A Short, Novel, and Cheaper Procedure for Oligonucleotide Synthesis Using Automated Solid Phase Synthesizer

Quanlai Song,Zhiwei Wang,Yogesh S. Sanghvi

DOI: https://doi.org/10.1002/chin.200402219

2003-01-01

ChemInform

Abstract:For Abstract see ChemInform Abstract in Full Text.

What problem does this paper attempt to address?

A Simple and Efficient Microfluidic System for Reverse Chemical Synthesis (5′-3′) of a Short-Chain Oligonucleotide Without Inert Atmosphere

P. Tue,R. Bhardwaj,M. Biyani,Y. Takamura

DOI: https://doi.org/10.3390/APP9071357

2019-03-31

Applied Sciences

Abstract:Reverse DNA synthesis (5′-3′) plays diverse functional roles in cellular biology, biotechnology, and nanotechnology. However, current microfluidic systems for synthesizing single-stranded DNAs at a laboratory scale are limited. In this work, we develop a simple and efficient polydimethylsiloxane- (PDMS-) based microfluidic system for the reverse chemical synthesis of short-chain oligonucleotides (in the 5′-3′ direction) under ambient conditions. The use of a microfluidics device and anhydrous conditions effectively surpass the problem of moisture sensitivity during oligonucleotide synthesis. With optimized microfluidic synthesis conditions, the system is able to synthesize up to 21 bases-long oligonucleotides in air atmosphere. The as-synthesized oligonucleotides, without further purification, are characterized using matrix-assisted laser desorption ionization–time of flight (MALDI-TOF/TOF) mass spectroscopy (MS) supported by the denatured polyacrylamide gel electrophoresis (PAGE) analysis. This developed system is highly promising for producing the desired sequence at the nanomolar scale on-chip and on-demand in the near future.

Materials Science,Engineering,Chemistry
De Novo Synthesis of Error-Free Long Oligos

Shiyue Fang,Reed Arneson,Yipeng Yin,Yinan Yuan

DOI: https://doi.org/10.1002/cpz1.70028

Abstract:This protocol describes the synthesis of long oligonucleotides (up to 401-mer), their isolation from complex mixtures using the catching-by-polymerization (CBP) method, and the selection of error-free sequence via cloning followed by Sanger sequencing. Oligo synthesis is achieved under standard automated solid-phase synthesis conditions with only minor yet critical adjustments using readily available reagents. The CBP method involves tagging the full-length sequence with a polymerizable tagging phosphoramidite (PTP), co-polymerizing the sequence into a polymer, washing away failure sequences, and cleaving the full-length sequence from the polymer. Cloning and sequencing guided selection of error-free sequence overcome the problems of substitution, deletion, and addition errors that cannot be addressed using any other methods, including CBP. Long oligos are needed in many areas such as protein engineering and synthetic biology. The methods described here are particularly important for projects requiring long oligos containing long repeats or stable higher-order structures, which are difficult or impossible to produce using any other existing technologies. © 2024 Wiley Periodicals LLC. Basic Protocol 1: Long oligo synthesis Support Protocol 1: Synthesis of polymerizable tagging phosphoramidite (PTP) Support Protocol 2: Synthesis of 5'-O-Bz phosphoramidite Basic Protocol 2: Catching-by-polymerization (CBP) purification Basic Protocol 3: Error-free sequence selection via cloning and sequencing.
An oligonucleotide synthesizer based on a microreactor chip and an inkjet printer

Hui Li,Ye Huang,Zewen Wei,Wei Wang,Zhenjun Yang,Zicai Liang,Zhihong Li

DOI: https://doi.org/10.1038/s41598-019-41519-0

IF: 4.6

2019-03-25

Scientific Reports

Abstract:AbstractSynthetic oligonucleotides (oligos) are important tools in the fields of molecular biology and genetic engineering. For applications requiring a large number of oligos with high concentration, it is critical to perform high throughput oligo synthesis and achieve high yield of each oligo. This study reports a microreactor chip for oligo synthesis. By incorporating silica beads in the microreactors, the surface area of the solid substrate for oligo synthesis increases significantly in each microreactor. These beads are fixed in the microreactors to withstand the flushing step in oligo synthesis. Compared to conventional synthesis methods, this design is able to avoid protocols to hold the beads and integrate more microreactors on a chip. An inkjet printer is utilized to deliver chemical reagents in the microreactors. To evaluate the feasibility of oligo synthesis using this proof-of-concept synthesizer, an oligo with six nucleotide units is successfully synthesized.

multidisciplinary sciences
Simplified gene synthesis: A one-step approach to PCR-based gene construction

Gang Wu,Julie B. Wolf,Ameer F. Ibrahim,Stephanie Vadasz,Muditha Gunasinghe,Stephen J. Freeland

DOI: https://doi.org/10.1016/j.jbiotec.2006.01.015

IF: 3.595

2006-07-01

Journal of Biotechnology

Abstract:PCR-based gene synthesis conventionally requires two steps: first, all overlapping oligonucleotides are assembled by self-priming; then an additional pair of primers is used to amplify the full-length gene product. Here we propose a simplified method of gene synthesis which combines these two steps into one. We have found that the efficiency of this one-step method, which we term "Simplified Gene Synthesis", is affected by multiple parameters of the PCR reactions. In particular, the choice of polymerase is critical for successful one-step assembly. Other important factors include the concentration of assembly oligonucleotides and amplification primers. Moreover, we offer a general method to estimate, given a known mutation rate, how many clones should be sequenced in order to be confident of obtaining at least one correct gene product. Having determined the accuracy of gene products synthesized under optimal conditions with Simplified Gene Synthesis, we show that our estimation works well. Overall, the simplified gene synthesis provides an easier and more efficient approach to gene synthesis, providing a further step towards the future goal of generalized automation for this process.

biotechnology & applied microbiology
High-fidelity De Novo Synthesis of Pathways Using Microchip-Synthesized Oligonucleotides and General Molecular Biology Equipment.

Wen Wan,Min Lu,Dongmei Wang,Xiaolian Gao,Jiong Hong

DOI: https://doi.org/10.1038/s41598-017-06428-0

IF: 4.6

2017-01-01

Scientific Reports

Abstract:Engineering and evaluation of synthetic routes for generating valuable compounds require accurate and cost-effective de novo synthesis of genetic pathways. Here, we present an economical and streamlined de novo DNA synthesis approach for engineering a synthetic pathway with microchip-synthesized oligonucleotides (oligo). The process integrates entire oligo pool amplification, error-removal, and assembly of long DNA molecules. We utilized this method to construct a functional lycopene biosynthetic pathway (11.9 kb encoding 10 genes) in Escherichia coli using a highly error-prone microchip-synthesized oligo pool ( 479 oligos) without pre-purification, and the error-frequency was reduced from 14.25/kb to 0.53/kb. This low-equipment-dependent and cost-effective method can be widely applied for rapid synthesis of biosynthetic pathways in general molecular biology laboratories.
Scalable One-Pot - Liquid-Phase Oligonucleotide Synthesis for Model Network Hydrogels.

A. Walther,Katja Schumann,Cecilia Oluwadunsin Akintayo,Guido Creusen

DOI: https://doi.org/10.26434/chemrxiv.12327569.v1

IF: 15

2020-05-20

Journal of the American Chemical Society

Abstract:Solid-phase oligonucleotide synthesis (SPOS) based on phosphoramidite chemistry is currently the most widespread technique for DNA and RNA synthesis, but suffers from scalability limitations and high reagent consumption. Liquid-phase oligonucleotide synthesis (LPOS) uses soluble polymer supports and has the potential of being scalable. However, at present, LPOS requires 3 separate reaction steps and 4-5 precipitation steps per nucleotide addition. Moreover, long acid exposure times during the deprotection step degrade sequences with high A-content (adenine) due to depurination and chain cleavage. In this work, we present the first one-pot liquid-phase DNA synthesis technique, which allows the addition of one nucleotide in a one-pot reaction of sequential coupling, oxidation and deprotection, followed by a single precipitation step. Furthermore, we demonstrate how to suppress depurination during the addition of adenine nucleotides. We showcase the potential of this technique to prepare high-purity 4-arm PEG T20 (T = thymine) and 4-arm PEG-A20 building blocks in multi-gram scale. Such complementary 4-arm PEG-DNA building blocks reversibly self-assemble into supramolecular model network hydrogels, and facilitate the elucidation of bond lifetimes. These model network hydrogels exhibit new levels of mechanical properties (storage modulus, bond lifetimes) in DNA bonds at room temperature (melting at 44 ‎°C), and thus open up pathways to next-generation DNA-materials programmable through sequence recognition and available for macroscale applications.

Medicine,Materials Science,Chemistry
A Novel and Efficient Ionic Liquid Supported Synthesis of Oligosaccharides.

JY Huang,M Lei,YG Wang

DOI: https://doi.org/10.1016/j.tetlet.2006.03.002

IF: 2.032

2006-01-01

Tetrahedron Letters

Abstract:A novel and efficient ionic liquid supported synthesis of oligosaccliarides with a general protocol of coupling and purification is described. The method represents an attractive alternative to the classical solid- and fluorous-phase synthesis strategies and combines the advantage of performing homogeneous chemistry on a relatively large scale while avoiding large excesses of reagents. (c) 2006 Elsevier Ltd. All rights reserved.
Solution phase synthesis of short oligoribonucleotides on a precipitative tetrapodal support

Alejandro Gimenez Molina,Amit M Jabgunde,Pasi Virta,Harri Lönnberg

DOI: https://doi.org/10.3762/bjoc.10.237

2014-09-29

Beilstein Journal of Organic Chemistry

Abstract:An effective method for the synthesis of short oligoribonucleotides in solution has been elaborated. Novel 2'- O -(2-cyanoethyl)-5'- O -(1-methoxy-1-methylethyl) protected ribonucleoside 3'-phosphoramidites have been prepared and their usefulness as building blocks in RNA synthesis on a soluble support has been demonstrated. As a proof of concept, a pentameric oligoribonucleotide, 3'-UUGCA-5', has been prepared on a precipitative tetrapodal tetrakis(4-azidomethylphenyl)pentaerythritol support. The 3'-terminal nucleoside was coupled to the support as a 3'- O -(4-pentynoyl) derivative by Cu(I) promoted 1,3-dipolar cycloaddition. Couplings were carried out with 1.5 equiv of the building block. In each coupling cycle, the small molecular reagents and byproducts were removed by two quantitative precipitations from MeOH, one after oxidation and the second after the 5'-deprotection. After completion of the chain assembly, treatment with triethylamine, ammonia and TBAF released the pentamer in high yields.

chemistry, organic
Development of Kilogram-Scale Convergent Liquid-Phase Synthesis of Oligonucleotides.

Xuan Zhou,William F. Kiesman,Wuming Yan,Hong Jiang,Firoz D. Antia,Jing Yang,Yannick A. Fillon,Li Xiao,Xianglin Shi

DOI: https://doi.org/10.1021/acs.joc.1c01756

2021-01-01

The Journal of Organic Chemistry

Abstract:Oligonucleotide drugs show promise to treat diseases afflicting millions of people. To address the need to manufacture large quantities of oligonucleotide therapeutics, the novel convergent liquid-phase synthesis has been developed for an 18-mer oligonucleotide drug candidate. Fragments containing tetra- and pentamers were synthesized and assembled into the 18-mer without column chromatography, which had a similar impurity profile to material made by standard solid-phase oligonucleotide synthesis. Two of the fragments have been synthesized at ∼3 kg/batch sizes and four additional tetra- and pentamer fragments were synthesized at >300-g scale, and a 34-mer was assembled from the fragments. Critical impurities are controlled in the fragment syntheses to provide oligonucleotides of purities suitable for clinical use after applying standard full-length product purification process. Impurity control in the assembly steps demonstrated the potential to eliminate chromatography of full-length oligonucleotides, which should enhance scalability and reduce the environmental impact of the process. The convergent assembly and telescoping of reactions made the long synthesis (>60 reactions) practical by reducing production time, material loss, and chances for impurity generation.
An Improved P(V) Oligonucleotide Synthesis Platform

Phil S. Baran,Molhm Nassir,Luca Gherardi,Richard L. Redman,Yonghao Jin,Feng Yao,Yang Yang,Nicholas Raheja,Arjun Natarajan,David Butler,Kyle W. Knouse

DOI: https://doi.org/10.26434/chemrxiv-2024-vj0vk

2024-10-04

Abstract:Three critical advances in simplifying the adoption of P(V)-based stereopure, phosphorothioate-containing oligonu-cleotide synthesis are reported. A more inexpensive phosphorus-sulfur incorporation reagent (Ψ-Br) is introduced, a robust linker system was developed, and a systematic study of common nucleobase protecting groups performed to significantly reduce the barrier to adoption of this technology.

Chemistry
Automatic In Situ Synthesis System for Polypeptide Biochip Based on Microfluidic Mixer

Huanhuan Shi,Kaixuan Nie,Bo Dong,Mengqiu Long,Zhengchun Liu

DOI: https://doi.org/10.1109/TNB.2020.3028313

Abstract:Biochips have become a sophisticated analytical device in the fields of biochemical sensing and genetic analysis. However, the cumbersome preparation process and the high production cost limit the versatility of its application. Herein, we have developed an automated synthesis system for in situ preparation of biochip with peptide backbone based on the microfluidic mixer and micro reaction chamber. The microfluidic mixer was used as a key component to perform the real-time activation of the carboxylic groups, leading to an instant coupling reaction of monomers with high efficiency. The repeating synthesis procedure was realized without too much manual intervention with the help of flow control system based on programmable logical controller and LabVIEW. The real-time monitoring of synthesis process was realized using a low-cost solar cell coupled with simple ultraviolet absorption device. The photodeprotection experiment revealed that an exposure time of 4 min with 20 mW/cm2 ultraviolet (UV) light at 365nm was sufficient for the complete removal of 2-(2-nitrophenyl) propyloxycarbonyl (NPPOC) groups from the synthetic sites in N, N-dimethylformamide (DMF). The practical capability performance of this synthesis system was further demonstrated by the synthesis of four cycles of aminocaproic acid, and the stepwise yield of coupling was measured to be about 96%, which was comparable with the result from literature, and indicated that this system may provide a new alternative for low-cost in situ synthesis of biochip.
A Practical Dinucleotide Phosphoramidite Chemistry for De Novo DNA Synthesis Via Block Coupling

Anzhe Shi,Liyan Liu,Fei Wang,Xinxiu Deng,Xiaoyang He,Shengqi Wang

DOI: https://doi.org/10.1016/j.tetlet.2024.155106

IF: 2.032

2024-01-01

Tetrahedron Letters

Abstract:With the development of synthetic biology, the demand for high-quality long oligonucleotides is increasing. The use of dinucleotide phosphoramidites (dimer amidites) will reduce half of the steps required in the stepwise monomer condensation, which is expected to lead to the high-quality synthesis of oligonucleotides. Herein, we report a convenient, unified procedure for the sustainable preparation of fully protected dimer amidites bearing a methyl phosphate and a β-cyanoethyl phosphoramidite. Key precursors of those amidites—dimers containing a 3′-hydroxyl group—have been prepared in high yield using a one-pot, scalable approach. The structures of all 16 dimer amidites and corresponding 3ʹ-hydroxyl dimers were confirmed by HPLC-MS and 31P NMR spectra. With these dimer amidites, modification of the standard method for automated solid-phase oligonucleotide synthesis enables high-yield block couplings. Oligonucleotides synthesized following this method are of sufficient quality to assemble gene-length DNA fragments. As a consequence, we develop a practical dinucleotide phosphoramidite chemistry for de novo DNA synthesis.
A simple method for the solid phase synthesis of oligodeoxynucleotides containing O4-alkylthymine

Y Z Xu,P F Swann

DOI: https://doi.org/10.1093/nar/18.14.4061

1990-07-25

Abstract:A route to prepare the cyanoethyl-phosphoramidite monomer of O4-alkylthymine and a method for the routine solid-phase synthesis of oligodeoxynucleotides containing O4-alkylthymine are described. This method has been used to make DNA sequences up to 48 bases in length. The amino function of the adenine and guanine in the sequence were protected with the phenoxyacetyl group, and that of cytosine with the isobutyryl group. The phosphodiesters were protected with the cyanoethyl group. This allowed complete deprotection of the oligomer with alkoxide ions (methanol/1,8- diazabicyclo[5.4.0]undec-7-ene (DBU) for the oligomers containing O4-methylthymine, or ethanol/DBU for those containing O4-ethylthymine) thus avoiding the use of ammonia which is known to attack the O4-alkylthymine to form 5-methylcytosine. There was no detectable loss of the alkyl group to form thymine.
Controlled enzymatic synthesis of oligonucleotides

Maëva Pichon,Marcel Hollenstein

DOI: https://doi.org/10.1038/s42004-024-01216-0

IF: 7.211

2024-06-19

Communications Chemistry

Abstract:Oligonucleotides are advancing as essential materials for the development of new therapeutics, artificial genes, or in storage of information applications. Hitherto, our capacity to write (i.e., synthesize) oligonucleotides is not as efficient as that to read (i.e., sequencing) DNA/RNA. Alternative, biocatalytic methods for the de novo synthesis of natural or modified oligonucleotides are in dire need to circumvent the limitations of traditional synthetic approaches. This Perspective article summarizes recent progress made in controlled enzymatic synthesis, where temporary blocked nucleotides are incorporated into immobilized primers by polymerases. While robust protocols have been established for DNA, RNA or XNA synthesis is more challenging. Nevertheless, using a suitable combination of protected nucleotides and polymerase has shown promises to produce RNA oligonucleotides even though the production of long DNA/RNA/XNA sequences (>1000 nt) remains challenging. We surmise that merging ligase- and polymerase-based synthesis would help to circumvent the current shortcomings of controlled enzymatic synthesis.

chemistry, multidisciplinary
Template-independent enzymatic synthesis of RNA oligonucleotides

Daniel J. Wiegand,Jonathan Rittichier,Ella Meyer,Howon Lee,Nicholas J. Conway,Daniel Ahlstedt,Zeynep Yurtsever,Dominic Rainone,Erkin Kuru,George M. Church

DOI: https://doi.org/10.1038/s41587-024-02244-w

IF: 46.9

2024-07-13

Nature Biotechnology

Abstract:RNA oligonucleotides have emerged as a powerful therapeutic modality to treat disease, yet current manufacturing methods may not be able to deliver on anticipated future demand. Here, we report the development and optimization of an aqueous-based, template-independent enzymatic RNA oligonucleotide synthesis platform as an alternative to traditional chemical methods. The enzymatic synthesis of RNA oligonucleotides is made possible by controlled incorporation of reversible terminator nucleotides with a common 3′- O -allyl ether blocking group using new CID1 poly(U) polymerase mutant variants. We achieved an average coupling efficiency of 95% and demonstrated ten full cycles of liquid phase synthesis to produce natural and therapeutically relevant modified sequences. We then qualitatively assessed the platform on a solid phase, performing enzymatic synthesis of several N + 5 oligonucleotides on a controlled-pore glass support. Adoption of an aqueous-based process will offer key advantages including the reduction of solvent use and sustainable therapeutic oligonucleotide manufacturing.

biotechnology & applied microbiology
Novel Polypeptide Automated Synthesis Devices: A Review

Zhu Chen,Zepeng Zhou,Meimei Zeng,Yiliang Bao,Yan Deng,Song Li,Xiaofang Luo,Nongyue He

DOI: https://doi.org/10.1166/jbn.2024.3862

2024-03-17

Journal of Biomedical Nanotechnology

Abstract:Peptides are a unique class of proteins and one-dimensional biological nanomaterials that play an exceptionally important role in life science and industrial applications. At present, peptide synthesis equipment encounters issues like low synthetic efficiency, challenges in scaling up, and limited automation. This article provides an overview of the key technologies in peptide synthesis equipment, covering aspects such as peptide information screening, peptide synthesis, and detection. It analyzes and summarizes the principles, methods, and critical challenges of traditional solid-phase peptide synthesis technology, microwave-assisted solid-phase peptide synthesis technology, and continuous-flow solid-phase peptide synthesis technology. It also discusses microfluidic solid-phase peptide synthesis technology and future research trends, offering insights into the search for an efficient, high-yield, high-purity, scalable, and intelligent peptide synthesis method, which holds significant research significance.

materials science, biomaterials,nanoscience & nanotechnology
Solid-Phase Synthesis of Phosphorothioate Oligonucleotides Using Sulfurization Byproducts for in Situ Capping.

Jimin Yang,Jessica A Stolee,Hong Jiang,Li Xiao,William F Kiesman,Firoz D Antia,Yannick A Fillon,Austen Ng,Xianglin Shi

DOI: https://doi.org/10.1021/acs.joc.8b01553

2018-01-01

Abstract:Oligonucleotides containing phosphorothioate (PS) linkages have recently demonstrated significant clinical utility. PS oligonucleotides are manufactured via a solid-phase chain elongation process in which a four-reaction cycle consisting of detritylation, coupling, sulfurization, and failure sequence capping with Ac2O is repeated. In the capping step, uncoupled sequences are acetylated at the 5'-OH to stop the chain growth and control the levels of deletion, or ( n-1), impurities. Herein, we report that the byproducts of commonly used sulfurization reagents react with the 5'-OH and cap the failure sequences. The standard Ac2O capping step can therefore be eliminated, and this 3-reaction cycle process affords a higher yield and higher or comparable overall purity compared to the conventional 4-reaction synthesis. This improvement results in reducing the number of reactions from ∼80 to ∼60 for the synthesis of a typical length 20-mer oligonucleotide. For every kilogram of an oligonucleotide intermediate synthesized, > 500 L of reagents and organic solvents is saved, and the E-factor is decreased to <1500 from ∼2000.
Solid-phase synthesis of stereoregulated oligodeoxyribonucleoside phosphorothioates

Natsuhisa Oka,Mika Yamamoto,Terutoshi Sato,Takeshi Wada

DOI: https://doi.org/10.1093/nass/nrl061

Abstract:An efficient stereocontrolled synthesis of oligodeoxyribonucleoside phosphorothioates on a solid-support by an oxazaphospholidine method was achieved. A detailed investigation on the reagents and conditions for the solid-phase synthesis revealed that the use of the capping and sulfurizing reagents which are regularly used for the conventional synthesis of phosphorothioate DNA resulted in a sluggish removal of the chiral auxiliaries on the phosphorothioate internucleotidic linkages. After optimization of the capping and sulfurizing steps, the deprotection of the internucleotidic linkages were successfully conducted under the regular basic conditions, and P-stereoregulated phosphorothioate DNA oligomers were successfully obtained with excellent diastereopurity.
For Catching-by-Polymerization Oligo Purification: Scalable Synthesis of the Precursors to the Polymerizable Tagging Phosphoramidites

Shiyue Fang,Yipeng Yin,Komal Chillar,Alexander Apostle,Bhaskar Halami,Adikari M. D. N. Eriyagama,Marina Tanasova

DOI: https://doi.org/10.26434/chemrxiv-2024-jcn9d

2024-02-23

Abstract:The catching-by-polymerization (CBP) oligodeoxynucleotide (oligo or ODN) purification method has been demonstrated suitable for large-scale, parallel, and long oligo purification. The authenticity of the oligos has been verified via DNA sequencing. Gene construction and expression have been demonstrated. A remaining obstacle to the practical utility of the CBP method is affordable polymerizable tagging phosphoramidites (PTPs) that are needed for the method. In this article, we report scalable synthesis of the four nucleoside (dA, dC, dG and dT) precursors to the PTPs using a route having six steps from inexpensive starting materials. The overall yields ranged from 21% to 35%. The scales of the synthesis presented here are up to 2.1 grams of the precursors. Because the syntheses are chromatography-free, they are predicted to be readily scalable. With the precursors, the PTPs can be synthesized in one step using standard methods involving a chromatography purification.

Chemistry
Automating the Purification and Isolation of Synthetic DNA

SS JONES,JE BROWN,DA VANSTONE,DK STONE,EL BROWN

DOI: https://doi.org/10.1038/nbt0187-67

IF: 46.9

1987-01-01

Nature Biotechnology

Abstract:We describe the application of robotics to the purification and isolation of synthetic oligodeoxyribonucleotides. Starting with commercially available components, we have designed and programmed a robot based system that can isolate oligonucleotides from polyacrylamide gel slices, prepare oligonucleotides for purification by polyacrylamide gel electrophoresis and execute a rapid purification protocol on a disposable C–18 reverse phase column. Each operation has been fully automated, including evaporative centrifugation, such that the system can execute any two procedures simultaneously with a throughput of 12 samples in about six hours.

A Short, Novel, and Cheaper Procedure for Oligonucleotide Synthesis Using Automated Solid Phase Synthesizer

A Simple and Efficient Microfluidic System for Reverse Chemical Synthesis (5′-3′) of a Short-Chain Oligonucleotide Without Inert Atmosphere

De Novo Synthesis of Error-Free Long Oligos

An oligonucleotide synthesizer based on a microreactor chip and an inkjet printer

Simplified gene synthesis: A one-step approach to PCR-based gene construction

High-fidelity De Novo Synthesis of Pathways Using Microchip-Synthesized Oligonucleotides and General Molecular Biology Equipment.

Scalable One-Pot - Liquid-Phase Oligonucleotide Synthesis for Model Network Hydrogels.

A Novel and Efficient Ionic Liquid Supported Synthesis of Oligosaccharides.

Solution phase synthesis of short oligoribonucleotides on a precipitative tetrapodal support

Development of Kilogram-Scale Convergent Liquid-Phase Synthesis of Oligonucleotides.

An Improved P(V) Oligonucleotide Synthesis Platform

Automatic In Situ Synthesis System for Polypeptide Biochip Based on Microfluidic Mixer

A Practical Dinucleotide Phosphoramidite Chemistry for De Novo DNA Synthesis Via Block Coupling

A simple method for the solid phase synthesis of oligodeoxynucleotides containing O4-alkylthymine

Controlled enzymatic synthesis of oligonucleotides

Template-independent enzymatic synthesis of RNA oligonucleotides

Novel Polypeptide Automated Synthesis Devices: A Review

Solid-Phase Synthesis of Phosphorothioate Oligonucleotides Using Sulfurization Byproducts for in Situ Capping.

Solid-phase synthesis of stereoregulated oligodeoxyribonucleoside phosphorothioates

For Catching-by-Polymerization Oligo Purification: Scalable Synthesis of the Precursors to the Polymerizable Tagging Phosphoramidites

Automating the Purification and Isolation of Synthetic DNA