Toward Robust Lithium-Sulfur Batteries Via Advancing Li2S Deposition (vol 15, Pg 7949, 2024)

Xun Jiao,Xiaoxia Tang,Jinrui Li,Yujiao Xiang,Cunpu Li,Cheng Tong,Minhua Shao,Zidong Wei

DOI: https://doi.org/10.1039/d4sc90096k

IF: 8.4

2024-01-01

Chemical Science

Abstract:Correction for 'Toward robust lithium-sulfur batteries via advancing Li2S deposition' by Xun Jiao et al., Chem. Sci., 2024, https://doi.org/10.1039/D4SC02420F.

What problem does this paper attempt to address?

Correction: Toward robust lithium-sulfur batteries via advancing Li2S deposition.

Xun Jiao,Xiaoxia Tang,Jinrui Li,Yujiao Xiang,Cunpu Li,Cheng Tong,Minhua Shao,Zidong Wei

DOI: https://doi.org/10.1039/d4sc90096k

IF: 8.4

2024-01-01

Chemical Science

Abstract:[This corrects the article DOI: 10.1039/D4SC02420F.].
Toward Robust Lithium-Sulfur Batteries Via Advancing Li2S Deposition

Xun Jiao,Xiaoxia Tang,Jinrui Li,Yujiao Xiang,Cunpu Li,Cheng Tong,Minhua Shao,Zidong Wei

DOI: https://doi.org/10.1039/d4sc02420f

IF: 8.4

2024-01-01

Chemical Science

Abstract:Lithium-sulfur batteries (LSBs) with two typical platforms during discharge are prone to the formation of soluble lithium polysulfides (LiPS), leading to a decrease in the cycling life of the battery. Under practical working conditions, the transformation of S-8 into Li2S is cross-executed rather than a stepwise reaction, where the liquid LiPS to solid Li2S conversion can occur at a high state of charge (SOC) to maintain the current requirement. Therefore, advancing Li2S deposition can effectively reduce the accumulation of LiPSs and ultimately improve the reaction kinetics. Herein, a "butterfly material" GeS2-MoS2/rGO is used as a sulfur host. Rich catalytic heterointerfaces can be obtained via the abundant S-S bonds formed between GeS2 and MoS2. MoS2 (left wing) can enhance LiPS adsorption, while the lattice-matching nature of Fdd2 GeS2 (right wing) and Fm (3) over barm Li2S can induce multiple nucleation and regulate the 3D growth of Li2S. Li2S deposition can be advanced to occur at 80% SOC, thereby effectively inhibiting the accumulation of soluble LiPSs. Attributed to the synergistic effect of catalytic and lattice-matching properties, robust coin and pouch LSBs can be achieved.
Enhanced catalysis LiS<sub>3</sub> of radical-to-polysulfide interconversion <i>via</i> increased sulfur vacancies in lithium-sulfur batteries

Rui Xu,Hongan Tang,Yuanyuan Zhou,Fangzheng Wang,Hongrui Wang,Minhua Shao,Cunpu Li,Zidong Wei

DOI: https://doi.org/10.1039/d2sc01353c

IF: 8.4

2022-01-01

Chemical Science

Abstract:The practical application of lithium-sulfur (Li-S) batteries is seriously hindered by severe lithium polysulfide (LiPS) shuttling and sluggish electrochemical conversions. Herein, the Co9S8/MoS2 heterojunction as a model cathode host material is employed to discuss the performance improvement strategy and elucidate the catalytic mechanism. The introduction of sulfur vacancies can harmonize the chemisorption of the heterojunction component. Also, sulfur vacancies induce the generation of radicals, which participate in a liquidus disproportionated reaction to reduce the accumulation of liquid LiPSs. To assess the conversion efficiency from liquid LiPSs to solid Li2S, a new descriptor calculated from basic cyclic voltammetry curves, nucleation transformation ratio, is proposed.
Toward Robust Lithium-Sulfur Battery via Advancing Li2S Deposition

Xun Jiao,Xiaoxia Tang,Jinrui Li,Yujiao Xiang,Cunpu Li,Cheng Tong,Minhua Shao,Zidong Wei

DOI: https://doi.org/10.1039/d4sc02420f

IF: 8.4

2024-05-03

Chemical Science

Abstract:Lithium-sulfur batteries (LSBs) with two typical platforms during discharge are prone to the formation of soluble lithium polysulfides (LiPSs), leading to a decrease in the cycling life of the battery. In practical working conditions, the transformation of S8 to Li2S is cross-executed rather than stepwise reaction, where the liquid LiPSs to solid Li2S conversion can occur at high state of charge (SOC) to maintain the current requirement. Therefore, advancing the Li2S deposition can effectively reduce the accumulation of LiPSs and ultimately improve the reaction kinetics. Herein, a "butterfly material" GeS2 – MoS2 is elaborated as a sulfur host. Rich catalytic heterointerfaces can be obtained via the formed abundant S – S bonds between GeS2 and MoS2. The MoS2 (left wing) can enhance the LiPSs adsorption, while the lattice-matching nature of Fdd2 GeS2 (right wing) and Fm3m Li2S can induce multiple nucleation and regulate 3D growth of Li2S. The Li2S deposition can be advanced to occur at 80% SOC, thereby effectively inhibiting the accumulation of soluble LiPSs. Attributed to the synergistic effect of catalytic and lattice-matching properties, robust coin and pouch LSBs can be achieved.

chemistry, multidisciplinary
A Novel Strategy for High-Stability Lithium Sulfur Batteries by in Situ Formation of Polysulfide Adsorptive-Blocking Layer

Liming Jin,Gaoran Li,Binhong Liu,Zhoupeng Li,Junsheng Zheng,Jim P. Zheng

DOI: https://doi.org/10.1016/j.jpowsour.2017.04.059

IF: 9.2

2017-01-01

Journal of Power Sources

Abstract:Lithium sulfur (LiS) batteries are one of the most promising energy storage devices owing to their high energy and power density. However, the shuttle effect as a key barrier hinders its practical application by resulting in low coulombic efficiency and poor cycling performance. Herein, a novel design of in situ formed polysulfide adsorptive-blocking layer (PAL) on the cathode surface was developed to tame the polysulfide shuttling and promote the cycling stability for LiS batteries. The PAL is consisted of La2S3, which is capable to chemically adsorb polysulfide via the strong interaction of LaS bond and SS bond, and build an effective barrier against sulfur escaping. Moreover, the La2S3 is capable to suppress the crystallization of Li2S and promote the ion transfer, which contributes to the reduced internal resistance of batteries. Furthermore, the by-product LiNO3 simultaneously forms a stable anode solid and electrolyte interface to further inhibit the polysulfide shuttle. By this simple and convenient method, the resultant LiS batteries achieved exceptional cycling stability with an ultralow decay rate of 0.055% since the 10th cycle.
Study on Lithium-Sulfur Batteries

Yong-Gang Wang,Lina Wang,Shouyi Yuan,Yong-Yao Xia

DOI: https://doi.org/10.1149/ma2016-02/5/775

2016-01-01

ECS Meeting Abstracts

Abstract:Lithium-Sulfur (Li-S) batteries have recently raised worldwide attention owning to the high specific theoretical energy density of sulfur (2600Wh kg-1), the low cost and the wide availability of sulfur. However, the practical application of lithium-sulfur batteries has been hindered by several challenges, such as the shuttling of polysulfide intermediates, the large volume expansion of sulfur during charge/discharge and the dendrites formation on Li-anode. In this talk, we will introduce our recent investigation about Li-S batteries, including physical and chemical immobilization of sulfur to improve cycling stability, segregator optimization to minimize the shuttling effect and design of ionic liquids based electrolyte system to reduce the self-discharge. Finally, we introduce a lithium-ion sulfur battery based on a Li2S cathode using a dual-phase electrolyte (Li2S/electrolyte-1/LISICON/electrolyte-2/Li) and then replaced the Li anode with Al and graphite, which demonstrates a proof of concept of metal Li free Li-ion Sulfur battery. Reference [1] S.Y. Yuan, Z.Y. Guo, L.N. Wang, S. Hu, Y. G. Wang*, Y.Y. Xia*, Adv. Sci. 2015, 2: 1500071. [2] S.Y. Yuan, J.W. Bao, L.N. Wang, Y.Y. Xia, D.G. Truhlar*, Y.G. Wang*, Adv. Energy Mater., 2015 , 1501733. [3] L.N. Wang, J.Y. Liu, S. Haller, Y.G. Wang*, Y.Y. Xia*, Chem. Commun., 2015, 51: 6996. [4] L.N. Wang, J.Y. Liu, S.Y. Yuan, Y.G. Wang*, Y.Y. Xia*, Energy Environ. Sci., 2016, 9: 224. [5] L.N. Wang, Y.G. Wang*, Y.Y. Xia*, Energy Environ. Sci., 2015, 8: 1551.
Promoting the Transformation of Li2S2 to Li2S: Significantly Increasing Utilization of Active Materials for High‐Sulfur‐Loading Li–S Batteries

Xiaofei Yang,Xuejie Gao,Qian Sun,Sara Panahian Jand,Ying Yu,Yang Zhao,Xia Li,Keegan Adair,Liang-Yin Kuo,Jochen Rohrer,Jianneng Liang,Xiaoting Lin,Mohammad Norouzi Banis,Yongfeng Hu,Hongzhang Zhang,Xianfeng Li,Ruying Li,Huamin Zhang,Payam Kaghazchi,Tsun-Kong Sham,Xueliang Sun

DOI: https://doi.org/10.1002/adma.201901220

IF: 29.4

2019-01-01

Advanced Materials

Abstract:Lithium-sulfur (Li-S) batteries with high sulfur loading are urgently required in order to take advantage of their high theoretical energy density. Ether-based Li-S batteries involve sophisticated multistep solid-liquid-solid-solid electrochemical reaction mechanisms. Recently, studies on Li-S batteries have widely focused on the initial solid (sulfur)-liquid (soluble polysulfide)-solid (Li2S2) conversion reactions, which contribute to the first 50% of the theoretical capacity of the Li-S batteries. Nonetheless, the sluggish kinetics of the solid-solid conversion from solid-state intermediate product Li2S2 to the final discharge product Li2S (corresponding to the last 50% of the theoretical capacity) leads to the premature end of discharge, resulting in low discharge capacity output and low sulfur utilization. To tackle the aforementioned issue, a catalyst of amorphous cobalt sulfide (CoS3) is proposed to decrease the dissociation energy of Li2S2 and propel the electrochemical transformation of Li2S2 to Li2S. The CoS3 catalyst plays a critical role in improving the sulfur utilization, especially in high-loading sulfur cathodes (3-10 mg cm(-2)). Accordingly, the Li2S/Li2S2 ratio in the discharge products increased to 5.60/1 from 1/1.63 with CoS3 catalyst, resulting in a sulfur utilization increase of 20% (335 mAh g(-1)) compared to the counterpart sulfur electrode without CoS3.
Promoting the Transformation of Li2 S2 to Li2 S: Significantly Increasing Utilization of Active Materials for High-Sulfur-Loading Li-S Batteries

Xiaofei Yang,Xuejie Gao,Qian Sun,Sara Panahian Jand,Ying Yu,Yang Zhao,Xia Li,Keegan Adair,Liang-Yin Kuo,Jochen Rohrer,Jianneng Liang,Xiaoting Lin,Mohammad Norouzi Banis,Yongfeng Hu,Hongzhang Zhang,Xianfeng Li,Ruying Li,Huamin Zhang,Payam Kaghazchi,Tsun-Kong Sham,Xueliang Sun

DOI: https://doi.org/10.1002/adma.201901220

Abstract:Lithium-sulfur (Li-S) batteries with high sulfur loading are urgently required in order to take advantage of their high theoretical energy density. Ether-based Li-S batteries involve sophisticated multistep solid-liquid-solid-solid electrochemical reaction mechanisms. Recently, studies on Li-S batteries have widely focused on the initial solid (sulfur)-liquid (soluble polysulfide)-solid (Li2 S2 ) conversion reactions, which contribute to the first 50% of the theoretical capacity of the Li-S batteries. Nonetheless, the sluggish kinetics of the solid-solid conversion from solid-state intermediate product Li2 S2 to the final discharge product Li2 S (corresponding to the last 50% of the theoretical capacity) leads to the premature end of discharge, resulting in low discharge capacity output and low sulfur utilization. To tackle the aforementioned issue, a catalyst of amorphous cobalt sulfide (CoS3 ) is proposed to decrease the dissociation energy of Li2 S2 and propel the electrochemical transformation of Li2 S2 to Li2 S. The CoS3 catalyst plays a critical role in improving the sulfur utilization, especially in high-loading sulfur cathodes (3-10 mg cm-2 ). Accordingly, the Li2 S/Li2 S2 ratio in the discharge products increased to 5.60/1 from 1/1.63 with CoS3 catalyst, resulting in a sulfur utilization increase of 20% (335 mAh g-1 ) compared to the counterpart sulfur electrode without CoS3 .
Regulating Li2S Deposition and Accelerating Conversion Kinetics Through Intracavity ZnS Toward Low-Temperature Lithium-Sulfur Batteries.

Hao Ding,Zhonghui Chen,Huiyu Li,Huadong Suo,Chaozhong Liu,Huanan Yu,Jingkun Yuan,Zixu Sun,Yanyan Zhu,Bo Song

DOI: https://doi.org/10.1021/acs.nanolett.4c04427

IF: 10.8

2024-01-01

Nano Letters

Abstract:The uncontrolled deposition behavior and sluggish conversion kinetics of the discharging product (solid Li2S) severely deteriorate the electrochemical performance of lithium-sulfur (Li-S) batteries, especially under high S loading and low-temperature conditions. Herein, a multifunctional S cathode host consisting of ZnS nanoparticles (NPs) confined in hollow porous carbon spheres (ZnS@HPCS) is synthesized via a unique capillary force-driven melting-diffusion strategy. The porous carbon shell of ZnS@HPCS provides a space-confined reservoir for soluble polysulfides and solid Li2S, while the intracavity ZnS NPs trap polysulfides, induce Li2S inside deposition, and accelerate conversion kinetics. Thus, Li-S batteries with ZnS@HPCS-S cathodes exhibit excellent electrochemical performance at both room and low temperatures (-40 °C) and high reversible capacities under high S loading (5.2 mg cm-2). Furthermore, Li2S nucleation/deposition, in situ Raman, and theoretical analyses reveal the underlying mechanism. This work offers fundamental insights into regulating Li2S deposition and designing S hosts for high-performance Li-S batteries.
Electrochemical deposition of Li2S2/Li2S in aprotic Li–S batteries

Zhifeng Yao,Xiaozhong Fan,Long Kong

DOI: https://doi.org/10.1016/j.partic.2024.01.011

IF: 3.5

2024-07-01

Particuology

Abstract:Lithium–sulfur (Li–S) batteries stand out the energy storage systems because of extremely high energy density (2600 W h Kg−1) and low-cost sulfur cathode. Unfortunately, the sluggish deposition from liquid Li polysulfides (LiPSs) to solid Li2S leads to mild power density and short cycle life. Understanding and regulating Li2S2/Li2S deposition are conceived to be importance to deliver second-plateau capacity in acceptable kinetics, which has the potential to operation Li–S batteries under electrolyte-lean conditions. This perspective aims to summarize the proposed models that can describe the nucleation and propagation of three-dimensional Li2S2/Li2S, as well as affords critical views how electrolyte dictates LiPS conversion from liquid to solid. It hopes to encourage necessary scaffold strategies and electrolyte formulations to further improve energy density and life span of Li–S batteries.

materials science, multidisciplinary,engineering, chemical
Towards High Performance Li–S Batteries via Sulfonate‐Rich COF‐Modified Separator

Jie Xu,Shuhao An,Xianyu Song,Yongjie Cao,Nan Wang,Xuan Qiu,Yu Zhang,Jiawei Chen,Xianli Duan,Jianhang Huang,Wei Li,Yonggang Wang

DOI: https://doi.org/10.1002/adma.202105178

IF: 29.4

2021-10-07

Advanced Materials

Abstract:Lithium–sulfur (Li–S) batteries are held great promise for next-generation high-energy-density devices; however, polysulfide shuttle and Li-dendrite growth severely hinders their commercial production. Herein, a sulfonate-rich COF (SCOF-2) is designed, synthesized, and used to modify the separator of Li–S batteries, providing a solution for the above challenges. It is found that the SCOF-2 features stronger electronegativity and larger interlayer spacing than that of none/monosulfonate COFs, which can facilitate the Li+ migration and alleviate the formation of Li-dendrites. Density functional theory (DFT) calculations and in situ Raman analysis demonstrate that the SCOF-2 possesses a narrow bandgap and strong interaction on sulfur species, thereby suppressing self-discharge behavior. As a result, the modified batteries deliver an ultralow attenuation rate of 0.047% per cycle over 800 cycles at 1 C, and excellent anti-self-discharge performance by a low-capacity attenuation of 6.0% over one week. Additionally, even with the high-sulfur-loading cathode (3.2–8.2 mgs cm-2) and lean electrolyte (5 µL mgs-1), the batteries still exhibit ≈80% capacity retention over 100 cycles, showing great potential for practical application.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Cathode Nanostructuring and Separator Modification for High-Performance Lithium-Sulfur Batteries

Xiaoyun Yu,Guangmin Zhou,Yi Cui

DOI: https://doi.org/10.1149/ma2018-01/3/306

2018-01-01

ECS Meeting Abstracts

Abstract:Battery technologies involving Li-S chemistry are promising approaches to realize inexpensive and high energy density storage for sustainable energy applications. However, current Li-S batteries still suffer from short life-time due to active material loss through the soluble polysulfide molecules shuttling between battery cathode and anode.[1] We present herein our recent advances in the understanding of the electrochemical reactions at Li-S battery cathode and addressing the shuttle effect by polysulfide trapping. Specifically, an in-operando characterization technique based on optical microscopy is developed to intuitively visualize the selective deposition of sulfur and Li2S in battery cathodes, and the critical roles of current collectors and additives, including different metals and semiconductors, are demonstrated. Accordingly, innovative cathode architectures are designed to control the oriented deposition and diffusion of sulfur-containing species. In particular, an ultrathin and compact blocking layer of 2D MoS2 and WS2 nanoflakes, with a thickness of ca. 15 nm, are deposited on separator through a solution based self-assembly method,[2] which effectively adsorb polysulfide molecules and thus suppress their diffusion to the battery anode. In addition, Li2S-metal composites and polymer-metal hybrid networks are fabricated as hosts for sulfur cathodes to enable rapid battery charge-discharge processes given the large active surface area and better control of charge (or discharge) product deposition.[3] Combining these two strategies, we report greatly enhanced specific capacity (over 1200 mAh g-1) and cyclability (over 500 cycles) for the nanostructured sulfur cathodes compared to the conventional carbon-sulfur based cathode, and the routes to further improving high-energy and long-life Li-S battery are discussed. [1] Seh, Z. W.; Sun, Y.; Zhang, Q.; Cui, Y. Chem. Soc. Rev. 2016, 45, 5605. [2] Yu, X.; Prévot, M. S.; Guijarro, N.; Sivula, K. Nat. Commun. 2015, 6, 7596. [3] Zhou, G. M.; Sun, J.; Jin, Y.; Chen, W.; Zu, C. X.; Zhang, R. F.; Qiu, Y. C.; Zhao, J.; Zhuo, D.; Liu, Y. Y.; Tao, X. Y.; Liu, W.; Yan, K.; Lee, H. R.; Cui, Y. Adv. Mater. 2017, 29, 1603366
In Situ Synthesis of Organopolysulfides Enabling Spatial and Kinetic Co-Mediation of Sulfur Chemistry

Cheng Jiang,Lulu Li,Qingqing Jia,Mi Tang,Kun Fan,Yuan Chen,Chenyang Zhang,Minglei Mao,Jing Ma,Wenping Hu,Chengliang Wang

DOI: https://doi.org/10.1021/acsnano.2c01390

IF: 17.1

2022-05-23

ACS Nano

Abstract:Li-S batteries have been regarded as one of the most promising alternatives of the next-generation Li batteries. However, the dissolution and shuttling of lithium polysulfides lead to low cycle stability and low Coulombic efficiency, which intensively hinder the practical application of Li-S batteries. Herein, we propose a strategy to simultaneously promote the redox kinetics and inhibit the shuttle of lithium polysulfides, through in situ synthesis of insoluble organopolysulfides by adding a special additive. Attractively, the thus-formed insoluble organopolysulfides in the form of nanoparticle aggregates are also capable of adsorbing unconverted lithium polysulfides and hence effectively spatially suppress the shuttle effect. Furthermore, the organopolysulfides served as active redox mediators, showing faster redox kinetics of S chemistry than that of lithium polysulfides. As a result, the Li-S batteries showed impressive capacity, improved rate performance, and long cycling stability even under lean-electrolyte and high sulfur loading conditions.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Synergistic Interfacial Optimization for High-Sulfur-Content All-Solid-State Lithium-Sulfur Batteries

BoSheng Zhao,Chang Zhou,Peng Chen,XuePing Gao

DOI: https://doi.org/10.1021/acsami.3c16067

2024-01-31

Abstract:Improving the sulfur content in the cathode is essential for achieving high-energy-density all-solid-state lithium-sulfur batteries (ASSLSBs). However, the complex multiinterfaces, akin to the short wooden planks that consist of the cask, severely limit the performance of ASSLSBs with high sulfur content. Since singular approaches fail to optimize these interfaces simultaneously, we propose a synergistic approach using a dual-doped sulfide solid electrolyte (Y2S3 and LiI) and an SbSn alloy sulfur host in this work. The incorporation of Y2S3 in the solid electrolyte serves to improve the electrolyte-electrolyte interfaces and enhance the ionic conductivity, while the inclusion of LiI helps stabilize the electrolyte-anode interface and suppress dendrite formation. Meanwhile, the SbSn alloy sulfur host facilitates the transfer of Li+ at the electrolyte-cathode interfaces. Consequently, the solid-solid interfaces are significantly improved, leading to impressive specific capacities in ASSLSBs with high sulfur content (>44% in the cathode composite) at room temperature (1163.5 mAh g-1) and at 60 °C (1408.7 mAh g-1) during the 50th cycle at 0.05C. This work presents a promising strategy for achieving practical high-performance ASSLSBs.
Progress on critical cell fabrication parameters and designs for advanced lithium–sulfur batteries

Cheng-Che Wu,Tzu-Ching Chan,Sheng-Heng Chung

DOI: https://doi.org/10.1039/d4cc03085k

IF: 4.9

2024-08-18

Chemical Communications

Abstract:Since 1990, commercial lithium-ion batteries have made significant strides, approaching their theoretical performance limits, albeit with escalating costs. To address these challenges, attention has shifted toward lithium–sulfur batteries, which offer higher theoretical energy densities and cost-effectiveness. However, lithium–sulfur cells face challenges such as active-material loss, excessive electrolyte usage, and rapid degradation of lithium–metal anodes. To overcome these issues, research has focused on optimizing cell configurations and fabrication parameters while exploring novel electrolytes and electrode materials. This feature article delves into the intrinsic material challenges and extrinsic engineering issues in current lithium–sulfur research and explores the development of advanced lithium–sulfur cells with crucial progress on high-loading sulfur cathodes, lean-electrolyte cells, and solid-state electrolytes. Moreover, it outlines the fundamental principles, structures, performances, and developmental trajectories indicated in research articles published after 2020, highlighting future research directions aimed at resolving key challenges for the practical application of lithium–sulfur cells.

chemistry, multidisciplinary
Ferrous Sulfide-Assisted Hollow Carbon Spheres As Sulfur Host for Advanced Lithium-Sulfur Batteries

Weiwei Yang,Hao Zhao,Liang Chen,Chun Fang,Zhiyan Rui,Longqi Yang,Hong Wan,Jianguo Liu,Yong Zhou,Peng Wang,Zhigang Zou

DOI: https://doi.org/10.1016/j.cej.2017.06.050

IF: 15.1

2017-01-01

Chemical Engineering Journal

Abstract:Lithium-sulfur (Li-S) batteries have attracted extensive interests for its high theoretical energy density, but its further applications are blocked by capacity loss as a result of the shuttling of lithium polysulfides (LiPSs). A ferrous sulfide-stabilized S-hollow carbon sphere group (BP2000-FeS-S) was fabricated by supporting conductive ferrous sulfide (FeS) into a hollow carbon sphere group (BP2000), followed by traditional wet-impregnating of S. The BP2000 host physically confines LiPSs while FeS is anchored inside BP2000 and further chemically interact with LiPSs through bonding with FeS. Meanwhile, FeS acts as the filling inside the hole of BP2000 adjusting an appropriate aperture size to restricting the drain of S/LiPSs. The BP2000-FeS-S cathode displayed reversible capacity of 1206.2 mA h g (1) at 0.1 C and capacity could be maintained at 691.7 mA h g (1) after more than 500 progressive cycles at a current density of 0.5 C. What's more, the BP2000-FeS-S cathode could output a capacity up to 659.2 mA h g (1) even at a current density of 2 C. This strategy can be widely extended to other kinds of metal sulfides or nitrides and probably be used widely. (C) 2017 Elsevier B.V. All rights reserved.
Li-Ion Intercalating Cathode for Advanced Lithium-Sulfur Batteries

Jun Hyuk Moon

DOI: https://doi.org/10.1149/ma2024-012486mtgabs

2024-08-09

ECS Meeting Abstracts

Abstract:The advancement of lithium-sulfur (Li-S) batteries represents a significant shift in high-energy-density electrochemical storage, offering energy densities far exceeding those of traditional lithium-ion systems. This research contributes to the evolving field of Li-S batteries by proposing a novel strategy to optimize cathode performance, crucial in harnessing their full potential. Li-S batteries are characterized by their unique electrochemical process, which involves converting elemental sulfur to lithium sulfide (Li 2 S) during discharge via lithium polysulfide intermediates. A traditional challenge in this process is the notorious shuttle effect caused by lithium polysulfide intermediates. These intermediates, highly soluble in standard electrolytes, migrate continuously between the cathode and anode, leading to substantial active material loss, rapid capacity degradation, and reduced coulombic efficiency. Significant advancements have been made by introducing metal compounds with a chemical affinity for lithium polysulfides. However, a persistent challenge remains: the insulating nature of Li 2 S, which hinders electron transport. Recent strategies aiming to address these issues have focused on electrolytes with enhanced Li 2 S solubility to promote three-dimensional (3D) Li 2 S growth and prevent cathode passivation. Yet, the increased reactivity of such electrolytes poses new challenges, highlighting the need for alternative solutions. Our study explores this challenge, utilizing lithiated metal oxides as intercalating cathode materials to control Li 2 S growth dynamics. This method offers immediate mitigation of side reactions in the implementation of enhanced electrolytes. The scope of our research encompasses the thorough synthesis and characterization of these intercalating oxides, emphasizing their role in control Li 2 S growth. Additionally, we delve into the electrochemical characterization of these materials, focusing on their lithiation/delithiation kinetics and the consequent impact on Li-S battery performance. These intercalating oxides, capable of incorporating lithium ions within their crystal structure, present a promising path for aligning lithiation with Li 2 S formation, thereby fostering effective 3D growth. This contrasts with other oxides where asynchronous lithiation results in conventional two-dimensional (2D) Li 2 S growth, leading to premature discharge termination and suboptimal battery performance. We introduce a mechanism where 3D Li 2 S growth is driven by enhanced solvation of Li 2 S, intricately linked to the lithiation behavior of these oxides. By incorporating these optimized intercalating oxides in Li-S cells, we observe notable improvements in discharge capacity and sulfur utilization. This improvement is especially significant under high sulfur loading conditions, which typically exacerbate the polysulfide shuttle effect and pose formidable challenges for Li-S battery efficiency. Our investigation includes a detailed morphological analysis of Li 2 S deposition on various cathode surfaces. Employing advanced techniques like ex-situ Scanning Electron Microscopy (SEM) and electrodeposition modeling, we discern distinct Li 2 S growth patterns. These findings reveal that cathodes incorporating specific intercalating oxides exhibit reduced surface passivation due to predominant 3D Li 2 S growth, as opposed to the 2D growth observed in other oxide substrates. This variation in growth morphology significantly impacts cell performance, particularly under high sulfur loading conditions, where effective management of Li 2 S formation and polysulfide shuttling is crucial. In conclusion, this research marks a significant step in addressing the fundamental challenges of Li-S batteries. By leveraging the distinct properties of select intercalating oxides, the study not only deepens our understanding of Li 2 S growth mechanisms but also demonstrates an effective method to enhance Li-S battery performance. This work lays a foundation for future developments in high-energy-density battery technologies and signifies a crucial advancement towards the realization of more efficient and robust Li-S batteries.
Directing the Lithium–Sulfur Reaction Pathway via Sparingly Solvating Electrolytes for High Energy Density Batteries

Chang-Wook Lee,Quan Pang,Seungbum Ha,Lei Cheng,Sang-Don Han,Kevin R. Zavadil,Kevin G. Gallagher,Linda F. Nazar,Mahalingam Balasubramanian

DOI: https://doi.org/10.1021/acscentsci.7b00123

IF: 18.2

2017-05-25

ACS Central Science

Abstract:The lithium-sulfur battery has long been seen as a potential next generation battery chemistry for electric vehicles owing to the high theoretical specific energy and low cost of sulfur. However, even state-of-the-art lithium-sulfur batteries suffer from short lifetimes due to the migration of highly soluble polysulfide intermediates and exhibit less than desired energy density due to the required excess electrolyte. The use of sparingly solvating electrolytes in lithium-sulfur batteries is a promising approach to decouple electrolyte quantity from reaction mechanism, thus creating a pathway toward high energy density that deviates from the current catholyte approach. Herein, we demonstrate that sparingly solvating electrolytes based on compact, polar molecules with a 2:1 ratio of a functional group to lithium salt can fundamentally redirect the lithium-sulfur reaction pathway by inhibiting the traditional mechanism that is based on fully solvated intermediates. In contrast to the standard catholyte sulfur electrochemistry, sparingly solvating electrolytes promote intermediate- and short-chain polysulfide formation during the first third of discharge, before disproportionation results in crystalline lithium sulfide and a restricted fraction of soluble polysulfides which are further reduced during the remaining discharge. Moreover, operation at intermediate temperatures ca. 50 °C allows for minimal overpotentials and high utilization of sulfur at practical rates. This discovery opens the door to a new wave of scientific inquiry based on modifying the electrolyte local structure to tune and control the reaction pathway of many precipitation-dissolution chemistries, lithium-sulfur and beyond.

chemistry, multidisciplinary
Advances in lithium–sulfur batteries based on multifunctional cathodes and electrolytes

Quan Pang,Xiao Liang,Chun Yuen Kwok,Linda F. Nazar

DOI: https://doi.org/10.1038/nenergy.2016.132

IF: 56.7

2016-09-01

Nature Energy

Abstract:Amid burgeoning environmental concerns, electrochemical energy storage has rapidly gained momentum. Among the contenders in the ‘beyond lithium’ energy storage arena, the lithium–sulfur (Li–S) battery has emerged as particularly promising, owing to its potential to reversibly store considerable electrical energy at low cost. Whether or not Li–S energy storage will be able to fulfil this potential depends on simultaneously solving many aspects of its underlying conversion chemistry. Here, we review recent developments in tackling the dissolution of polysulfides — a fundamental problem in Li–S batteries — focusing on both experimental and computational approaches to tailor the chemical interactions between the sulfur host materials and polysulfides. We also discuss smart cathode architectures enabled by recent materials engineering, especially for high areal sulfur loading, as well as innovative electrolyte design to control the solubility of polysulfides. Key factors that allow long-life and high-loading Li–S batteries are summarized.

materials science, multidisciplinary,energy & fuels
Lithium-Sulfur Batteries: Review on High-Loading and High-Energy Lithium-Sulfur Batteries (Adv. Energy Mater. 24/2017)

Hong-Jie Peng,Jia-Qi Huang,Xin-Bing Cheng,Qiang Zhang

DOI: https://doi.org/10.1002/aenm.201770141

IF: 27.8

2017-01-01

Advanced Energy Materials

Abstract:In article number 1700260, Qiang Zhang and co-workers review high-sulfur-loading Li–S batteries enabled by multiscale hierarchical design principles. How to bridge the ‘sulfur cathode’ and ‘lithium anode’ is the key to fill the gaps for better Li-S batteries. The authors provide new insights into the interfacial reactions, strategies for mesoscale assembly, unique architectures, and configurational innovation in the cathode, anode, and separator in advanced Li-S batteries.

Toward Robust Lithium-Sulfur Batteries Via Advancing Li2S Deposition (vol 15, Pg 7949, 2024)

Correction: Toward robust lithium-sulfur batteries via advancing Li2S deposition.

Toward Robust Lithium-Sulfur Batteries Via Advancing Li2S Deposition

Enhanced catalysis LiS<sub>3</sub> of radical-to-polysulfide interconversion <i>via</i> increased sulfur vacancies in lithium-sulfur batteries

Toward Robust Lithium-Sulfur Battery via Advancing Li2S Deposition

A Novel Strategy for High-Stability Lithium Sulfur Batteries by in Situ Formation of Polysulfide Adsorptive-Blocking Layer

Study on Lithium-Sulfur Batteries

Promoting the Transformation of Li2S2 to Li2S: Significantly Increasing Utilization of Active Materials for High‐Sulfur‐Loading Li–S Batteries

Promoting the Transformation of Li2 S2 to Li2 S: Significantly Increasing Utilization of Active Materials for High-Sulfur-Loading Li-S Batteries

Regulating Li2S Deposition and Accelerating Conversion Kinetics Through Intracavity ZnS Toward Low-Temperature Lithium-Sulfur Batteries.

Electrochemical deposition of Li2S2/Li2S in aprotic Li–S batteries

Towards High Performance Li–S Batteries via Sulfonate‐Rich COF‐Modified Separator

Cathode Nanostructuring and Separator Modification for High-Performance Lithium-Sulfur Batteries

In Situ Synthesis of Organopolysulfides Enabling Spatial and Kinetic Co-Mediation of Sulfur Chemistry

Synergistic Interfacial Optimization for High-Sulfur-Content All-Solid-State Lithium-Sulfur Batteries

Progress on critical cell fabrication parameters and designs for advanced lithium–sulfur batteries

Ferrous Sulfide-Assisted Hollow Carbon Spheres As Sulfur Host for Advanced Lithium-Sulfur Batteries

Li-Ion Intercalating Cathode for Advanced Lithium-Sulfur Batteries

Directing the Lithium–Sulfur Reaction Pathway via Sparingly Solvating Electrolytes for High Energy Density Batteries

Advances in lithium–sulfur batteries based on multifunctional cathodes and electrolytes

Lithium-Sulfur Batteries: Review on High-Loading and High-Energy Lithium-Sulfur Batteries (Adv. Energy Mater. 24/2017)