Abstract:Sand–water flow characteristics of key overflow components of a Pelton turbine at rated operating conditions are analyzed; Completed sediment abrasion tests on a model testing machine for a Pelton turbine with a stand‐alone capacity of 500 MW; Pelton turbine critical overflow component wear life predicted. The problem of sediment wear presents a significant challenge for hydraulic turbines operating in sediment‐rich rivers, particularly for high‐head Pelton turbines. In this study, the VOF model, SST k–ω model, and DPM model were employed to simulate the gas–liquid–solid three‐phase flow within a large Pelton turbine, which operates under a rated water head of 671 m and has a single capacity of 500 MW, at a hydropower station situated on a sediment‐laden river. The sediment wear prediction model, derived from the sediment wear test of the model turbine, was utilized to forecast the sediment wear on the flow components of the Pelton turbine at the hydropower station. The results show that there are obvious pressure and velocity gradients near the nozzle outlet of the Pelton turbine in the power station, and the wear of the nozzle surface is gradually increasing, and the wear in the downstream area of the nozzle is more serious. The wear rate at the needle tip surface reached 1.372 μm/h, while the socket ring surface exhibited a wear rate of 3.175 μm/h. he highest wear rate recorded for the water bucket is 0.940 μm/h. After a year of continuous operation, the maximum erosion observed was 5.62 mm on the runner bucket made of stainless steel and wear‐resistant metal, 8.23 mm on the spray needle, and 19.05 mm on the nozzle mouth ring, highlighting the severity of sediment wear on the Pelton turbine. It is recommended that surface treatment technology be applied to the flow‐through components of the Pelton turbine at this hydropower station to enhance the wear resistance of the turbine and extend the operational life of the unit.

Numerical Analysis of the Sand Hydro-Abrasion of a Pelton Turbine Injector

Numerical Analysis of Sand Erosion for a Pelton Turbine Injector at High Concentration

Study on Internal Flow Characteristics and Abrasive Wear of Pelton Turbine in Sand Laden Water

Numerical simulation of multiphase flow and prediction of sediment wear in a large Pelton turbine

Sediment-laden Flow and Erosion Modeling in a Pelton Turbine Injector

Analysis of Sediment and Water Flow and Erosion Characteristics of Large Pelton Turbine Injector

Numerical Simulation of Solid-Liquid Two-Phase Flow and Wear Prediction of a Hydraulic Turbine High Sediment Content

Analysis of Sediment Erosion in Pelton Nozzles and Needles Affected by Particle Size

Analysis of hydro-abrasive erosion in a high-head Pelton turbine injector using a Eulerian-Lagrangian approach

Numerical prediction of erosion of Francis turbine in sediment laden flow

Pelton Turbine Needle Erosion Prediction Based on 3D Three- Phase Flow Simulation

Numerical Simulation and Experimental Study on Sediment Wear of Fixed Guide Vanes of Hydraulic Turbines in Muddy River Based on Discrete Phase Model

Investigation on the effect of particle parameters on the erosion and erosion prediction model of the Pelton turbine

Numerical simulation and abrasion prediction of two-phase turbulent flows through hydraulic turbine guide vanes

Effects of sediment characteristics on the erosion of Pelton turbine

Analysis of hydro-abrasive erosion in Pelton buckets using a Eulerian-Lagrangian approach

Numerical analysis of solid–liquidtwo-phase turbulent flow in Francis turbine runner with splitter bladesin sandy water

Numerical Prediction of Erosion of Francis Turbine in Sediment-Laden Flow under Different Heads

Experimental and Numerical studies on Opening and Velocity Influence on Sediment Erosion of Pelton Turbine Buckets

Prediction of sediment wear of francis turbine with high head and high sediment content

Analysis of the Air-Water-sediment Flow Behavior in Pelton Buckets Using a Eulerian-Lagrangian Approach