Abstract:The lamellae deformation and cavitation behavior of annealed isotactic polypropylene during uniaxial stretching are comprehensively investigated by in situ synchrotron small-angle X-ray scattering and wide-angle X-ray scattering. We reveal how lamellae deformation occurs in the time scales of elastic deformation, intralamellar slip, and melting-recrystallization, separated by three critical strains which are only rarely influenced by annealing. Strain I (0.1) marks the end of elastic deformation and the onset of intralamellar slip, beyond which the crystallinity decreases gradually. Strain II (0.45) signifies the start of the recrystallization process, from where the long period in the stretching direction begins to decrease from its maximum and the polymer chains in the crystal start to orient along the stretching direction. The energy required for melting arises from the friction between the fragmented lamellae produced by intralamellar slip. Strain III (0.95) denotes the end of the recrystallization process. Beyond the strain of 0.95, the long period and the crystal size remain nearly unchanged. During further stretching, the newly formed lamellae serve as the anchoring points for polymer chains in the amorphous phase. The extension of the polymer chains in between lamellae triggers the strain hardening behavior. On the other hand, annealing significantly decreases the critical strain for voids formation and increases the voids number but restricts the void size. For those samples annealed at a temperature lower than 90 degrees C, voids are formed between strain II and strain III, and voids are oriented in the stretching direction once they are formed. However, for those samples annealed at a temperature higher than 105 degrees C, voids are formed between strain I and strain II. In this case, voids are initially oriented with their longitudinal axis perpendicular to the stretching direction and then transferred along stretching direction via void coalescence. Additionally, the formation of voids influences neither the critical strains for lamellae deformation nor the final long period, the orientation of polymer chains, or the crystal size. The final long period, the orientation of polymer chains in the crystal, and the crystal size are determined only by the stretching temperature through melting-recrystallization.

Quantitative Characterization of Mechanical Property of Annealed Monolayer Colloidal Crystal.

Study of Elastic Modulus and Yield Strength of Polymer Thin Films Using Atomic Force Microscopy

Surface Engineering of Polymeric Colloidal Crystals by Temperature – Pressure Annealing

Effect of Solvent Annealing on the Tensile Deformation Mechanism of a Colloidal Crystalline Polymeric Latex Film.

Interfacial molecular structure and orientation evolution of the polystyrene under confinement during annealing revealed by sum frequency generation vibrational spectroscopy

Multiscale Structural Characterization of a Smectic Liquid Crystalline Elastomer upon Mechanical Deformation Using Neutron Scattering

Size Dependent Mechanical Properties of Monolayer Densely Arranged Polystyrene Nanospheres.

Effect of annealing on the microphase separated behavior and properties of PDMS–MDI–PEG multiblock copolymer films

Retrospecting the relationship between interlamellar amorphous structure and intrinsic modulus of semicrystalline polymers via in-situ positron annihilation lifetime spectroscopy and in-situ X-ray scattering

Critical Strains for Lamellae Deformation and Cavitation During Uniaxial Stretching of Annealed Isotactic Polypropylene

Mechanical Characterization of Stacked Single‐Crystal of Polyethylene and Monolayer MoSe2

Flash DSC Study on the Annealing Behaviors of Poly(l-Lactide Acid) Crystallized in the Low Temperature Region

Thermal Annealing of Colloidal Monolayer at the Air/Water Interface: A Facile Approach to Transferrable Colloidal Masks with Tunable Interstice Size for Nanosphere Lithography

The Fabrication of PP-nanoparticles Monolayer and the Measurement of Elastic Properties

Probing Into the Annealing Effects on Microstructure and Mechanical Properties of Impact Polypropylene Copolymer With Nodular Crystalline Morphology

Mechanics of an Asymmetric Hard--Soft Lamellar Nanomaterial

Temporal evolution of mechanical properties in PDMS: A comparative study of elastic modulus and relaxation time for storage in air and aqueous environment

Real‐time AFM Study of Lamellar Growth of Semi‐crystalline Polymers

correlations of mechanical properties and microstructural parameters in annealed drawn film of liquid crystalline polymer in situ reinforced PP

Detection and Characterization of Folded-Chain Clusters in the Structured Melt of Isotactic Polypropyl-Ene.

Phase morphology evolution upon melt annealing treatment and corresponding mechanical performance of impact-resistant polypropylene copolymer