Abstract:Lithium-ion batteries (LIBs) have profoundly advanced the development of electric vehicles (EV). However, one of the remaining bottlenecks in the widespread adoption of EVs is the long charging time required for commercial LIBs. There is a global push towards extreme fast charging (XFC) to reduce charging times to 10-15 minutes. 1 However, XFC results in rapid degradation in the electrochemical performance of batteries, mainly due to Li plating. This plating refers to the loss of active Li, where it either becomes dead meaning electronically disconnected after plating on the anode, or it becomes inactive due to the irreversible reaction of Li with the electrolyte to form a solid electrolyte interphase. Dead Li contributes significantly to capacity loss during XFC; 3 thus, differentiating dead and inactive from active Li is extremely important to unravel their link with battery capacity fade. However, owing to the complexity of these competing electrochemical reactions in addition to the intricacy of detecting Li at the buried graphite-separator-electrolyte interface, a comprehensive understanding of Li plating remains a challenge. In this work, we conducted non-destructive, in-situ three-dimensional (3D) characterization of dead and active Li on energy-dense graphite electrodes during XFC using high-resolution neutron micro-computed tomography (μCT). Thick or industry-relevant (negative and positive electrodes ~ 130 μm) graphite electrodes are promising battery materials because they store higher amounts of energy. However, they plate Li faster and at lower XFC cycle numbers, and hence experience higher loss in battery capacity due to Li plating. To characterize Li plating on thick graphite electrodes, we performed high-resolution neutron μCT 4 (pixel size: ~ 5.74 μm; effective spatial resolution: ~10-15 μm) at the ICON beamline 5 at the Swiss Spallation Neutron Source at the Paul Scherrer Institute. Neutron μCT was used because it provides high relative neutron contrast between Li and C (~ 71.87: 5.55 barns 6 ) for in-situ 3D imaging. Therefore, to leverage high-resolution neutron μCT for in-situ Li detection, we designed a neutron-friendly LIB. Our designed battery enabled excellent neutron transmission at the graphite-separator-electrolyte interface while exhibiting similar XFC performance at a 6C charging-rate between 3.0 and 4.1V. We imaged three batteries in the charged and discharged states under the following conditions: 4 cycles at 1C charging; 4 and 6 cycles at 6C charging. Here, we note that since inactive Li was below the spatial resolution of the ICON beamline, only dead , active , and plated Li were investigated in this work. Our results reveal changes in dead Li morphologies from isolated deposits after 4 cycles at 1C charging to increasingly mossy-like dense deposits covering the entire circumference of the graphite electrode after 6 cycles at 6C charging. Furthermore, as the XFC cycle number increased from four to six at 6C charging, the amount of dead Li increased significantly. After 6 cycles at 6C charging, we also observed dead Li outgrowths in a circular geometry onto the separator around the graphite electrode. Using our imaging data, we determined a quantitative link between the amounts of dead and active Li with the capacity loss of the battery. Our analysis suggests that the amounts of plated and dead Li increase with the charging rate and cycle number. Finally, we developed quantitative relationships in 3D between the amounts of dead , active , and plated Li, and XFC-related capacity loss of the battery. In conclusion, this work contributed to the advanced understanding of the morphological evolution of dead , active , and plated Li and their relationship with XFC-related capacity loss on thick graphite electrodes. We believe these insights will help inform rational 3D designs of thick graphite electrodes that will minimize Li plating in fast-charged LIBs. References: Liu et al . (2019). Challenges and opportunities towards fast-charging battery materials. Nature Energy, 1. Paul et al . (2021). A Review of Existing and Emerging Methods for Lithium Detection and Characterization in Li‐Ion and Li‐Metal Batteries. Advanced Energy Materials , 11 (17), 2100372. Morgano et al. (2018). Unlocking high spatial resolution in neutron imaging through an add-on fibre optics taper. Optics Express , 26 (2), 1809-1816. Kaestner et al . (2011). The ICON beamline–A facility for cold neutron imaging at SINQ. Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment , 659 (1), 387-393. https://www.nist.gov/ncnr/neutron-scattering-lengths-list . Keywords: Dead lithium; Active lithium; graphite-separator-electrolyte interface; Neutron imaging; Extreme Fast Charging (XFC).

Visualizing 3D Morphologies and Spatial Heterogeneities of Li after Fast-Charging via In-situ Neutron Tomography

Visualizing the Chemistry and Structure Dynamics in Lithium-Ion Batteries by In-Situ Neutron Diffraction

In Situ Probing Multiple-Scale Structures of Energy Materials for Li-Ion Batteries

3D Morphological Evolution of Dead and Active Lithium at the Graphite-Separator-Electrolyte Interface during Fast Charging

High-Throughput Lithium Plating Quantification for Fast Charging Battery Design

High-throughput Li plating quantification for fast-charging battery design

3D Progression of Dead Li on Graphite Electrodes during Extended Fast Charging

(Invited) 3-D Visualization of Li Metal Plating and Stripping with Operando Video Microscopy

In-situ Observation of Inhomogeneous Degradation in Large Format Li-ion Cells by Neutron Diffraction

Concurrent operando neutron imaging and diffraction analysis revealing spatial lithiation phase evolution in an ultra-thick graphite electrode

Fast Li Plating Behavior Probed by X-ray Computed Tomography

Multiscale dynamics of charging and plating in graphite electrodes coupling operando microscopy and phase-field modelling

Interplay of intercalation dynamics and lithium plating in monolithic and architectured graphite anodes during fast charging

Operando detection of Li plating during fast charging of Li-ion batteries using incremental capacity analysis

3D microstructure design of lithium-ion battery electrodes assisted by X-ray nano-computed tomography and modelling

High-Throughput Combinatorial Analysis of the Spatiotemporal Dynamics of Nanoscale Lithium Metal Plating

Nondestructively Visualizing and Understanding the Mechano‐Electro‐chemical Origins of “soft Short” and “creeping” in All‐Solid‐State Batteries

A multimodal operando neutron study of the phase evolution in a graphite electrode

Direct Observation of Li‐Ion Transport in Electrodes under Nonequilibrium Conditions Using Neutron Depth Profiling

Nanoscale Imaging of Lithium Ion Distribution During In Situ Operation of Battery Electrode and Electrolyte

Lithium Transport of Fast Battery Cycles in a LiMn2O4 Cathode Imaged by Operando Eels