite ceramic tools

Microstructure and Toughening Mechanisms of Al2O3/(W, Ti)C/graphene Composite Ceramic Tool Material

Investigating the Effects of Graphene Nanoplatelets and Al4C3 on the Tribological Performance of Aluminum-Based Nanocomposites

Mechanical and Tribological Properties of SiC-GNPs Composites Prepared by Oscillatory Pressure Sintering

Fabrication and mechanical properties of Al2O3–TiC ceramic composites synergistically reinforced with multi-walled carbon nanotubes and graphene nanoplates

Effect of SiC nanoparticle on microstructure and mechanical properties of graphene nanosheet (GNS) reinforced aluminum composites

The effect of sintering temperature and time on microstructure, hardness and wear behaviors of Al 99.9/GNP composites

Preparation and properties of graphene nanoplatelets reinforced aluminum composites

Effect of sintering temperature on microstructure and properties of graphene nanoplatelets reinforced TC21 composites prepared by spark plasma sintering

The Effects of Indium Additions on Tribological Behavior of Spark Plasma Sintering-Produced Graphene-Doped Alumina Matrix Composites for Self-Lubricating Applications

Effect of Fabrication Parameters on the Performance of 0.5 wt.% Graphene Nanoplates-Reinforced Aluminum Composites

Wear behavior of GNPs/ZrO2 reinforced composite ceramics sliding against Inconel 718

The Reinforcing Effect of Graphene Nano-Platelets on the Cryogenic Mechanical Properties of GNPs/Al2O3 Composites

Effect of graphene nanoplatelets addition on the elastic properties of short ceramic fiber-reinforced aluminum-based hybrid nanocomposites

Fabrication and properties of monolayer graphene reinforced Al2O3/TiN ceramic tool material

SiC-based Ceramic Materials Incorporating GNPs Array:Preparation and Mechanical Characterization

Characteristics and grinding performance evaluation of the high-fraction GNFs/SiCp/6061Al matrix hybrid composites

Preferentially oriented SiC/graphene composites for enhanced mechanical and thermal properties

High-content graphene nanoplatelet reinforced aluminum composites produced by ball milling and hot extrusion