Abstract:CONSPECTUS: To tackle the foreseen energy crisis and serious environmental problem caused by conventional energy resources, solar cells, or photovoltaics (PV), a technology that can directly convert sunlight to electricity has been considered to be one of the most important and cost-effective clean energy techniques that benefit the environment. So far, silicon-based PVs have dominated the market due to mature fabrication techniques and their relatively good power conversion efficiency (PCE) and excellent stability. In the past decades, metal halide perovskite PVs have been a major direction of current PV research owing to their intriguing optoelectronic performance. The record PCE of perovskite PV cells has unprecedently increased from an original 3.8 to 25.5%. The typical structure of a photovoltaic perovskite is ABX(3), where A refers to a monovalent cation such as methylammonium (MA(+)), cesium (Cs+), or formamidinium (FA(+)); B refers to a divalent cation such as Pb2+ or Sn2+; and X refers to a halide anion. In general, a perovskite PV device consists of an active layer of the perovskite absorber, which is connected by a hole-transporting layer (HTL) and an electron-transporting layer (ETL). In the beginning, the strategies to improve the PCEs mainly focused on developing an effective method to grow a smooth and continuous polycrystalline film. After the improvement of the baseline PCE of the perovskite PVs, various techniques were employed to reduce the defects of perovskite formed at grain boundaries and surfaces, further pushing the PCEs of perovskite PV devices to over 20%. In the meantime, the discovery of suitable and low-cost interfacial materials such as electron-transporting materials and hole-transporting materials has appealed to the attention of the perovskite research community to accelerate the commercialization of the perovskite PVs. In this Account, we start from our efforts to develop facile and effective fabrication strategies to obtain smooth and continuous polycrystalline perovskite thin films, including vapor-assisted and moisture-assisted perovskite crystal growth. The strategies and the in-depth mechanisms of preventing the formation of specific detrimental defects accumulated at grain boundaries or the surface are also portrayed by designing various passivation molecules with certain functional groups, such as carbonyl groups, amine groups, or sulfonic groups. Some systematically designed electron- or hole-transporting materials to improve the charge extraction and collection efficiency in perovskite PV devices are discussed as well. Finally, future perspectives for further enhancing the long-term stability and PCE are proposed to accelerate the commercialization of perovskite PV devices in the next decade.

Effect of Drying Methods on Perovskite Films and Solar Cells

Processing and Preparation Method for High-Quality Opto-Electronic Perovskite Film

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

Simple and effective deposition method for solar cell perovskite films using a sheet of paper

Perovskite solar cells based on screen-printed thin films

Natural drying yields efficient perovskite solar cells

Effect of spin coat speed on structure, composition and properties of perovskite films

A Review on Dry Deposition Techniques: Pathways to Enhanced Perovskite Solar Cells

Effects of Process Parameters on the Characteristics of Mixed-Halide Perovskite Solar Cells Fabricated by One-Step and Two-Step Sequential Coating.

Effect of Solvent Residue in the Thin-Film Fabrication on Perovskite Solar Cell Performance

Drying and Coating of Perovskite Thin Films: How to Control the Thin Film Morphology in Scalable Dynamic Coating Systems

Preparation of flexible perovskite solar cells by a gas pump drying method on a plastic substrate

Perovskite solar cells by vapor deposition based and assisted methods

Electrical Heating‐Assisted Multiple Coating Method for Fabrication of High‐Performance Perovskite Fiber Solar Cells by Thickness Control

Surfactant-controlled ink drying enables high-speed deposition of perovskite films for efficient photovoltaic modules

Room‐Temperature Meniscus Coating of >20% Perovskite Solar Cells: A Film Formation Mechanism Investigation

High-Performance Electron Transport Layer via Ultrasonic Spray Deposition for Commercialized Perovskite Solar Cells

Toward Industrial-Scale Production of Perovskite Solar Cells: Screen Printing, Slot-Die Coating, and Emerging Techniques

Influence of drying temperature on morphology of MAPbI$_3$ thin films and the performance of solar cells

Collaborative Fabrication of High-Quality Perovskite Films for Efficient Solar Modules through Solvent Engineering and Vacuum Flash System

Insights into Large-Scale Fabrication Methods in Perovskite Photovoltaics