Abstract:To reduce the decarburization of WC, the core-shell WC-16Cr3C2-10Co4Ni-La2O3 (named as WC-Cr3C2-CoNiLa in following) powder was prepared through second agglomeration and spray granulation process and deposited using high velocity oxygen fuel (HVOF) spraying. Microstructure and phase constitutions of the deposited coating were characterized using scanning electronic microscopy (SEM) with energy dispersive spectrometer (EDS) and X-ray diffraction (XRD), respectively. Microhardness, elastic modulus, and fracture toughness of the coating were tested by indentation method. Wear properties of the coating under different applied loads were evaluated by two body dry sliding wear using a pin-on-disc tester. Experimental results showed that the HVOF sprayed WC-Cr3C2-CoNiLa coating was mainly consisted of WC, Cr3C2, Co, Ni phases and a little of Cr2O3 without any WC decarburized phases including W2C, M6C and M12C). Most of WC carbide in the coating presented a round outline with the average particle size of 0.54 ± 0.35 μm and average crystal sizes 401 ± 91.41 Å in different crystal orientation index. The coating presented dense microstructure with the porosity about 1.16 ± 0.39%, and some lamella features with well bonded interfaces of carbide particles/binder phase, inter-splats and coating/substrate. Microhardness, elastic modulus, fracture toughness and wear rate of the coatings were 12.57 ± 0.52 Hv0.3, 153.91 ± 31.66 GPa, 5.31 ± 0.51 MPa⋅m1/2 and 6.67*10−3-11.11*10−3 mg/(Nm) when the applied load increased form 5 N to 15 N, respectively. The abrasive wear of the coating occurred mainly in the form of gouging and plastic deformation as well as peeling off carbide particles.

Transformation of Amorphous Phase in Nanostructured WC-10Co4Cr Coatings Induced by Heat Treatment and Accompanying Micromechanical Property Enhancement

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Mechanistic Investigation of the Interface Crystallization Behavior of Amorphous-Co Bonding Phase under Thermal Conditions and Its Impact on Cohesive Strength Via New Phase Precipitation

Effects of Heat Treatment on Structure Transformation of Cr/Al Composite Coatings

Microstructure and mechanical property of high velocity oxy-fuel sprayed WC-Cr3C2-Ni coatings

Fabrication and effect of heat treatment on the microstructure and tribology properties of HVOF-sprayed CoMoCrSi coating

Effect of Cobalt and Chromium Content on Microstructure and Properties of WC-Co-Cr Coatings Prepared by High-Velocity Oxy-Fuel Spraying

Role of carbide grit size and in-flight particle parameters on the microstructure, phases, and nanoscale properties of HVOF sprayed WC-12Co coatings

Effect of Particle and Carbide Grain Sizes on a HVOAF WC-Co-Cr Coating for the Future Application on Internal Surfaces: Microstructure and Wear

Influence of WC Particle Size on the Mechanical Properties and Residual Stress of HVOF Thermally Sprayed WC–10Co–4Cr Coatings

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

Influence of atomic migration mode at different temperatures on the microstructure, mechanical and cavitation erosion behaviors of Co-based alloy coating

The effect of carbide decomposition and carbon loss on the steady state composition of WC-Cr 3 C 2 -Ni composite coatings at 900 °C.

Effect of phase transformation of CoCrFeNiAl high-entropy alloy on mechanical properties of WC-CoCrFeNiAl composites

Microstructure, phase constitution and mechanical properties of WC-Cr3C2-CoNiLa coatings fabricated by using HVOF spraying core-shell powder

Microstructural evolution and wear characteristics of laser-clad CoCrFeNiMn high-entropy alloy coatings incorporating tungsten carbide

Comparison of Microwave Versus Conventional Furnace Heat Treatments of Carbide Composite Thermal Spray Coatings

Influence of Cr on the Surface Properties of the Micro-Textured WC+Co Alloy Coating

Mechanism for magnetic field induced structural relaxation and accompanying fracture toughness improvement of the thermal spraying coating

Microstructure and mechanical property of high velocity oxy-fuel sprayed multimodal WC-Cr3C2–Co–Y2O3 cermet coating

Revealing the microstructural evolution and mechanism during the thermomechanical treatment of polycrystalline CrCoNi medium-entropy alloy