Abstract:Purpose: Mechanical properties of dental composite resins need to be improved in order to enhance their performance for applications in direct restorations. Application of nanoparticles in this field is a recent development. The aim of this study was to investigate the mechanical properties of experimental composites containing various mass fractions of silica nanoparticles. Materials and methods: Experimental composites were composed of a visible-light-curing monomer mixture (70 wt% Bis-GMA and 30 wt% TEGDMA) and silica nanoparticles of a size ranging from 20 nm to 50 nm modified with gamma-methacryloxy propyl trimethoxy silane (gamma-MPS) as reinforcing filler. The composites were classified into four groups according to their filler mass fractions ranging from 20% to 50%. Following the same preparation procedure, a conventional composite was also fabricated consisting of a mass percentage of 60% silica fillers having particle sizes ranging from 10 microm to 40 microm in the same organic matrix, which served as control. Ten specimens were prepared of each experimental group and also of the control. Fracture toughness was measured using single-edge notched bend (SENB) specimens. Specimen fracture surfaces were mounted on aluminum stubs with carbon cement, sputter-coated with gold and examined under scanning electron microscopy (SEM). Flexural strength was evaluated through a standard three-point bending test and Vickers microhardness test was performed to investigate the hardness of the samples. Results: Filler mass fraction had a significant effect on composite properties. Fracture toughness, flexural strength, and hardness of composites at filler mass fraction of 40% of silica nanoparticles were (mean +/- SD) 1.43 +/- 0.08 MPa.m(1/2), 149.74 +/- 8.14 MPa, and 62.12 +/- 3.07 VHN, respectively; relevant values for composites at 50% mass fraction of silica nanoparticles were 1.38 +/- 0.07 MPa.m(1/2), 122.83 +/- 6.13 MPa, and 70.69 +/- 3.67 VHN, respectively, all of which were significantly higher than 1.07 +/- 0.06 MPa.m(1/2), 104.61 +/- 8.73 MPa, and 52.14 +/- 4.02 VHN of the control, respectively (Tukey's multiple comparison test; family confidence coefficient = 0.95). Measured values for composites at 20% mass fraction of silica nanoparticles were 0.94 +/- 0.06 MPa.m(1/2), 103.41 +/- 7.62 MPa, and 42.87 +/- 2.61 VHN, respectively; relevant values for composites at 30% mass fraction of silica nanoparticles were 1.16 +/- 0.07 MPa.m(1/2), 127.91 +/- 7.05 MPa, and 51.78 +/- 3.41 VHN, respectively. Conclusions: Reinforcement of dental composite resins with silica nanoparticles resulted in a significant increase in the evaluated mechanical properties in comparison with the conventional composite. The filler mass fraction played a critical role in determining the composite's mechanical properties.

Preparation, characterization, and mechanical properties of dental photosensitive resin composites: effect of amalgamation with boron nitride nanosheets

Mechanical and Antimicrobial Properties of Boron Nitride/Methacrylic Acid Quaternary Ammonium Composites Reinforced Dental Flowable Resins

Boron nitride nanosheets modified with zinc oxide nanoparticles as novel fillers of dental resin composite

Effects of Bacterial Cellulose Nanocrystals on the Mechanical Properties of Resin-Modified Glass Ionomer Cements

Enhanced Thermal and Electrical Properties of Photosensitive Resin Matrix Composites with Hexagonal Boron Nitride Nanosheets

The Mechanical and Antibacterial Properties of Boron Nitride/Silver Nanocomposite Enhanced Polymethyl Methacrylate Resin for Application in Oral Denture Bases

Effect of Silica Nanospheres Silanized by Functional Silanes on the Physicochemical and Mechanical Properties of Bis-GMA/TEGDMA Dental Composite Resin by Photocuring Synthesis

Boron nitride nanoplatelets as reinforcement material for dental ceramics

Investigation of mechanical properties of experimental Bis-GMA/TEGDMA dental composite resins containing various mass fractions of silica nanoparticles

The researchment of nami-material reinfoced dental composite resin

Effects of Hexagonal Boron Nitride and Mesoporous Silica Nanoparticles on the Morphology, Mechanical Properties and Antimicrobial Activity of Dental Composites

A Study of 3D-Printable Reinforced Composite Resin: PMMA Modified with Silver Nanoparticles Loaded Cellulose Nanocrystal.

Preparation of Bis-GMA/Nano(SiO2-ZrO2) Composite Resin Dental Material

Evaluation of the Surface Hardness and Roughness of a Resin-Modified Glass Ionomer Cement Containing Bacterial Cellulose Nanocrystals

Nanoindentation Study on Mechanical Properties and Curing Depth of Dental Resin Nanocomposites

The Effect of UDMA/TEGDMA Mixtures and Bioglass Incorporation on the Mechanical and Physical Properties of Resin and Resin‐Based Composite Materials

Physicochemical Properties of Bis-GMA/TEGDMA Dental Resin Reinforced with Silanized Multi-Walled Carbon Nanotubes

Characterization of Experimental Nanoparticulated Dental Adhesive Resins with Long-Term Antibacterial Properties

Effects of BN on the microstructural evolution and mechanical properties of BAS-BN composites

Improved performance of Bis-GMA/TEGDMA dental composites by net-like structures formed from SiO2 nanofiber fillers

Synthesis of boron nitride@copper oxide‐based light‐curing resin composites: Investigating mechanical and antibacterial properties