Abstract:CONSPECTUS: To tackle the foreseen energy crisis and serious environmental problem caused by conventional energy resources, solar cells, or photovoltaics (PV), a technology that can directly convert sunlight to electricity has been considered to be one of the most important and cost-effective clean energy techniques that benefit the environment. So far, silicon-based PVs have dominated the market due to mature fabrication techniques and their relatively good power conversion efficiency (PCE) and excellent stability. In the past decades, metal halide perovskite PVs have been a major direction of current PV research owing to their intriguing optoelectronic performance. The record PCE of perovskite PV cells has unprecedently increased from an original 3.8 to 25.5%. The typical structure of a photovoltaic perovskite is ABX(3), where A refers to a monovalent cation such as methylammonium (MA(+)), cesium (Cs+), or formamidinium (FA(+)); B refers to a divalent cation such as Pb2+ or Sn2+; and X refers to a halide anion. In general, a perovskite PV device consists of an active layer of the perovskite absorber, which is connected by a hole-transporting layer (HTL) and an electron-transporting layer (ETL). In the beginning, the strategies to improve the PCEs mainly focused on developing an effective method to grow a smooth and continuous polycrystalline film. After the improvement of the baseline PCE of the perovskite PVs, various techniques were employed to reduce the defects of perovskite formed at grain boundaries and surfaces, further pushing the PCEs of perovskite PV devices to over 20%. In the meantime, the discovery of suitable and low-cost interfacial materials such as electron-transporting materials and hole-transporting materials has appealed to the attention of the perovskite research community to accelerate the commercialization of the perovskite PVs. In this Account, we start from our efforts to develop facile and effective fabrication strategies to obtain smooth and continuous polycrystalline perovskite thin films, including vapor-assisted and moisture-assisted perovskite crystal growth. The strategies and the in-depth mechanisms of preventing the formation of specific detrimental defects accumulated at grain boundaries or the surface are also portrayed by designing various passivation molecules with certain functional groups, such as carbonyl groups, amine groups, or sulfonic groups. Some systematically designed electron- or hole-transporting materials to improve the charge extraction and collection efficiency in perovskite PV devices are discussed as well. Finally, future perspectives for further enhancing the long-term stability and PCE are proposed to accelerate the commercialization of perovskite PV devices in the next decade.

Holistic Approach to Low‐Dimensional Perovskite Enveloping of Internal Interfaces and Grain Boundaries in Perovskite Solar Cells

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Defect Passivation and Electrical Conductivity Enhancement in Perovskite Solar Cells Using Functionalized Graphene Quantum Dots

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

Constructing Ultra-Shallow Near-Edge States for Efficient and Stable Perovskite Solar Cells

Grain Boundary Chemical Anchoring via Bidirectional Active Site Additive Enables Efficient and Stable Perovskite Solar Cells

Nano-capillary induced assemble of quantum dots on perovskite grain boundaries for efficient and stable perovskite solar cells

Highly efficient and stable perovskite solar cells enabled by low-dimensional perovskitoids

Crosslinkable and Chelatable Organic Ligand Enables Interfaces and Grains Collaborative Passivation for Efficient and Stable Perovskite Solar Cells

Dual Optimization of Bulk and Interface Via the Synergistic Effect of Ligand Anchoring and Hole Transport Dopant Enables 23.28% Efficiency Inverted Perovskite Solar Cells

Chemical Sintering Reduced Grain Boundary Defects for Stable Planar Perovskite Solar Cells

Oligomeric Silica-Wrapped Perovskites Enable Synchronous Defect Passivation and Grain Stabilization for Efficient and Stable Perovskite Photovoltaics

Synchronous Modulation of Defects and Buried Interfaces for Highly Efficient Inverted Perovskite Solar Cells

Effective passivation of defects in high-performance tin oxide-based perovskite solar cells using guanidinium phosphate additives

Synergistic Full‐Scale Defect Passivation Enables High‐Efficiency and Stable Perovskite Solar Cells

Simultaneous Passivation of Bulk and Interface Defects with Gradient 2D/3D Heterojunction Engineering for Efficient and Stable Perovskite Solar Cells.

Grain Boundary Modification via F4TCNQ To Reduce Defects of Perovskite Solar Cells with Excellent Device Performance

Molecular Bridge Assisted Bifacial Defect Healing Enables Low Energy Loss for Efficient and Stable Perovskite Solar Cells

Solvation‐Driven Grain Boundary Passivation Improving the Performance of Perovskite Solar Cells

Bidirectional Targeted Therapy Enables Efficient, Stable, and Eco‐Friendly Perovskite Solar Cells

Halides‐enhanced buried interfaces for stable and extremely low‐voltage‐deficit perovskite solar cells