Abstract:Abstract During different airplane flight modes, various effects may appear that need to be analyzed for both the oil and the fuel system at steady-state and transient operating modes. The effects, which relate to the cold temperature, associated with fuel freeze or wax point, cause a malfunction in the fuel pumps, nozzles, and other areas of the fuel system. On the other hand, high fuel temperature also leads to negative effects — the most common failure of high-flow fuel systems is cavitation, or “vapor-lock.” The combination of too much heat or too much inlet restriction can create this operating condition, where the liquid fuel literally boils inside the fuel pump. These effects are eliminated by the fuel/oil heat exchange system. In case of low fuel temperature, the fuel is used as a refrigerant to cool down hot oil coming from bearings. And in case of high fuel temperature, the oil serves as a coolant. This paper considers the method of evaluating normal and critical aircraft engine operation modes of the oil supply system with a fuel-oil heat exchanger utilizing an unsteady-state thermal-fluid network approach. The analyses are done based on the aircraft engine example to evaluate fuel and oil systems parameters variation in time under different flight conditions — the amount of fuel in the tank, inertial thermal effects, and the response time of the system to the regulation of the heat exchanger. The article is focused on sudden switching from a high to low gas engine operating mode. Fuel consumption to the engine is reduced abruptly, but the heat transfer from the bearings to the oil is still high due to thermal inertia. In this situation, a large amount of heated fuel must be returned to the fuel tank. At a certain point in time, the temperature of the fuel can reach a critical value. At the same time bearing cooling becomes ineffective, which leads to overheating. The calculation of thermal management system was performed at nominal conditions to obtain the initial data for low power settings analysis. As results of analysis at the low power settings mode the oil temperature before fuel cooled oil cooler is reached above 138 °C, which is high value. The failure of flow return valve is considered. The variations of oil temperature after the tank and increasing of fuel temperature at the tank in case of emergency situation are obtained. The influence of cooled fuel amount on the system thermal management is analyzed.

Transient Simulation on Flow and Heat Transfer Characteristics of Aeroengine Fuel-Oil Thermal Management System

Experiment and Simulation on a Thermal Management Scheme of Intermediate Circulation Based on Heat Current Method

Flow Dynamics in Transient Heat Transfer of N-Decane at Supercritical Pressure

Transient Analysis of Aircraft Oil Supply System With Fuel-Oil Heat Exchangers During Abrupt Change in Engine Operating Modes

Large Eddy Simulations of Heat Transfer and Thermal Oxidative Coking of Aviation Kerosene in Vertical U-Tube at a Supercritical Pressure

Modeling and Simulation of Supercritical-Pressure Turbulent Heat Transfer of Aviation Kerosene with Detailed Pyrolytic Chemical Reactions

Model Validation and Parametric Study of Fluid Flows and Heat Transfer of Aviation Kerosene with Endothermic Pyrolysis at Supercritical Pressure

Thermal Response Modeling and Analysis of Hydrocarbon Fuel Transient Flow and Heat Transfer at Supercritical Pressure

Simulation and Experimental Study on Thermal State of Engine Compartment of Commercial Vehicle

Large Eddy Simulations and Analyses of Hydrocarbon Fuel Heat Transfer in Vertical Upward Flows at Supercritical Pressures

Experimental study on the thermodynamic characteristics of the high temperature hydrocarbon fuel in the cooling channel of the hypersonic vehicle

Numerical Analysis on the Transient Thermal Status of Aircraft

Performance Simulation Analysis of Composite Thermal Management System for Hypersonic Vehicle

Thermal management of fuel heat sink in aircraft via flow path optimization

Numerical heat transfer analysis of transcritical hydrocarbon fuel flow in a tube partially filled with porous media

Thermal management method of fuel in advanced aeroengines

Heat transfer area optimization of intermediate heat-exchange cycle system for aero engines

Transient simulation of conjugate heat transfer of kerosene with thermal oxidative and surface coking reactions at a supercritical pressure

Modeling and simulation of aircraft integrated thermal management system

Simulation of diesel fuel heating under transient high pressure

Simulation of Transient Temperature and Clearance after Shutdown of Aeroengine Based on CFD and FEA Coupled Models