Abstract:High/ultra-high temperatures (HT/UHT) in deep strata seriously deteriorate the comprehensive performance (such as weak setting stability, poor suspension stability and excessive filtration loss) of oil-well cement (OWC) slurry due to the degradation and group variation of polymer admixtures (retarder, fluid loss additive, dispersant and suspension stabilizer) with high dosage, seriously endangering the safety and quality of cementing construction. The organic/inorganic hybrid admixtures (especially copolymer grafting onto modified nanoparticle) can effectively suppress the thermal degradation and thinning of traditional copolymer admixtures with chainlike molecular structures and maintain its usage effectiveness at HT/UHT. Whereas, limited by the number of hydroxyl groups and the difficulty in dispersion caused by low hydrophilicity of nanoparticles, the traditional modified method that is the hydrolysis condensation between silane coupling agents containing double bonds and hydroxyl groups on the nanoparticles surface exists common problems of low double bond grafting efficiency and difficulty in controlling. In this study, to overcome the above problems, a novel method was applied to obtain the modified nanosilica with double bonds (NS-V) by the cohydrolysis condensation of tetraethyl orthosilicate (TEOS) and vinyltriethoxysilane (VTES). In addition, the copolymer fluid loss additive (PAADM) was grafted onto the surface of NS-V by free radical copolymerization. Characterization of modified nanosilica indicated the existence of C = C on the surface of modified nanosilica and its particle size was approximately 100 nm. Thermal stability measurement demonstrated the thermal decomposition temperature of PAADM from about 270 degrees C rise to approximately 300 degrees C of grafting copolymer (PAADM) onto NS-V (NS-PAADM). Filtration measurement indicated that the NS-PAADM displayed excellent ability on fluid loss control owing to its adsorption and filling effect, the API fluid loss volume of freshwater and saturated brine OWC slurry with 0.9 % bwoc NSPAADM was less than 50 mL/30 min even cured at 240 degrees C. Moreover, rheological and sedimentation stability measurements demonstrated the addition of NS-PAADM relieved the decrease the viscosity and strengthened the grid structure of OWC slurry at HT/UHT, which alleviated the settlement of solid particles and made the density difference of top/middle/bottom segments of hardened OWC slurry cured at 180 degrees C/100 MPa for 24 h lower than 0.03 g cm-3. In addition, the thickening and mechanical measurements suggested that NS-PAADM promoted cement hydration and improved the early mechanical properties of cement stone.

Nanosilica Interface Graft Copolymer for Improving the Suspension Stability and Filtration Performance of Oil-Well Cement Slurry

Synthesis and Performance of A Self Crosslinkable Acrylate Copolymer with High Compatibility for an Oil Well Cement Modifier

Study on the properties of nano silica modified cement for cementing

Heavy Oil Recovery by Surface Modified Silica Nanoparticle/hpam Nanofluids

Enhancing the Properties of Water-Soluble Copolymer Nanocomposites by Controlling the Layer Silicate Load and Exfoliated Nanolayers Adsorbed on Polymer Chains

Polyanionic cellulose/hydrophilic monomer copolymer grafted silica nanocomposites as HTHP drilling fluid-loss control agent for water-based drilling fluids

Rheological properties and early mechanical strength of oil-well cement modified by hybrid nano-silica and nano-hexagonal boron nitride

Nano-Modified Polymer Gels as Temperature- and Salt-Resistant Fluid-Loss Additive for Water-Based Drilling Fluids

Synthesis and Characterization of Composite Polymer Microspheres Based Nano-Silica for Cementing Fluid Loss Additive

A high temperature resistance and hyper‐dispersed nanoparticle grafted by multi‐monomer via in‐situ polymerization: Preparation, characterization, and its imbibition performance

Influence of Various Nanomaterials on the Rheology and Hydration Kinetics of Oil Well Cement

Preparation and Properties of Allyl Ether-Based Polycarboxylate Superplasticizer with Short-Branched Chains Modified by Nano-Silica

Ultra-Stable Silica Nanoparticles as Nano-Plugging Additive for Shale Exploitation in Harsh Environments

Core–shell structure acrylamide copolymer grafted on nano-silica surface as an anti-calcium and anti-temperature fluid loss agent

An Investigation into PVA Fiber Modified with SiO2 for Improving Mechanical Properties of Oil-Well Cements

The Effect of Polymer Elastic Particles Modified with Nano-Silica on the Mechanical Properties of Oil Well Cement-Based Composite Materials

Preparation and properties of nano-silica hybrid hydrophobic associated polyacrylamide for polymer flooding

Effect of Nano-SiO2, Nano-TiO2 and Nano-Al2O3 Addition on Fluid Loss in Oil-Well Cement Slurry

Rheology, Curing Temperature and Mechanical Performance of Oil Well Cement: Combined Effect of Cellulose Nanofibers and Graphene Nano-Platelets

The Synthesis of Polymeric Nanospheres and the Application as High-Temperature Nano-Plugging Agent in Water Based Drilling Fluid

Effect of Nano-SiO2 on mechanical properties, fluidity, and microstructure of superfine tailings cemented paste backfill