Abstract:To address shortages in construction materials for island engineering, tackle the accumulation of solid waste, and inhibit the shrinkage of geopolymers, coral waste was utilized as the internal curing material to prepare high-performance marine geopolymer concrete (MGC) with seawater, sea-sand, and normal limestone aggregate (LsA). The coral coarse aggregate (CorA) used in this investigation has a total porosity ranging from 50% to 58.3% with internal pore diameters spanning 50-400 μm. The water desorption of CorA followed a two-stage pattern within a relative humidity (RH) range of 75%-85%, becoming nonlinear above 90% RH, which released about 85% of its moisture within 200 h at 97% RH, demonstrating potential for internal curing. Adding a small amount of CorA to MGC increased slump and setting time by providing internal curing water. However, as CorA content exceeded 30%, the slump significantly decreased due to reduced mixing water and elevated activator concentration, while the initial setting time slightly decreased. Furthermore, the inclusion of saturated CorA in MGC significantly reduced autogenous shrinkage, with higher CorA contents (exceeding 30%) leading to slight expansion in the early stages and nearly eliminating shrinkage at contents above 40%. The greater drying shrinkage in geopolymer systems compared to ordinary Portland cement is due to capillary pressure compressing the product framework, converting larger gel pores into smaller ones. Additionally, the layered calcium aluminosilicate hydrate (C-A-S-H) gel exhibits more pronounced creep characteristics under low internal humidity conditions. The higher CorA content in MGC promoted the formation of hybrid C, N-A-S-H gel and hydrotalcite-like phases, and reduced carbonation issues. The interfacial transition zone (ITZ) between CorA and the geopolymer matrix formed a robust mechanical interlock, enhancing tensile strength and minimizing shrinkage-induced cracks. Based on overall performance and marine material utilization, an optimal substitution rate of CorA between 40% and 50% is recommended.

Properties of Fly Ash Geopolymer Concrete As Marine Artificial Reef Building Materials

Low-carbon enhancement of fly ash geopolymer concrete: Lateral deformation, microstructure evolution and environmental impact

Experimental Study on Fabrication of Environment-Friendly Concrete by Solidifying Aeolian Sand and Natural Gravel with Fly Ash-Based Geopolymer

Resistance of Chloride and Sulfate of Geopolymer based on fly ash and silica fume as alternative raw materials.

Properties of fresh and hardened fly ash/slag based geopolymer concrete: A review

Development of Low Calcium Fly-Ash Based Geopolymer Concrete Using Marble Powder

The microstructure and durability of fly ash-based geopolymer concrete: A review

Potential of fly ash geopolymer concrete as repairing and retrofitting solutions for marine infrastructure: A review

Geopolymer Composites for Marine Application: Structural Properties and Durability

A Comprehensive Review on Fly Ash-Based Geopolymer

Efficient utilization of coral waste for internal curing material to prepare eco-friendly marine geopolymer concrete

On the use of blast furnace slag and steel slag in the preparation of green artificial reef concrete

Evaluation of Properties of Concrete Without Cement Produced Using Fly Ash‐Based Geopolymer

Cleaner geopolymer prepared by co-activation of gasification coal fly ash and steel slag: durability properties and economic assessment

Utilization of Calcium Carbide Residue as Solid Alkali for Preparing Fly Ash-Based Geopolymers: Dependence of Compressive Strength and Microstructure on Calcium Carbide Residue, Water Content and Curing Temperature

Sea/coral sand in marine engineered geopolymer composites: Engineering, mechanical, and microstructure properties

Sulfate Resistance of Class C/class F Fly Ash Geopolymers

Experiment on Compressive Properties and Microscopic Analysis of Sea Sand Geopolymer-Based Recycled Concrete

Life Cycle Assessment and Impact Correlation Analysis of Fly Ash Geopolymer Concrete

Fresh and Hardened Properties of One-Part Fly Ash-Based Geopolymer Binders Cured at Room Temperature: Effect of Slag and Alkali Activators

Mechanical properties of fly ash based geopolymer concrete using only steel slag as aggregate