Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Numerical Investigation of the Distributed Combustion in the Thermal Choked Solid Fuel Combined Cycle Engine

Numerical investigation on oxy-combustion characteristics of a 200MW e tangentially fired boiler

Numerical Investigation of the Combustion and Thermoacoustic Characteristics in an Annular Combustor with Hydrogen

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Numerical simulation of a chemical looping combustion of biomass: Hydrodynamic investigation

A reliable combustion strategy for a throttling-assisted supersonic combustor with flight Mach 7

Numerical Simulation and Flame Characteristics Analysis of Non-Premixed Swirling Combustion

Experimental and numerical study on a cavity-swirler-based combustion strategy for advanced gas turbine engine

Numerical Investigations of Supersonic Combustion Characteristics of Thermally Cracked Fuels at Typical Pyrolysis Temperatures

Numerical modeling of distributed combustion without air dilution in a novel ultra-low emission turbulent swirl burner

Numerical simulation of premixed n-heptane/air combustion in micro tube with internal channel optimization

Numerical Simulation of a Vortex Combustor Firing Dry Ultrafine Coal at 0.6 MW Thermal Input

Numerical Study on the Characteristics of Methane Hedging Combustion in a Heat Cycle Porous Media Burner

Numerical Investigation of a 1MW Full-Loop Chemical Looping Combustion Unit with Dual CFB Reactors

Numerical Investigation on Internal Regressing Shapes of Solid-Fuel Scramjet Combustor

Numerical Investigation Of High Speed Combustion And Its Impact On Thermal Structure

Numerical Investigation of Gas-Solid Two-Phase Flow in a Tiny-Oil Ignition Cyclone Burner for a 300-MW Down-Fired Pulverized Coal—Fired Boiler

Numerical Simulation of a 10 kW Gas-Fueled Chemical Looping Combustion Unit

Numerical analysis of afterburner chamber design for solid oxide fuel cell system

Numerical Investigation on the Jet Characteristics and Combustion Process of an Active Prechamber Combustion System Fueled with Natural Gas

Numerical Studies on Flame Inclination in Porous Media Combustors