Modeling and Measurements of Creep Deformation in a Ceramic Fiber Reinforced Metal Matrix Composite

Xu Kong,Yumin Wang,Qing Yang,Rui Yang

DOI: https://doi.org/10.2139/ssrn.4779296

IF: 11.322

2024-01-01

Composites Part B Engineering

Abstract:Download This Paper Open PDF in Browser Add Paper to My Library Share: Permalink Using these links will ensure access to this page indefinitely Copy URL Copy DOI

What problem does this paper attempt to address?

Dynamic Densification of Metal Matrix-Coated Fibre Composites: Modelling and Processing

H Peng,FPE Dunne,PS Grant,B Cantor

DOI: https://doi.org/10.1016/j.actamat.2004.10.015

IF: 9.4

2005-01-01

Acta Materialia

Abstract:The consolidation processing of Ti–6Al–4V matrix-coated fibre (MCF) composite under vacuum hot pressing (VHP) has been investigated. A new test methodology has been developed for the determination of in situ matrix coating creep properties. In using the methodology, only a single, simple test is required, together with finite element modelling of the single fibre compression test. The creep coefficient and stress index have been determined for electron beam evaporated physical vapour deposited Ti–6Al–4V at 900 °C to be 1.23×10−5 and 1.3, respectively. Consolidation experiments have been carried out on multi-ply MCF arrays under vacuum hot pressing. Finite element models have been developed for the dynamic consolidation of both square and hexagonal fibre packings. The creep constants for the Ti–6Al–4V, determined using the single fibre test, were assigned to the coating in the finite element models. Excellent agreement between predicted and experimental results was achieved, providing verification of the single fibre test methodology for the determination of creep constants.
Modeling of the influence of fibers on creep of fiber reinforced cementitious composite

Jun Zhang

DOI: https://doi.org/10.1016/S0266-3538(03)00160-X

IF: 9.1

2003-01-01

Composites Science and Technology

Abstract:An analytical model has been developed to study the influence of fibers on creep of fiber reinforced cementitious composites. The model is based on the assumption that shear stress is produced between fiber and surrounding matrix as the matrix deforms. This shear stress in turn influences the matrix creep behavior resulting in macroscopic creep strain lower than that of pure cement-based matrix. In the present paper, a creep strain expression in the form of matrix creep strain multiplying by a fiber influence factor, which reflects the influences of matrix and fiber properties as well as fiber orientation characteristics, is presented. A parametric study, including the influence of elastic moduli of fiber and matrix, fiber dimension and fiber content is carried out. The modeling results indicate that creep strain of fiber reinforced cement-based composite is significantly influenced by the elastic moduli of fiber and matrix as well as fiber length and thickness (i.e. diameter for fiber with circular cross-section). Model predictions compare favorably with experimental measurements of creep strain of fiber reinforced mortar and concrete under compressive load.
Creep-fatigue and Cyclically Enhanced Creep Mechanisms in Aluminium Based Metal Matrix Composites

Dario Giugliano,Daniele Barbera,Haofeng Chen,Nak-Kyun Cho,Yinghua Liu

DOI: https://doi.org/10.1016/j.euromechsol.2018.10.015

IF: 4.873

2018-01-01

European Journal of Mechanics - A/Solids

Abstract:An aluminium (Al, 2024T3) matrix composite reinforced with continuous alumina (Al2O3) fibres is investigated under tensile off-axis constant macro stress and thermal cyclic loading. The micromechanical approach to modelling and three different fibre cross-section geometries have been employed. The effect of creep is included by considering three dwell times at the peak temperature of the thermal loading history. The presence of the hold time gives rise to different sources of failure such as cyclic enhanced creep and creep ratchetting. These failure mechanisms are carefully discussed and assessed. The linear matching method framework has been used for the direct evaluation of the crucial parameters for creep-fatigue crack initiation assessment at the steady cycle. A detailed representation of the steady-state hysteresis loops is provided by using the strain range partitioning and a method for dealing with multiaxiality is reported with regard to the algebraic sign of the Mises-Hencky equivalent stress and strain. All the results obtained have been benchmarked by fully inelastic step-by-step (SBS) analyses. The design of a long fibre metal matrix composite should consider not only the detrimental effect of their dissimilar coefficient of thermal expansion, but also the state of stress at the interface between the matrix and fibre.
Research and Development of Creep of Metal Matrix Composites

田君,李文芳,韩立发,彭继华

2010-01-01

Abstract:Research development on high temperature creep of metal matrix composites at home and abroad are summarized.The three theoretical models of the creep theory studies are focused on analyzing,and the core issue of theoretical studies is a mechanism of the dislocation over the second phase and the threshold stress sources.Characte-ristics of various experimental methods of the current creep experimental studies are recounted.Advantages of the computer finite element analysis in creep studies are discussed.The research trends and development on high temperature creep of metal matrix composites in China are presented.
CREEP BEHAVIOR OF SHORT ALUMINA FIBER REINFORCED Al BASED COMPOSITE

黄明华,王浩伟

DOI: https://doi.org/10.3321/j.issn:1000-3851.2004.05.002

2004-01-01

Abstract:The constant stress creep behavior at 350 ℃ was investigated for Al_2O_3 fiber reinforced Al based composite fabricated by squeeze casting. During the interrupted creep process, the variations of microstructure were observed by means of SEM. The fracture of fibers, the debonding of fiber and matrix, and the deformation of matrix were found in creep of composite materials. On the basis of the changes of microstructure in three phases of creep, the creep behavior of the composite was analyzed. It is suggested that the glide and climb of dislocation around fibers contribute to creep of the composite.The authors propound a rupture mechanism of short fiber reinforced MMCs, which succeeds in interpreting the three stages of creep for composites.
Modeling creep behavior of carbon nanotube/fiber/polymer composite cylinders

Ahmad Reza Ghasemi,Komeil Hosseinpour,Masood Mohandes

DOI: https://doi.org/10.1177/2397791418768576

2018-04-12

Abstract:In this research, the effects of multi-walled carbon nanotubes on the distribution of long-term creep strains in thick-walled multi-walled carbon nanotube/fiber/polymer three-phase laminated composites are studied. In the first step, micromechanical models are developed to calculate the elastic properties of multi-walled carbon nanotube/vinylester and multi-walled carbon nanotube/E-glass fiber/vinylester composites. Using classical lamination plate theory, equilibrium and compatibility equations and strain–displacement relations, the distribution of effective stresses is considered. Moreover, utilizing Schapery single-integral model for nonlinear viscoelastic materials, Prandtl–Reuss relations and Mendelson’s approximation method, not only the distribution of circumferential and radial strains is investigated but also the effects of fiber orientation and weight fraction (wt.%) of the multi-walled carbon nanotubes on the way of distribution are studied. The results demonstrated that the addition of the multi-walled carbon nanotube to the vinylester can reduce absolute values of the radial and circumferential creep strains and dimensionless effective stresses. Moreover, most reduction occurred in the inner wall of the cylindrical shell when fiber orientation was α = 90°.
Modeling of Fiber Toughening in Fiber-reinforced Ceramic Matrix Composites

Gui-ming SONG,Yu ZhOU,Yi SUN

DOI: https://doi.org/10.3969/j.issn.1006-2793.1999.01.014

1999-01-01

Abstract:A fiber toughening model of fiber reinforced ceramic matrix composites is performed.The constitutive equation is obtained through micromechanical considerations based on two kinds of fiber toughening mechanisms,crack bridging and fiber pullout.The calculated results of 50%SiC f/LAS composites show that the R curve and load/crack tip opening displacement curve exhibit notable nonlinear behaviors,and crack bridging is the dominant toughening mechanism in this kind of ceramics.Calculated toughness is in good agreement with experimental results.
On the Creep Fatigue Behavior of Metal Matrix Composites

D. Barbera,H. F. Chen,Y. H. Liu

DOI: https://doi.org/10.1016/j.proeng.2015.12.277

2015-01-01

Procedia Engineering

Abstract:The mechanical behaviour of Metal Matrix Composites (MMCs) subjected to a high temperature and cyclic load condition is difficult to understand. The significantly differing coefficients of thermal expansion between ceramic and metal give rise to micro thermal stresses. Their performance under varying load and high temperature is complex and inconsistent, where fatigue and creep damages become the main failures of MMCs. To improve current understanding of the relationship between creep fatigue interaction of MMCs, the history of thermal and mechanical loading, and the creep dwell period, a highly accurate but robust direct simulation technique on the basis of the Linear Matching Method (LMM) framework has been proposed in this paper, and been applied to model the fatigue and creep behaviour of MMCs. A homogenised FE model is considered in all analyses, which consist of continuous silicon carbide fibres embedded in a square 2024T3 aluminium alloy matrix array. Various factors that affect creep and fatigue behaviours of composites are analysed and discussed, including effects of the applied load level, dwell period and temperature on the MMC's performance. The effects of reversed plasticity on stress relaxation and creep deformation of MMC are investigated, and the behaviours of cyclically enhanced creep and elastic follow-up are presented. The applicability and accuracy of the proposed direct method has also been verified by the detailed step-by-step analysis via Abaqus.
Experimental Study and Mesoscale Finite Element Modeling of Elastic Modulus and Flexural Creep of Steel Fiber-Reinforced Mortar

Siming Liang,He Du,Yuhang Liu,Yuxuan Chen,Jiankun Liu,Ya Wei

DOI: https://doi.org/10.1016/j.conbuildmat.2022.129875

IF: 7.4

2022-01-01

Construction and Building Materials

Abstract:Incorporation of fiber into cementitious materials would affect their mechanical and creep properties. The macro creep test is normally time-consuming and is difficult to evaluate the influence of the microstructures fully. This study investigated experimentally the elastic modulus and flexural creep of mortars with different volume fractions of steel fibers. Then a mesoscale finite element (FE) model consisting of mortar and randomlydistributed steel fibers was developed. The results show that the elastic modulus of mortars increases with increasing volume fraction of steel fiber, but the specific flexural creep exhibits an opposite trend. The influence of volume fraction of steel fiber on the specific flexural creep is more significant than that on the elastic modulus. The mesoscale FE model developed in this study is capable of capturing well the development of elastic modulus and flexural creep of mortars with different volume fractions of steel fibers. The simulated results reveal that fiber orientation is an important factor affecting the elastic modulus and flexural creep of steel fiber-reinforced mortars. The flexural creep (elastic modulus) of steel fiber-reinforced mortar increases (decreases) with increasing fiber rotational angle with respect to the stress direction. Moreover, both the elastic modulus and flexural creep of the mortar containing randomly-distributed steel fibers are equivalent to those of the mortars with steel fibers distributed by a fixed rotational angle of 30 degrees when the volume fraction of steel fiber ranges from 1% to 3%. The findings in this study are expected to provide references to further investigations of elastic and creep properties of fiber-reinforced cementitious materials.
Long‐term creep deformation of carbon fiber/epoxy composites with physical aging: Experimental investigation and constitutive modeling

Jiangyan Yang,Xiaofei Ma,Hui Wang,Fulin Shang,Demen Hou

DOI: https://doi.org/10.1002/pc.27964

IF: 5.2

2023-12-10

Polymer Composites

Abstract:Tensile Creep Testing of CF/EP Composites and Structural‐Level Flexural Creep Testing. The tensile creep tests for two kinds of epoxy resin matrix composite laminates were performed under 25°C and 50°C. Results indicate that these materials deform in a time‐dependent manner, that is, the tensile strain increases within a short time after the tests began, and then decreases during most of the loading period. Such increase and decrease trends reflect the creep characteristic and effect of physical aging, respectively. A linear viscoelastic model is developed to include both the creep temperature effect and physical aging effect, starting from the Boltzmann superposition principle. In modeling, these two effects both contribute to the transient compliance and result in the increase and decrease of the transient compliance. Time–temperature/aging time superposition principle is adopted to deal with the influences of temperature and physical aging. This theoretical model is further implemented numerically within a finite element framework. To verify the newly proposed model, not only the experimental and numerical results of the tensile deformations of laminates are compared, but also the bending deformations of structural components made from the above laminates are analyzed. Highlights Tensile creep tests were done for carbon fiber/epoxy laminates. The strain shows creep temperature and aging effect (TE and AE). New constitutive relation was proposed to describe the TE‐ and AE‐caused strains. Structural‐level flexure creep tests and simulation analyses were conducted.

materials science, composites,polymer science
Experiment and mesoscopic modelling on the dynamic compressive behaviors of a new carbon fiber-reinforced cement-based composite

Zhangyu Wu,Jinhua Zhang,Hongfa Yu,Haiyan Ma,Hao Wang,Guijia Zhang,Bing Yan

DOI: https://doi.org/10.1016/j.cemconcomp.2022.104519

IF: 9.93

2022-07-01

Cement and Concrete Composites

Abstract:This paper presents an experimental and numerical study on the compressive behaviors of a new carbon fiber-reinforced cement-based composite (CFRCC) that is composed of magnesium oxysulfate cement, carbon fiber and some chemical admixtures. Parametric studies on the effects of carbon fiber content and strain rate on the compressive behaviors of CFRCC, were conducted using a series of quasi-static and dynamic compressive tests. The research items includes the failure morphology, stress-strain curve, dynamic increase factor (DIF), etc. Besides, a three-dimensional (3D) mesoscale modelling approach was proposed to simulate and analyze the mechanical responses and the failure mechanisms of CFRCC subjected to dynamic compressive loading, where the random dispersion of chopped fibers were realistically considered. The results indicate that the cracking and failure modes of CFRCC were significantly affected by the bridging effect of carbon fibers randomly dispersed in cement matrix. With the increase of fiber content, the dynamic peak stress and peak strain of CFRCC at similar strain rates showed an increasing and decreasing trend, respectively. An evident strain-rate hardening effect could be found on the initial elastic modulus and the peak stress of CFRCC as well. While the relationship between the DIF of CFRCC and the logarithm of strain rate could be described using a quadratic function. Moreover, the mesoscale modelling approach has been validated by a good agreement between the numerical and tested results, demonstrating the feasibility of the developed mesoscale model in simulating and investigating the dynamic behaviors of CFRCC. All in all, the CFRCC has proven to be of great significance in resisting to impact loads, and more insights should be provided into its dynamic properties.

construction & building technology,materials science, composites
Modeling of Fiber Toughening in Fiber-Reinforced Ceramic Composites

GM Song,Y Zhou,Y Sun

DOI: https://doi.org/10.1016/s0272-8842(98)00033-9

IF: 5.532

1999-01-01

Ceramics International

Abstract:A fiber toughening model of fiber-reinforced ceramic matrix composites is presented. The constitutive equation is obtained through micromechanical considerations based on two kinds of fiber toughening mechanisms, crack bridging and fiber pullout. The calculated results show that two different zones in the R-curve and Load/displacement curve exhibit notable nonlinear behavior. Calculated toughness of 50vol%SiCf/LAS composites is in good agreement with experimental results.
Modeling Long-Term Creep and Physical Aging Behavior of Carbon/Epoxy Composites Based on Coupling Model

Jiangyan Yang,Xiaofei Ma,Hui Wang,Fulin Shang,Demen Hou

DOI: https://doi.org/10.1142/s1758825124500297

IF: 3.5

2024-02-15

International Journal of Applied Mechanics

Abstract:International Journal of Applied Mechanics, Ahead of Print. Our previous study observed a non-monotonic time-dependent deformation from the long-term isothermal tensile creep tests, indicating the significant influence of physical aging on viscoelastic behavior. In this work, a new physical mechanism-based thermo-rheological complex constitutive relation that combines Ngai's coupling model and Schapery's nonlinear viscoelastic framework is established. A piecewise function was used to represent the non-monotonic time-varying compliance, in which molecular cooperativity and the interaction between different relaxing units were considered. The strength of the interaction is presented by a coupling strength parameter. The effects of stress and temperature on the deformation are represented by not only two shift factors but also are associated with the coupling strength parameter, which is modeled as a function of the fictive temperature. The physical aging effect is also incorporated into the evolution of the fictive temperature. The proposed model was verified by a comparison of the experimental and finite element simulated results. Finally, the physical meanings of the model parameters and their correlation with the macroscopic deformation of the laminates were discussed.

mechanics
Flexural Creep Tests and Long-Term Mechanical Behavior of Fiber-Reinforced Polymeric Composite Tubes

Zengqin Yang,Hui Wang,Xiaofei Ma,Fulin Shang,Yu Ma,Zhenwei Shao,Demen Hou

DOI: https://doi.org/10.1016/j.compstruct.2018.03.083

IF: 6.3

2018-01-01

Composite Structures

Abstract:An experimental investigation of the long-term creep behavior of fiber reinforced polymeric composite tubes subjected to flexural loading was performed. The tubes were first tested under a three-point bending scheme at room temperature to determine the ultimate flexural strength (UFS) and to identify the characteristic failure mode and possible failure locations. Creep tests were then carried out at stress levels of 45%, 55%, 65%, and 75% of the UFS at constant temperatures ranging from -60 degrees C to 100 degrees C for 500 h, and strain measurements over time were recorded. The tubes were further tested at varying temperatures by applying 22.5 thermal cycles between -60 degrees C and 100 degrees C and 9.5 thermal cycles between -160 degrees C and 80 degrees C. Similar flexural loads were applied simultaneously on the tubes. Long-term creep deformation of the tube was evaluated using the time-temperature-stress superposition principle, the derived creep main curves, and the Findley model. Finally, the creep deformation and mechanical strength of the tube at expected service conditions over its entire lifetime were predicted.
The importance of damage and slow crack growth in the creep behavior of ceramic matrix composites

J. Chermant,G. Boitier

DOI: https://doi.org/10.1163/156855199X00083

Abstract:Three ceramic matrix composites (CMCs) were investigated after creep tests: a 2D SiCf-MLAS, a 2D SiCf-SiC and a 2.5D Cf-SiC. The damage features of each one are identified, using optical and scanning electron microscopies (SEM), and the complete damage sequences are presented. As a result of its time-dependence, damage in CMCs may be considered as slow crack growth in the temperature and stress fields investigated. But the quantification of damage, through the classical damage mechanics, appears as a complex issue, due to the architecture effects in composite materials.

Engineering,Materials Science
Micro-creep Behavior and Microstructure Evolution of SiCp/2024Al Composite

Deng Gong,Youfang Cao,Yuli Zhan,Xin Liu,Jingtao Guan,Longtao Jiang,Pengchao Kang,Zhenhe Yu,Murid Hussain,Gaohui Wu

DOI: https://doi.org/10.1016/j.msea.2019.138606

2020-01-01

Abstract:The micro-creep behavior of metal matrix composite for inertial instrumentation was studied in this work. The interface, defect state and precipitation behavior during micro-creep were focused. The strain-time and strain rate-time relationships for SiCp/2024Al were investigated in-depth. The stress exponent and activation energy were measured 3 and 34.0 kJ/mol, respectively. It was found that the dislocation viscous slip dominates micro-creep mechanism. Moreover, the influence of load on precipitation behavior and the evolution of micro-creep microstructure were also discussed.
Study on creep characteristics and damage evolution of surrounding rock and filling body (SR-FB) composite specimens

Jianxin Fu,Bangyi Zhang,Yuye Tan,Jie Wang,Weidong Song

DOI: https://doi.org/10.1016/j.jmrt.2023.02.132

IF: 6.267

2023-03-08

Journal of Materials Research and Technology

Abstract:To study the structural parameter influence on the creep mechanical properties of surrounding rock and filling body (SR-FB) composite specimens, reveal their creep energy change laws and damage evolution characteristics, the composite specimens with different inner diameters (12 mm, 18 mm, 24 mm, or 30 mm) were prepared, conventional triaxial tests and triaxial creep tests were carried out. Besides, Computed tomography (CT) scanning was used to analyze the internal crack growth before loading and after creep failure. The results show that with the increase of inner diameters, the SR-FB creep deformation increased, peak strengths decreased from 87.42 MPa to 60.60 MPa, long-term strengths decreased from 69.10 MPa to 48.35 MPa, and the steady-state creep rate increased exponentially. The three-dimensional reconstruction shows that with the increase of inner diameters, the SR-FB failure modes were transformed from single slope shear failure to tension-conjugate shear failure, and the internal cracks significantly increased. Furthermore, the creep energy and damage development of SR-FB were nonlinear related to the inner diameter and stress level. An improved creep damage constitutive model considering inner diameter and stress level was established, which can better characterize the whole creep process of SR-FB.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Experimental and Numerical Investigation of Creep Behavior In Isotropic Composites

Mohsin Jaber Jaweej,Mohsin A. Abdulhussein,Bashar kassim Zalzala

DOI: https://doi.org/10.31026/j.eng.2014.01.05

2023-04-05

Journal of Engineering

Abstract:Creep testing is an important part of the characterization of composite materials. It is crucial to determine long-term deflection levels and time-to-failure for these advanced materials. The work is carried out to investigate creep behavior on isotropic composite columns. Isotropy property was obtained by making a new type of composite made from a paste of particles of carbon fibers mixed with epoxy resin and E-glass particles mixed with epoxy resin. This type of manufacturing process can be called the compression mold composite or the squeeze mold composite. Experimental work was carried out with changing the fiber concentration (30, 40 and 50% mass fraction), cross section shape, and type of composite. The creep results showed that the higher the fiber concentration, the more the creep resistance. Type of fiber plays a very critical role, where carbon/epoxy composite showed much higher creep resistance and also showed much higher modulus of elasticity than the E-glass/epoxy composite. Specimen shape factor noticed to play a very small role. However, square cross sectional area showed slightly higher resistance for creep than the rectangular cross sectional area. This difference is not critical and can be ignored. F.E.M simulation with ANSYS Inc. software was implied and results were compatible with the experimental work with a maximum discrepancy of (17.24%).
Molecular dynamics investigation on the interfacial shear creep between carbon fiber and epoxy matrix

Lik-ho Tam,Jinqiao Jiang,Zechuan Yu,John Orr,Chao Wu

DOI: https://doi.org/10.1016/j.apsusc.2020.148013

IF: 6.7

2021-01-01

Applied Surface Science

Abstract:<p>Carbon fiber-reinforced polymer (CFRP) composite is subject to external loads during service life, suffering the interfacial creep between the fiber and the matrix and eventually the interfacial slippage. CFRP composite loses the interfacial integrity due to the interfacial creep and the long-term durability is weakened. In order to understand the degradation, microscopic details of interfacial structural changes during the creep are essential. This study aims to investigate microscopic creep behavior of a carbon fiber/epoxy interface at different shear load levels using molecular dynamics simulations. A molecular interface model consisting of an epoxy molecule bonded to graphite sheets representing the fiber outer layer is constructed, which is validated by comparing the mass density, glass-transition temperature and Young's modulus of bonded epoxy with experimental measurements. According to the creep simulation, there is a threshold stress for the onset of creep failure, above which the interface detaches. Comparatively, no interfacial detachment occurs under the low stress regime, where the displacement–force curve is plotted and used to quantify the energy barrier to the onset of creep failure. Meanwhile, the strain and stress evolution of the interface are correlated to interfacial structural changes to understand the interfacial creep mechanism. This study provides molecular insights into the interfacial creep behavior in the fiber/matrix system and form the basis of multiscale investigation framework on the interfacial creep behavior.</p>

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Effect of fiber coating on creep behavior of SiC fiber-reinforced titanium aluminide matrix composites

Hsing-Pang Chiu,J-M. Yang,J.A. Graves

DOI: https://doi.org/10.1557/jmr.1994.0198

IF: 2.7

1994-01-01

Journal of Materials Research

Abstract:The effect of fiber coating on the creep behavior and damage mechanisms of unnotched SCS-6 fiber-reinforced Ti3Al matrix composites under longitudinal and transverse loading was investigated at 700 °C. Stresses ranging from 700 to 900 MPa and 200 to 400 MPa were used for longitudinal and transverse loading, respectively. An Ag/Ta duplex layer was coated onto the SCS-6 fiber prior to consolidation via physical vapor deposition. The microstructure of the crept composites was examined to determine the creep deformation mechanisms. The creep cracking behavior of the notched composites was also studied at initial stress intensity factors, K i , ranging from 15 to 20 MPa-m 1/2 . Microstructural observation revealed that multiple fiber fracture (at low to medium stress levels), microcracking along the reaction zone/matrix interface (at medium stress levels), and matrix cracking extending from the broken fiber ends (at high stress levels) were the major damage mechanisms during quasi-steady state creep under longitudinal loading. The results show that the Ag/Ta duplex coating significantly improved the creep resistance and flexural strength of the composite under transverse loading. The Ag/Ta duplex coating was also shown to significantly prolong the creep rupture life of SiC fiber-reinforced Ti 3 Al composites.

materials science, multidisciplinary

Modeling and Measurements of Creep Deformation in a Ceramic Fiber Reinforced Metal Matrix Composite

Dynamic Densification of Metal Matrix-Coated Fibre Composites: Modelling and Processing

Modeling of the influence of fibers on creep of fiber reinforced cementitious composite

Creep-fatigue and Cyclically Enhanced Creep Mechanisms in Aluminium Based Metal Matrix Composites

Research and Development of Creep of Metal Matrix Composites

CREEP BEHAVIOR OF SHORT ALUMINA FIBER REINFORCED Al BASED COMPOSITE

Modeling creep behavior of carbon nanotube/fiber/polymer composite cylinders

Modeling of Fiber Toughening in Fiber-reinforced Ceramic Matrix Composites

On the Creep Fatigue Behavior of Metal Matrix Composites

Experimental Study and Mesoscale Finite Element Modeling of Elastic Modulus and Flexural Creep of Steel Fiber-Reinforced Mortar

Long‐term creep deformation of carbon fiber/epoxy composites with physical aging: Experimental investigation and constitutive modeling

Experiment and mesoscopic modelling on the dynamic compressive behaviors of a new carbon fiber-reinforced cement-based composite

Modeling of Fiber Toughening in Fiber-Reinforced Ceramic Composites

Modeling Long-Term Creep and Physical Aging Behavior of Carbon/Epoxy Composites Based on Coupling Model

Flexural Creep Tests and Long-Term Mechanical Behavior of Fiber-Reinforced Polymeric Composite Tubes

The importance of damage and slow crack growth in the creep behavior of ceramic matrix composites

Micro-creep Behavior and Microstructure Evolution of SiCp/2024Al Composite

Study on creep characteristics and damage evolution of surrounding rock and filling body (SR-FB) composite specimens

Experimental and Numerical Investigation of Creep Behavior In Isotropic Composites

Molecular dynamics investigation on the interfacial shear creep between carbon fiber and epoxy matrix

Effect of fiber coating on creep behavior of SiC fiber-reinforced titanium aluminide matrix composites