Abstract:Ultrahigh voltage conversion ratio (VCR) DC-DC boost converters are essential for biomedical, optics, sensing and diagnostics applications. For realizing an ultrahigh VCR, the conventional boost converter would result in a large duty ratio D, a large inductor current $\mathrm{I}_{\mathrm{L}}$ and thus a significantly degradation on power efficiency, and its VCR is limited by the parasitic resistors. Figure 8.10.1 top shows the recently reported hybrid boost converters. The multilevel boost converter (MLBC) has a single inductor at the input, and has the feature of input-series-output-series. Therefore, multilevel boost converters considerably improve the VCR and reduce the device voltage stress with the flying capacitors. However, the MLBC topologies still suffer from the problems of low efficiency and low power density caused by the large $\mathrm{I}_{\mathrm{L}}$. Another topology with multipath boost converters (MPBC) has the feature of input-parallel-output-parallel. The MPBC can effectively reduce the $\mathrm{I}_{\mathrm{L}}$ of each branch by connecting parallel input inductors. But the output-parallel structure does not improve the VCR nor reduce the device voltage stress. To address the above issues, this work presents a hybrid input-parallel output-series high power density ultrahigh-VCR step-up DC-DC converter for electrostatic and piezoelectric actuators used for small-scale flyweight devices. This converter is very challenging due to the low $\mathrm{V}_{\text{IN}}(\lt5 \mathrm{~V})$, high $\mathrm{V}_{\text {OUT }}(\gt100 \mathrm{~V}$), high output power (>200mW) and high power density (volume $\lt10 \mathrm{~mm}^{3}$ and weight $\lt100 \mathrm{mg}$). We use both $\mathrm{mW} / \mathrm{mm}^{3}$ and $\mathrm{mW} / \mathrm{mg}$ for the power density units to emphasize the importance of the size and weight for flying robots.

A Battery to 15~36V Hybrid Boost Converter with 14.4x Max VCR for LED-Lighting

A Battery to 15~36V Hybrid Boost Converter with 14.4x Max VCR for LED-Lighting

Applying Diode-Capacitor Voltage Multiplier to Coupled-Inductor Boost Converter for Novel DC-DC Converter with High Voltage Gain and Low Voltage Stress

8.10 A 5V-to-150V Input-Parallel Output-Series Hybrid DC-DC Boost Converter Achieving 76.4mW/mg Power Density and 80% Peak Efficiency

An Improved Boost-Type Hybrid Converter with Multiple Outputs

High Step-Up/Down Switched-Capacitor Based Bidirectional DC-DC Converter

A Three Phase Interleaved Boost Converter with L & C Voltage Extension Mechanism

A 5V Input 98.4% Peak Efficiency Reconfigurable Capacitive-Sigma Converter with Greater Than 90% Peak Efficiency for the Entire 0.4~1.2V Output Range.

High Frequency Multicell Cascaded Quasi-Square-Wave Boost Converter

A Hybrid ZVS Full-Bridge Converter with Transformer Winding Series-Parallel Auto Regulated Current Doubler Rectifier

A 36-55 V Input 0.6-2.5 V Output Bypass-Assist Series-Capacitor Power Converter with 93.1% Peak Efficiency and 1.5 Ma-5 A Load Range.

A New Modified Quadratic Boost Converter with High Voltage Gain

A High Efficiency Transformerless Step-Up DC-DC Converter with High Voltage Gain for LED Backlighting Applications

A Soft-Switched Boost Converter Based LED Driver With Reduced Input Current Ripple

Transformer-Less Soft-Switching High-Gain PWM Boost Converter With Reduced Components and Increased Effective Duty Cycle

An ultra-high gain boost converter with low switching stress for integrated multi-energy storage systems

A New Combined Boost Converter with Improved Voltage Gain as a Battery-Powered Front-End Interface for Automotive Audio Amplifiers

Single-Phase Improved Active Clamp Coupled-Inductor-Based Converter with Extended Voltage Doubler Cell

A Dual Path Hybrid Step-Up Converter with Enhanced Drive Voltage for Low Voltage Applications

A Green-Switch Controller IC for Cascade Buck-Boost Converter with Seamless Transition over Entire Input and Load Range.

A High-Efficiency DC/DC Converter for High-Voltage-Gain, High-Current Applications