Abstract:Fouling control strategies play a crucial role in membrane distillation (MD) process, primarily due to the significant limitation of fouling during the scaling-up process. The utilization of microbubbles (MBs) aeration has exhibited promising potential in mitigating membrane fouling when treating high salinity wastewater. Aeration can introduce gas-liquid two-phase flow on the membrane surface, thereby increasing the membrane surface shear force. The mechanism of aeration technology for controlling fouling includes the following points: introduction of gas-liquid two-phase flow; physical substitution of concentration polarization layer; pressure pulses caused by bubbles flowing through the membrane surface and increasement of the cross flow velocity. This research aims to optimizing the effect of air MBs with different concentrations and sizes introduced in the feed side on membrane fouling control, we creatively used the method of releasing pressure gradiently to achieve size regulation of MBs within a certain range for the first time, firstly regulated the generation of MBs by manipulating gas flow rate and release pressure. Under the optimal condition of 40 mL/min and 0.6 MPa, it will yield concentration of 1.58 × 10 4 /mL and D50 Sauter size of 64.69 μm MBs with pure water permeance flux of 12.32 kg/(m 2 ·h). It was observed that higher gas flow rates primarily increased MBs concentration, while lower pressures predominantly reduced MBs size through the method of inline imaging. Experimental results indicated that introduction of MBs can slightly improve the temperature polarization coefficient and mass transfer coefficient under different operating modes. Consequently, further investigations focused on the influence of MBs characteristics on different fouling control. All conditions reach 99 % rejection for inorganic salt and HA. This study provided empirical evidence that higher concentration and larger size of MBs intensify the gas-liquid two-phase flow disruption and exhibit a better shear effect on scaling phenomena, which yield advantageous outcomes in terms of augmenting permeance flux and water vapor production, with permeance flux increased from 40.12 % to 55.42 % for inorganic fouling and increased from 68.35 % to 80.15 % for inorganic and HA fouling. These results were confirmed via membrane surface using scanning electron microscopy and energy dispersive spectroscopy. In summary, this research aided in identifying appropriate operating conditions for mitigating inorganic and composite scaling by implementing air-infused MBs in direct contact membrane distillation (DCMD), which provides scientific and technical guidance for controlling fouling in MD in practical applications.

Synergistically Controlling Biofouling and Improving Membrane Module Permeability by Using Simultaneously Structurally Optimized and Surface Modified Feed Spacers

Improved cleaning performance of membrane modules using feed spacers modified with cold-plasma treatment and polydopamine and silver-nanoparticle coatings

Roles and performance enhancement of feed spacer in spiral wound membrane modules for water treatment: A 20-year review on research evolvement

Preparation and Characterization of an Amphiphilic Polyamide Nanofiltration Membrane with Improved Antifouling Properties by Two-Step Surface Modification Method

Dynamic Evolution of Membrane Biofouling in Feed Channels Affected by Spacer–membrane Clearance and the Induced Hydrodynamic Conditions

Coral‐tentacle‐inspired antifouling membrane spacer: A natural solution for biofouling prevention

Impacts of non-uniform filament feed spacers characteristics on the hydraulic and anti-fouling performances in the spacer-filled membrane channels: Experiment and numerical simulation

The critical role of feed spacer channel porosity in membrane biofouling: Insights and implications

Enhancing ultrafiltration membrane permeability and antifouling performance through surface patterning with features resembling feed spacers

Surface functionalization via synergistic grafting of surface-modified silica nanoparticles and layered double hydroxide nanosheets for fabrication of superhydrophilic but relatively oleophobic antifouling membranes

In Situ Chemical Modification with Zwitterionic Copolymers of Nanofiltration Membranes: Cure for the Trade-Off between Filtration and Antifouling Performance

Optimizing fouling mitigation in membrane distillation by controlled microbubble size and concentration

Molecular design of antifouling ultrafiltration membranes via copolymerization of bactericidal and hydrophilic polymers

A mini-module with built-in spacers for high-throughput ultrafiltration

Surface Modification Of Membranes For Antibiofouling

Superior performance of a membrane bioreactor through innovative in-situ aeration and structural optimization using computational fluid dynamics

Surface modification of FeⅢ-juglone coating on nanofiltration membranes for efficient biofouling mitigation

Enhancing fouling mitigation of submerged flat-sheet membranes by vibrating 3D-spacers

Membrane surface coated with zwitterions for fouling mitigation in membrane bioreactor: Performance and mechanism

Stimuli-Responsive Lysozyme Nanocapsule Engineered Microfiltration Membranes with a Dual-Function of Anti-Adhesion and Antibacteria for Biofouling Mitigation

Antifouling Fibrous Membrane Enables High Efficiency and High-Flux Microfiltration for Water Treatment