Abstract:There are growing concerns about the stresses created by shielding currents in high field superconducting magnets fabricated from tape conductors leading to reduced performance and lifetime. This paper presents results of stress/strain calculations caused by shielding currents assuming the conductor deformations follow a linear constitutive relation. An anisotropic bulk approximation approach was used to calculate the electromagnetic field distributions in a REBCO high field coil with a stack of pancakes and a large number of turns first, and then the Lorentz force distribution and mechanical response characteristics were studied in the two-dimensional axisymmetric configuration. A new discrete contact mechanical model implemented by the finite element method, which is able to simulate the contact and separation behaviors between adjacent turns during the deformation, was proposed to analyze the distributions of hoop stress, hoop strain, radial stress and radial displacement in the coil. The influences of shielding current on those mechanical responses were obtained by comparing the simulation cases with and without taking shielding current into account. Besides, a continuum bulk mechanical model, which is parallel to the discrete contact mechanical model and treats the pancakes as continuum bulks, was modeled as well in order to understand the influences of different models on the simulation results. Furthermore, we studied the influences of a couple of practical factors (including the n-value, ramp rate, and operating mode of the REBCO coil winding) on the shielding current and hoop stress. A couple of novel and important conclusions were found. (1) Neglecting the shielding current behavior would significantly underestimate the maximum local hoop stress in a REBCO high field coil. (2) The continuum bulk mechanical model is not adequate for the stress analysis of dry-wound high field coils, by which unreasonably large tensile radial stresses could be obtained. (3) The highest local hoop stresses at the fully-charged moment and the fully-discharged moment are located in a certain pancake near the end of the coil winding and the end pancake, respectively. (4) Decreasing the n-value and the ramp rate of the REBCO coil could be two auxiliary ways to suppress the shielding current and maximum local hoop stress in the coil. (5) For the ramp-and-hold operating mode, the REBCO coil experiences the highest stress level at the moment when it right achieves the goal field. (6) The cycling operation of a REBCO high field coil can cause the tape experiencing alternative positive and negative hoop stresses and this may decrease the fatigue life of the tape and then the life of a magnet.

Numerical Modelling of Electromechanical Coupling Behaviors in HTS Coil with Implementation of H Formulation in FE Software

An Advanced Computational Approach for Evaluating Screening-Current-Induced Strain in REBCO HTS Coils Considering Electromagnetic-Mechanical Coupling

A Coupled Electromagnetic-Mechanical Model and Contact Behavior of the Superconducting Coils

3D Modelling of Coupled Electromagnetic-Mechanical Responses in REBCO Coils Involving Tape Inhomogeneity

Numerical Analysis of the Electromechanical Behavior of High-Field REBCO Coils in All-Superconducting Magnets

Electromagnetic-mechanical Coupling Analysis of High-Temperature Superconducting Racetrack Coil

An electromagnetic-thermal-mechanical coupling model of dry-wound HTS coil based on T-A formulation with Neumann boundary condition

Electromagnetic Modeling of REBCO High Field Coils by Theh-Formulation

Modelling the mechanics of 32 T REBCO superconductor magnet using numerical simulation

The Improved Model Based on the H-A Formulation in Large-Scale Hts Magnet

Electromagnetic Modelling Using T-A Formulation for High-Temperature Superconductor (re)ba(2)cu(3)o(x) High Field Magnets

Effective 3-D FEM for Large-Scale High Temperature Superconducting Racetrack Coil

Stress and Strain Analysis of a REBCO High Field Coil Based on the Distribution of Shielding Current

Stress, Strain and Electromechanical Analyses of (re)ba2cu3oxconductors Using Three-Dimensional/two-dimensional Mixed-Dimensional Modeling: Fabrication, Cooling and Tensile Behavior

Temperature evolution and thermoelastic behavior of epoxy-impregnated REBCO HTS composite coils studied using a heat-force bi-directional coupling quench model

Three-dimensional simulation of the coupled electromagnetic-mechanical responses in a no-insulation racetrack coil

Numerical analysis on electromagnetic and mechanical properties of the quasi-isotropic strand

Screening current effect on the stress and strain distribution in REBCO high-field magnets: experimental verification and numerical analysis

3D finite element modelling on racetrack coils using the homogeneous <i>T-A </i>formulation

Stress Analysis of Winding Process, Cooling Down, and Excitation in a 10.7 T REBCO HTS Magnet