Abstract:Considering the demand for a more environmentally friendly system, renewable and sustainable energy sources, such as wind and solar power are regarded as a promising substitute for fossil fuels in the generation of electricity. Since these energy sources exhibit intermittency and unpredictability, there is a need to develop a highly efficient and rapidly responsive energy conversion system for the purpose of storing this energy as a chemical fuel. Due to their ability to manage the variability of intermittent energy sources, proton exchange membrane electrolyzer cells (PEMECs) are garnering considerable interest. However, their broad commercial adoption is hindered by their relatively modest performance and elevated costs. PEM electrolysis is a promising technology for generating substantial quantities of hydrogen from surplus electricity generated by renewable sources. Nonetheless, the expense of the electrolyzer stack arises primarily from the metallic bipolar plates, because it possesses heavy weight and expensive precious metal coatings. Significant efforts have been performed on the development of titanium-based bipolar plates, but it has high base material and fabrication cost. In recent years, there has been a substantial focus on stainless steel bipolar plates for PEM electrolyzer application. Stainless steel can serve as an alternative, but it requires a coating to enhance its anti-corrosion properties. Electroplated chromium coatings exhibit favorable mechanical characteristics and find extensive application in precision mechanical components such as molds and surgical instruments. Their outstanding wear resistance, high hardness, impressive corrosion resistance, and glossy finish make them appropriate for many other applications, including both decorative and functional coatings. As a result, chromium electroplating has emerged as one of the most extensively employed techniques within the electroplating sector. The dense pack chromium layer is prepared on a 316L stainless steel substrate to enhance the anti-corrosion property and electronic conductivity. Herein, the role of gold striking underlayer, and thick chromium coating is studied for preparing the anti-corrosive stainless steel bipolar plates. First, a gold striking film as an underlayer on the stainless-steel substrate is electroplated to passivate the chromium-based oxides. Further, a thick and dense chromium layer is deposited on the gold underlayer by electroplating. The electroplating bath is operated using platinized titanium felt as an anode and 316L stainless steel as a working electrode without the separation of anodic and cathodic compartments. The electroplating solution is consisting of Cr (VI) oxide and H 2 SO 4 (pH = 2). The nanocrystalline chromium coating with a thickness of approximately 2 μm is bright and uniform. Furthermore, gold as a protective layer of thickness approximately 1 μm is coated by electroplating on the chromium surface. The Cr and Au/Cr coatings are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron microscopy (XPS) analysis. Subsequently, the protective layer-coated substrates were analyzed in a simulated PEM electrolyzer environment, and these coatings facilitated promising protective properties on the stainless-steel substrate. The corrosion testing was carried out in 0.5 M H 2 SO 4 + 2 ppm HF solution at 70 0 C purged with oxygen. The stable passive film and high corrosion resistance were obtained by gold striking underlayer and chromizing the 316L stainless steel substrate. As a result, the potentiodynamic polarization analysis showed the corrosion current density of 0.84 μA/cm 2 for the Au/Cr-Au underlayer sample in a simulated operating environment. In contrast, the absence of the gold striking underlayer between Cr and stainless steel causes the pitting corrosion. The Au/Cr coating is tested in an acidic corrosion media for a long duration of 24 hours and it showed lower degradation as compared to without gold striking underlayer and without Cr film. The findings presented in this study illustrate the feasibility of employing stainless steel as the foundational material for the bipolar plate of a PEM electrolyzer.

Towards cost-effective and durable bipolar plates for proton exchange membrane electrolyzers: A review

Review on bipolar plates for low‐temperature polymer electrolyte membrane water electrolyzer

Cheap and stable bipolar plates

Effect of bipolar-plates design on corrosion, mass and heat transfer in proton-exchange membrane fuel cells and water electrolyzers: A review

Comparative review of corrosion-resistant coatings on metal bipolar plates of proton exchange membrane fuel cells

Design and Development of Coating for Metallic Bipolar Plates in Proton Exchange Membrane Fuel Cell (PEMFC): A Review

Process and challenges of stainless steel based bipolar plates for proton exchange membrane fuel cells

Low-Cost Bipolar Plates of Ti4O7-Coated Ti for Water Electrolysis with Polymer Electrolyte Membranes

A novel PEMEC with 3D printed non-conductive bipolar plate for low-cost hydrogen production from water electrolysis

Research Progress and Prospect of the Materials of Bipolar Plates for Proton Exchange Membrane Fuel Cells (Pemfcs)

Highly Conductive and Corrosion-Resistant NbN Coatings on Ti Bipolar Plate for Proton Exchange Membrane Water Electrolysis

Research Progress and Prospects of Bipolar Plate Materials for Proton Exchange Membrane Fuel Cells

Bipolar plate development with additive manufacturing and protective coating for durable and high-efficiency hydrogen production

Research Progress in Surface Modification of Metal Bipolar Plates for Proton Exchange Membrane Fuel Cells

Low-cost Porous Transport Layers for Water Electrolysis Cells with Polymer Electrolyte Membranes

Development of Novel Coating on Metallic Bipolar Plates for Proton Exchange Membrane Water Electrolyzer Application

Bipolar Plate Design Assessment: Proton Exchange Membrane Fuel Cell and Water Electrolyzer

Design Principle and Regulation Strategy of Noble Metal‐Based Materials for Practical Proton Exchange Membrane Water Electrolyzer

Materials and Preparation of Bipolar Plates in PEMFC

Design and manufacturing of stainless steel bipolar plates for proton exchange membrane fuel cells

Towards mass applications: A review on the challenges and developments in metallic bipolar plates for PEMFC