Abstract:The severe oxidation of metal elements leads to a large amount of oxide inclusions that hinder the formation of metallurgical bonds across intersplat interfaces during thermal spraying in an ambient atmosphere, which further degrades the performance of thermally sprayed metal coatings. Controlling the oxidation of metal elements during spray deposition remains a significant challenge. In this paper, the thermodynamic and kinetic requirements of in-situ in-flight deoxidation by adding deoxidizer elements (diamond particles) to Fe / Al spray powders to achieve oxide-free molten droplets in an ambient atmosphere were investigated. Fe / Al / 2.5C composite powders containing 2.5wt.% diamond particles were prepared by mechanical alloying. Atmospheric plasma spraying (APS) was used to generate an oxide-free molten spray of FeAl particles at temperatures higher than 2 000 degrees C. This was achieved by the in-situ self-oxide cleaning effect of in-flight particles by carbon, which prevented metal droplets from oxidizing in an open atmosphere. For comparison, a FeAl coating was also deposited using Fe / Al composite powders prepared by mechanical alloying. The particle velocity and temperature were measured by a commercial thermal-spraying particle diagnostic system. The microstructures of the coatings were characterized by scanning electron microscopy and X-ray diffraction. The chemical compositions of the coatings were measured by inductively coupled plasma spectroscopy. The adhesive strength and hardness of the plasma-sprayed FeAl-based coatings were tested. The results show that under the combined effects of plasma- jet heating and the FeAl exothermic reaction, the heated FeAl spray particles could reach a high temperature of over 2 100 degrees C, which meets the thermodynamic conditions for carbon in-situ deoxidation. Because oxidation occurs from the surface of an in-flight molten droplet, to maintain continuous deoxidation of the molten FeAl droplet, the rapid transfer of carbon from the interior of the molten droplet to the surface is necessary. It was confirmed that the strong convection flow of the molten metal droplets satisfied the kinetic conditions of carbon in-situ in-flight deoxidation. The oxygen content in the APS-sprayed FeAl coatings increased with the increase of the spray distance. In contrast, the oxygen content in the APS-sprayed FeAl / 2.5C coatings decreased from 1.01 wt.% to 0.48 wt.% as the spray distance increased from 70 mm to 150 mm. This was accompanied by the decrease in carbon content from 1.41 wt.% to 0.31 wt.%, indicating the effective protection of Fe and Al from oxidation by the carbon in the droplet. Compared with the oxygen content of 3.67 wt.% in traditional FeAl coating, the oxygen content of the FeAl / 2.5C coatings was reduced to less than 0.5 wt.%. Considering that the carbon content of the coatings decreased as the spray distance increased, the results confirm that the in-flight oxidation of Fe and Al was suppressed by the preferential sacrificial oxidation of carbon in the molten droplets. Thus, the oxide in the FeAl / 2.5C coatings was mainly attributed to post-deposition oxidation. Moreover, the FeAl droplet reached the temperature to realize the spread-fusing self-metallurgical bonding effect for FeAl splats. The coatings exhibited a dense microstructure with an apparent porosity of less than 0.5%. The adhesive bonding strength of the prepared coatings exceeded 59.2 MPa owing to metallurgical bonding. The hardness of the coatings reached 590 HV0. 3, which was approximately twice that of traditional FeAl coatings. This was attributed to the reinforcement provided by the Fe3AlCx cementite phase resulting from the residual carbon in the coating.

Citric Acid Enhances the Ignition and Combustion Performance of Aluminum: Coating and Etching

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

Enhancing the Ignition and Combustion Performance of Aluminum by Surface Modification: Tannic Acid and Tea Polyphenols

Enhancing the combustion of nAl with AlF 3 coating: gas–solid reaction mechanism for reducing combustion agglomeration of Al powder

Calcium Fluoride Promoting the Combustion of Aluminum Powder

Enhancement of the ignition and combustion performance of nano-aluminum: the effect of cryolite

Combustion and heat release characteristics of micron aluminum with extremely large specific surface area obtained by L-malic acid surface corrosion

Improved ignition and combustion performances of aluminum nanoparticles by in-situ partial conversion of native alumina to surface Al-MOF shell

Exploring the Combustion Mechanism of Single Micron-Sized Aluminum Particles with a Numerical Model

Establishing the interface layer on the aluminum surface through the self-assembly of tannic acid (TA): Improving the ignition and combustion properties of aluminum

Effect of Several Inorganic Additives on Microstructure and Properties of Microarc Oxidation Coating on Aluminium Alloy

AP and nFe2O3 synergistically improve the ignition and combustion performance of aluminum particles

AP and Nfe 2 O 3 Synergistically Improve the Ignition and Combustion Performance of Aluminum Particles

Sodium Fluoroaluminate Promoting the Combustion of Micron-Sized Aluminum Powder with Different Particle Sizes in Carbon Dioxide

Effect of stearic acid coating on the flame propagation and reaction mechanism of AlH 3

Controlling the Energy Release Behavior of Aluminum Nanoparticles As Metal Fuels by Atomic Layer Deposited Copper Oxide Nanocoatings

Mechanism of Suppressing Oxidation of FeAl Molten Droplet by Adding C to Powder and Its Effect on Microstructure and Properties of Plasma-sprayed Coating

High Performance Nal@cuo Core-Shell Particles with Improved Combustion Efficiency and the Effect of Interfacial Layers on Combustion

Metastable Intermixed Core-shell Al@M(IO3)x Nanocomposites with Improved Combustion Efficiency by Using Tannic Acid As a Functional Interfacial Layer

Synthesis, Analysis, and Characterization of Aluminum Nanoparticles Coated with 2,2,4-Trimethylpentane

Redispersion Effects of Citric Acid on CoMo/γ-Al2O3 Hydrodesulfurization Catalysts