Abstract:As a step towards developing a finite element model of the knee that can be used to study how the variables associated with a meniscal replacement affect tibio-femoral contact, the goals of this study were 1) to develop a geometrically accurate three-dimensional solid model of the knee joint with special attention given to the menisci and articular cartilage, 2) to determine to what extent bony deformations affect contact behavior, and 3) to determine whether constraining rotations other than flexion/extension affects the contact behavior of the joint during compressive loading. The model included both the cortical and trabecular bone of the femur and tibia, articular cartilage of the femoral condyles and tibial plateau, both the medial and lateral menisci with their horn attachments, the transverse ligament, the anterior cruciate ligament, and the medial collateral ligament. The solid models for the menisci and articular cartilage were created from surface scans provided by a noncontacting, laser-based, three-dimensional coordinate digitizing system with an root mean squared error (RMSE) of less than 8 microns. Solid models of both the tibia and femur were created from CT images, except for the most proximal surface of the tibia and most distal surface of the femur which were created with the three-dimensional coordinate digitizing system. The constitutive relation of the menisci treated the tissue as transversely isotropic and linearly elastic. Under the application of an 800 N compressive load at 0 degrees of flexion, six contact variables in each compartment (ie., medial and lateral) were computed including maximum pressure, mean pressure, contact area, total contact force, and coordinates of the center of pressure. Convergence of the finite element solution was studied using three mesh sizes ranging from an average element size of 5 mm by 5 mm to 1 mm by 1 mm. The solution was considered converged for an average element size of 2 mm by 2 mm. Using this mesh size, finite element solutions for rigid versus deformable bones indicated that none of the contact variables changed by more than 2% when the femur and tibia were treated as rigid. However, differences in contact variables as large as 19% occurred when rotations other than flexion/extension were constrained. The largest difference was in the maximum pressure. Among the principal conclusions of the study are that accurate finite element solutions of tibio-femoral contact behavior can be obtained by treating the bones as rigid. However, unrealistic constraints on rotations other than flexion/extension can result in relatively large errors in contact variables.

Finite Element Analysis of Contact Pressure Distribution for Domestic Artificial Knee Joint under Different Movements

Finite Element Analysis of Contact Pressure Distribution for Varus Artificial Knee Joint in Daily Motion

Motion Capture Based Dynamic Assessment of Hip Joint Cartilage Contact Pressure During Daily Activities.

3-D Finite Element Method Modeling and Contact Pressure Analysis of the Total Knee Joint in Flexion

Dynamic Assessment of Contact Pressure Changes in the Hip Joint Cartilage During Daily Activities.

Three-dimensional Finite Element Simulation of Total Knee Joint in Gait Cycle

FINITE ELEMENT CONTACT ANALYSIS OF A HUMAN SAGITTAL KNEE JOINT

Contact Biomechanical Responce of Bionic Joint for Biped Robot

Investigation into the Analysis Method for Assessing Contact Stress in Joint Prosthesis

Finite element analysis of in vivo tibio-femoral contact features with menisci

A Finite Element 3d Model Of In Vivo Human Knee Joint Based On Mri For The Tibiofemoral Joint Contact Analysis

Mechanical Analysis of Knee Dynamic Finite Element Model

Finite Element Analysis of Fixed-Bearing Knee Prosthesis with Different Size of Femur and Tibia Parts

Biomechanical Analysis of the Human Knee Joint

[Construction and simulation mechanical analysis of dynamic knee joint finite element model based on CT image].

[Establishment of 3-Dimensional Finite Element Model of Human Knee Joint and Its Biomechanics].

A Quasi-Dynamic Nonlinear Finite Element Model to Investigate Prosthetic Interface Stresses During Walking for Trans-Tibial Amputees

Pressure Change Of Fixed Rotational Deformities In The Femur In Human Cadaver Knees-A Biomechanical Study

Determination of Quadriceps Forces in Squat and Its Application in Contact Pressure Analysis of Knee Joint

Effect of Gait Changes on Tibio-Femoral Joint Contact Biomechanics

A finite element model of the human knee joint for the study of tibio-femoral contact