Abstract:Estimating the effectiveness of hydraulic fracturing in the context of the incrfease in the shale gas demand is of great significance for enhancing shale gas production, which aims to substantially reduce fossil energy consumption and CO2 emissions. The Zhaotong national shale gas demonstration zone has complex stress structures and well-developed fracture zones, and thus it is challenging to achieve targeted reservoir segment transformation. In this paper, we construct and optimize the geometry of hydraulic fractures at different pressures considering the upper and lower barriers in hydraulic fracturing simulation experiments and numerical modeling. The numerical simulation results show that the pore pressure exhibits a stepped pattern around the fracture and an elliptical pattern near the fracture tip. During the first time of injection, the pore pressure rapidly increases to 76 MPa, dropping sharply afterward, indicating that the fracture initiation pressure is 76 MPa. During the fracture propagation, the fracture length is much greater than the fracture height and width. The fracture width is larger in the middle than on the two sides, whereas the fracture height gradually decreases at the fracture tip in the longitudinal direction until it closes and is smaller near the wellbore than at the far end. The results revealed that the fracture width at the injection point reached the maximum value of 9.05 mm, and then it gradually decreased until the fracture width at the injection point dropped to 6.33 mm at the final simulation time. The fracture broke through the upper and lower barriers due to the dominance of the effect of the interlayer principal stress difference on the fracture propagation shape, causing the hydraulic fracture to break through the upper and lower barriers. The results of the physical simulation experiment revealed that after hydraulic fracturing, multiple primary fractures were generated on the side surface of the specimen. The primary fractures extended, inducing the generation of secondary fractures. After hydraulic fracturing, the width of the primary fractures on the surface of the specimen was 0.382–0.802 mm, with maximum fracture widths of 0.802 mm and 0.239 mm, representing a decrease of 70.19% in the maximum fracture width. This work yielded an important finding, i.e., the urgent need for hydraulic fracturing adaptation promotes the three-dimensional development of a gas shale play.

Numerical Simulation of Hydraulic Fracture Characteristics in Gas Hydrate Bearing-Sediments by Using CDEM

2D Numerical Simulation of Hydraulic Fracturing in Hydrate-Bearing Sediments Based on the Cohesive Element

Numerical Simulation of Direct Shear Tests on Gas Hydrate-Bearing Sediments Using the Discrete Element Method

Embedded Discrete Fracture Model for Investigating the Effect of Fractures on Gas Hydrate Production

Numerical analysis of the production behaviors and geomechanical responses during natural gas hydrate production by vertical wells fracturing

Enhanced gas production efficiency of class 1,2,3 hydrate reservoirs using hydraulic fracturing technique

Numerical simulation of single-cluster and multi-cluster fracturing of hydrate reservoir based on cohesive element

Numerical simulation of hydraulic fracturing-assisted depressurization development in hydrate bearing layers based on discrete fracture models

Production Simulation of Stimulated Reservoir Volume in Gas Hydrate Formation with Three-Dimensional Embedded Discrete Fracture Model

Research on Hydraulic Fracture Propagation Patterns in Multilayered Gas Hydrate Reservoirs Using a Three-Dimensional XFEM-Based Cohesive Zone Method

3D DEM Investigation on Macro-Meso Mechanical Responses of Gas Hydrate-Bearing Sediments in Process of Unloading Confining Pressure

A DEM–CFD Coupling Method

Numerical Simulation of Hydraulic Fracturing Based on Discrete Element Method

Numerical analysis of gas production from large-scale methane hydrate sediments with fractures

Numerical Simulation of Hydraulic Fractures Breaking through Barriers in Shale Gas Reservoir in Well YS108-H3 in the Zhaotong Shale Gas Demonstration Area

Simulation of Production Dynamics after Reservoir Stimulation in Hydrate Reservoirs Considering Complex Fracture Morphology

Numerical simulation of fracture propagation morphology in hydraulic fracturing development of geothermal reservoirs based on the CDEM-THM3D

An Integrated Method to Characterize Shale Gas Reservoir Performance

Evaluation of the gas production enhancement effect of hydraulic fracturing on combining depressurization with thermal stimulation from challenging ocean hydrate reservoirs

A hydrate reservoir renovation device and its application in nitrogen bubble fracturing

Preliminary experimental investigation on long-term fracture conductivity for evaluating the feasibility and efficiency of fracturing operation in offshore hydrate-bearing sediments