Abstract:Highly efficient and stable, rigid and flexible p‐i‐n perovskite solar cells are developed by incorporating a 2‐(acetyloxy)‐N,N,N‐trimethylethanium chloride additive into the lead iodide precursor solution to prepare a porous PbI2 layer. The good diffusion of the organic ammonium salt results in flat and dense perovskite film with large particle size, which achieves high power conversion efficienciesPCE of 23.40% (rigid) and 21.10% (flexible) with excellent ambient and mechanical stability. Flexible perovskite solar cells (FPSCs) are attracting widespread research and attention for their benefits as the next‐generation wearable electronic products. However, there are still many challenges in the quest to achieve dense, pinhole‐free, high crystal quality, low defect, and stable perovskite films, which limit further improvement in the efficiency and stability of FPSCs. Herein, a novel technique for the incorporation of quaternary ammonium halide (QAH) additives to prepare fluffy porous lead iodide layers by using a two‐step sequential deposition method, is reported. Benefiting from the good diffusion of organic amine salts on porous PbI2 layers, flat and dense perovskite films are produced with large particle sizes, few defects, and high crystal quality. Finally, the champion rigid and flexible p‐i‐n PSCs with the 2‐(acetyloxy)‐N,N,N‐trimethylethanium chloride (AtaCl) additive achieves exciting power conversion efficiencies (PCE) of 23.40% and 21.10%, respectively. The device with the AtaCl additive retains over 90% of its original PCE under ambient conditions (40 ± 5% relative humidity (RH)) over 1000 h of aging without encapsulation. In addition, the flexible device with the AtaCl additive shows excellent stability under mechanical bending conditions, retaining ≈85% of its original PCE after 10 000 cycles (bending radius = 5 mm).

25% - Efficiency Flexible Perovskite Solar Cells Via Controllable Growth of SnO2

SnO2 Surface Modification and Perovskite Buried Interface Passivation by 2,5‐Furandicarboxylic Acid for Flexible Perovskite Solar Cells

Active SnO2 Crystal Planes Enable Efficient and Ultra‐Bendable n‐i‐p Perovskite Solar Cells with Record Certificated Power Conversion Efficiency

Ameliorating the Interfacial Mismatch of SnO2 and Perovskite Enabling High Mechanical Stability for Flexible Perovskite Solar Cells

High‐Performance Flexible Perovskite Solar Cells via Precise Control of Electron Transport Layer

Highly Efficient Flexible Perovskite Solar Cells Through Pentylammonium Acetate Modification with Certified Efficiency of 23.35%

Chemical Bath Deposition of SnO2 Films on PEN/ITO Substrates for Efficient Flexible Perovskite Solar Cells

Highly Efficient Large-Area Flexible Perovskite Solar Cells Containing Tin Oxide Vertical Nanopillars without Oxygen Vacancies

Buried Interface Optimization for Flexible Perovskite Solar Cells with High Efficiency and Mechanical Stability

Improved SnO2 Electron Transport Layers Solution‐Deposited at Near Room Temperature for Rigid or Flexible Perovskite Solar Cells with High Efficiencies

Fapbi(3) Flexible Solar Cells With A Record Efficiency Of 19.38% Fabricated In Air Via Ligand And Additive Synergetic Process

Highest‐Efficiency Flexible Perovskite Solar Module by Interface Engineering for Efficient Charge‐Transfer

Enhancing Electron Transport Via Graphene Quantum Dot/sno2 Composites for Efficient and Durable Flexible Perovskite Photovoltaics

An effective oxygen vacancy restrain method for flexible perovskite solar cells with enhanced performance and bending resistance

Recent Advances of Device Components Toward Efficient Flexible Perovskite Solar Cells

Enhanced Particle‐to‐Particle Interaction of Tin Oxide Electron Transporter Layer for Scalable Flexible Perovskite Solar Cells

Mechanically and operationally stable flexible inverted perovskite solar cells with 20.32% efficiency by a simple oligomer cross-linking method

Enhanced photovoltaic performance of SnO2 based flexible perovskite solar cells via introducing interfacial dipolar layer and defect passivation

Porous Lead Iodide Layer Promotes Organic Amine Salt Diffusion to Achieve High Performance p‐i‐n Flexible Perovskite Solar Cells

Large improvement of photovoltaic performance of flexible perovskite solar cells using a multifunctional phospho-ethanolamine-modified SnO2 layer

Room-Temperature Sputtered SnO2 as Robust Electron Transport Layer for Air-Stable and Efficient Perovskite Solar Cells on Rigid and Flexible Substrates