Abstract:Structurally ordered L10-PtM (M = Fe, Co, Ni and so on) intermetallic nanocrystals, benefiting from the chemically ordered structure and higher stability, are one of the best electrocatalysts used for fuel cells. However, their practical development is greatly plagued by the challenge that the high-temperature (>600 °C) annealing treatment necessary for realizing the ordered structure usually leads to severe particle sintering, morphology change and low ordering degree, which makes it very difficult for the gram-scale preparation of desirable PtM intermetallic nanocrystals with high Pt content for practical fuel cell applications. Here we report a new concept involving the low-melting-point-metal (M' = Sn, Ga, In)-induced bond strength weakening strategy to reduce Ea and promote the ordering process of PtM (M = Ni, Co, Fe, Cu and Zn) alloy catalysts for a higher ordering degree. We demonstrate that the introduction of M' can reduce the ordering temperature to extremely low temperatures (≤450 °C) and thus enable the preparation of high-Pt-content (≥40 wt%) L10-Pt-M-M' intermetallic nanocrystals as well as ten-gram-scale production. X-ray spectroscopy studies, in situ electron microscopy and theoretical calculations reveal the fundamental mechanism of the Sn-facilitated ordering process at low temperatures, which involves weakened bond strength and consequently reduced Ea via Sn doping, the formation and fast diffusion of low-coordinated surface free atoms, and subsequent L10 nucleation. The developed L10-Ga-PtNi/C catalysts display outstanding performance in H2-air fuel cells under both light- and heavy-duty vehicle conditions. Under the latter condition, the 40% L10-Pt50Ni35Ga15/C catalyst delivers a high current density of 1.67 A cm-2 at 0.7 V and retains 80% of the current density after extended 90,000 cycles, which exceeds the United States Department of Energy performance metrics and represents among the best cathodic electrocatalysts for practical proton-exchange membrane fuel cells.

Liquid Metal Alloys Enable Efficient Formate Electrosynthesis

Liquid Metal-Enabled Tunable Synthesis of Nanoporous Polycrystalline Copper for Selective CO2-to-Formate Electrochemical Conversion

Synthesis of Planet‐Like Liquid Metal Nanodroplets with Promising Properties for Catalysis

Surface Enrichment in Gallium‐Indium Liquid Alloys: Applied to CO2 Conversion

Liquid Metal Alloy Catalysis – Challenges and Prospects

Liquid Metal‐Enabled Tunable Synthesis of Nanoporous Polycrystalline Copper for Selective CO2‐to‐Formate Electrochemical Conversion (Small 49/2024)

Pulsing Liquid Alloys for Nanomaterials Synthesis

Liquid Metal-Enabled Chemical Synthesis

Liquid-Metal-Mediated Electrocatalyst Support Engineering toward Enhanced Water Oxidation Reaction

Preliminary research on liquid electrode in electrocatalysis

An Atomic-scale Explanation For The High Selectivity Towards Carbon Dioxide Reduction Observed On Liquid Metal Catalysts

Galvanic Replacement of Liquid Metal Galinstan with Pt for the Synthesis of Electrocatalytically Active Nanomaterials.

Derived CuSn Alloys from Heterointerfaces in Bimetallic Oxides Promote the CO2 Electroreduction to Formate

Liquid Metal Based Flowable Regenerative Catalyst for Electrochemical Nitrate Reduction

Alloying/dealloying mechanisms, microstructural modulation and mechanical properties of nanoporous silver via a liquid metal-assisted alloying/dealloying strategy

Dynamic configurations of metallic atoms in the liquid state for selective propylene synthesis

Structural Evolution of Liquid Metals and Alloys

Formation of Multiphase Soft Metal from Compositing GaInSn and BiInSn Alloy Systems

'Painting' Nanostructured Metals-Playing With Liquid Metal

Highly Dispersed Indium Oxide Nanoparticles Supported on Carbon Nanorods Enabling Efficient Electrochemical CO2 Reduction

Metal bond strength regulation enables large-scale synthesis of intermetallic nanocrystals for practical fuel cells