Abstract:Bisphenol A dicyanate (BADCy) resin microparticles were prepared by precipitation polymerization synthesis and were homogeneously dispersed in a BADCy prepolymer matrix to prepare a BADCy self-reinforced composites. The active functional groups of the BADCy resin microparticles were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results of an FT-IR curve showed that the BADCy resin microparticles had a triazine ring functional group and also had an active reactive group -OCN, which can initiate a reaction with the matrix. The structure of the BADCy resin microparticles was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the TEM results, the BADCy resin microparticles dispersed in the solvent were nano-sized and distributed at 40-60 nm. However, from the SEM results, agglomeration occurred after drying, the BADCy resin particels were micron-sized and distributed between 0.3 μm and 0.6 μm. The BADCy resin prepolymer was synthesized in our laboratory. A BADCy self-reinforced composite was prepared by using BADCy resin microparticles as a reinforcement phase. This corresponds to a composite in which the matrix and reinforcement phase are made from different morphologies of the same monomer. The DSC curve showed that the heat flow of the microparticles is different from the matrix during the curing reaction, this means the cured materials should be a microscopic two-phase structure. The added BADCy resin microparticles as reaction sites induced the formation of a more complete and regular cured polymer structure, optimizing the cross-linked network as well as increasing the interplay between the BADCy resin microparticles and prepolymer matrix. Relative to the neat BADCy resin material, the tensile strength, flexural strength, compressive strength and impact strength increased by 98.1%, 40.2%, 27.4%, and 85.4%, respectively. A particle toughening mechanism can be used to explain the improvement of toughness. The reduction in the dielectric constant showed that the cross-linked network of the self-reinforced composite was more symmetrical and less polar than the neat resin material, which supports the enhanced mechanical properties of the self-reinforced composite. In addition, the thermal behavior of the self-reinforced composite was characterized by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results of DMTA also establishes a basis for enhancing mechanical properties of the self-reinforced composite.

Bismaleimide and Biobased Limonene Copolymer Microspheres As Reactive Fillers to Fabricate Low-k, High-Toughness Cyanate Ester Resin Composites

Cure of Neat Resins and Properties of Composites for Interpenetrating Polymer Networks from the Novel Bismaleimide and Cyanate Containing Naphthalene

Synchronously Improved Toughness and Dielectric Properties of Cyanate Ester Resins Via Modification with Biobased Poly(n‐phenylmaleimide‐co‐limonene)

Highly Thermal Conductive Benzoxazine‐epoxy Interpenetrating Polymer Networks Containing Liquid Crystalline Structures

High performance low-k and wave-transparent cyanate ester resins modified with a novel bismaleimide hollow polymer microsphere

Toughness and Low Dielectric Cyanate Ester Resin Modified with Polyethersulfones Containing Fluorene and Allyl Units

Study on the Relationships between Microscopic Cross-Linked Network Structure and Properties of Cyanate Ester Self-Reinforced Composites

Synchronously improved wave-transparent performance and mechanical properties of cyanate ester resins via introducing fluorine-containing linear random copolymer

Optimizing the dielectric and mechanical properties of melamine based‐benzoxazine resin by copolymerizing with epoxy resin

Cyanate ester resin based composites with high toughness and thermal conductivity

Properties of Copolymer Modification of Epoxy Resin／Bismaleimide Resin／Cyanate Ester Resin

Branched Fluorine/Adamantane Interfacial Compatibilizer for PBO Fibers/Cyanate Ester Wave-Transparent Laminated Composites

Synthesis of a bismaleimide/cyanate ester copolymer containing phenolphthalein functional group with excellent dielectric properties and thermally stable

Preparation and properties of bismaleimide resin blended with alkynyl-terminated modifiers

Optimization and preparation of an allyl phenoxy-modified bismaleimide resin

UV etched random copolymer membrane coated PBO fibers/cyanate ester wave-transparent laminated composites

Facile and Efficient Synthesis of Heat-Resistant Poly(N-phenylmaleimide-co-limonene) Microspheres Bearing Endocyclic Vinyl Groups Based on Bio-Based Limonene

Understanding of the Modified Bismaleimide Composite with Multifunctional Phthalonitrile and Its Outstanding Mechanical Properties

Molecular design and application of low dielectric bismaleimide resin

High-Performance Bismaleimide Resin with an Ultralow Coefficient of Thermal Expansion and High Thermostability

Enhanced toughness and thermal properties of bismaleimide resin based on the synergistic effect of reactive amino‐terminal poly(phthalazinone ether nitrile sulfone) and bisallyl bearing diphenol group