Abstract:This paper introduces adsorption processes with scaled sizes for post-combustion carbon capture, pre-combustion carbon capture, and direct air capture (DAC). Technical characteristics, separation performances, and operating energy consumptions of adsorption-based pilot plants for carbon capture are analyzed. Opportunities and challenges of adsorption-based carbon capture processes in future development are illustrated. Adsorption-based post-combustion carbon capture is a relatively mature technology, which can be applied to retrofitted power plants. However. in order to commercialize this technology, quantities of research and development resources are still needed. Researches on adsorption-based post-combustion carbon capture should focus on the following three aspects: (1) Low-temperature adsorbents with excellent CO2 working capacities, kinetics, and stabilities, (2) low energy consumption cycles using steam purge, and (3) contactors with low gas-solid mass transfer resistances. The warm gas clean-up technology based on pressure swing adsorption (PSA) is a research hotspot for pre-combustion carbon capture. At present, many warm gas clean-up pilot plants are being built worldwide, and in the meantime, some bottlenecks appear. First. the CO2 working capacities of elevated temperature adsoibents are still lower than those of low temperature adsorbents. The recently reported molten salt-promoted magnesium oxide achieves a very high working capacity through the bulk phase chemical absorption, but a carbon capture prototype needs to be established to verify its cyclic stability. Achieving both high purity and high recovery of warm gas clean-up consumes a large amount of high temperature steam. Although multi-train PSA configuration can reduce the energy consumption. it also increases the operating complexity and equipment investment. In addition to CO2 the removal of other impurities such as H2S, COS, HCl, and heavy metals in syngas/reforming gas should be considered. The sorption enhanced reforming with oxy-fuel regeneration process based on high temperature adsorbents can achieve CO2 enrichment in the regeneration reactor. However, pilot plants for this technology are currently lacking, and so detailed techno-economic analysis is still needed to assess its capture cost. Although DAC is a relatively new concept and is still in the early stage for large-scale commercial application, the synergy between DAC and conventional carbon capture technologies can mitigate climate change effects in the long run. The development of DAC technologies needs to pay special attention to the pressure drop problems. Novel gas-solid contactors using structural adsorbents can effectively reduce the power consumption of the fan. Steam purge under subatomospheric pressures reduces the regeneration temperature of DAC, and thus makes the utilization of renewable energy and industrial waste heat for regeneration becoming possible. When steam purge is used, the cyclic stability of the adsoibents should be concerned. For instance. polyamine impregnated adsoibents are prone to amine leakage in the presence of steam. Therefore. the development of hydrothermally stable DAC adsorbents is significantly important.

Recent Advances in Elevated-Temperature Pressure Swing Adsorption for Carbon Capture and Hydrogen Production

Recent Advances and Challenges in Ionic Materials for Post-Combustion Carbon Capture

Advances in Post‐Combustion CO 2 Capture by Physical Adsorption: From Materials Innovation to Separation Practice

Sustainable CO2 management through integrated CO2 capture and conversion

Recent Progress in the Integration of CO2 Capture and Utilization

Thermodynamic Exploration of Two-Stage Vacuum-Pressure Swing Adsorption for Carbon Dioxide Capture

Elevated Temperature Pressure Swing Adsorption Process for Reactive Separation of CO/CO2 in H2-rich Gas

Analysis on Temperature Vacuum Swing Adsorption Integrated with Heat Pump for Efficient Carbon Capture

Progress in Post-Combustion Technology for Carbon Dioxide Capture

The Advances of Post-combustion CO2 Capture with Chemical Solvents: Review and Guidelines

Recent progress in carbon dioxide capture technologies: A review

Elevated Temperature Adsorbents for Separation Applications

Large-scale Applications and Challenges of Adsorption-Based Carbon Capture Technologies

The Advances of Adsorbents in the Field of CO_2 Capture

(Invited) Elevated Temperature CO2 Adsorption Separation and Electrochemical Conversion：Reaction Mechanism and Technology Development

Porous Adsorption Materials for Carbon Dioxide Capture in Industrial Flue Gas

Advancements and Challenges in Adsorption‐Based Carbon Capture Technology: From Fundamentals to Deployment

Recent Advances in Potassium-Based Adsorbents for CO2 Capture and Separation: a Review

Recent advances in direct air capture by adsorption

The current status of high temperature electrochemistry-based CO2 transport membranes and reactors for direct CO2 capture and conversion

Adsorbents for the post-combustion capture of CO2 using rapid temperature swing or vacuum swing adsorption