Abstract:A polymer actuator typically responds to only one or two types of stimuli, where sensing and actuation are simultaneously exerted by the same responsive polymer. In cells, sensing and actuation are exerted separately by different biomolecules, which are integrated into nanoscale assemblies to construct the signaling network, making cells a multistimuli responsive and multimodal system. Inspired by the structure–function relationship of the signaling network in cells, we have developed a strategy to select and assemble proper functional polymers into assemblies, where sensing and actuation are exerted by different polymers, and the assemblies can present novel functions beyond that of each polymer component. Three polymers [polyaniline, PANi; poly(N-isopropylacrylamide), PNIPAm; and polydimethylsiloxane, PDMS] are integrated as nodes into a simple energy transduction network, which can be regulated by three molecular factors (pH, kosmotropic anions, and polyethylene glycol). PANi converts the light or electric stimulus into heat, which triggers the actuation of PNIPAm and PDMS. Relying on this energy transduction network, the polymer assembly can respond to six types of stimuli (light, electricity, temperature, water, ions, and organic solvents) and perform different actuation modes, serving as a powerful actuator. Programmable complex deformation upon multiple simultaneous or sequential stimuli has also been achieved by this actuator. An adaptive gripper to catch thin objects and a self-regulating switch to maintain environmental humidity illustrate the wide potential of this actuator for next-generation smart materials and soft robots.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.2c01549.Photoresponsive behavior of the actuator; mechanical characterization; water-, temperature-, Na2CO3 concentration-, and organic solvent-induced actuation and deformation; programmable deformation driven by sequential stimuli; self-regulated switch to maintain the environmental humidity in a homeostatic range; adaptive grippers; finite element method simulation; optimization of the composition of PANi–PNIPAm; XRD pattern of dried PANi–PNIPAm; photothermal response of PANi aqueous suspension; bending angles of the free neutralized actuator (shown in Figure 2c) upon irradiation; FEA simulation of a fully swelled neutralized actuator under light irradiation; photo and illustrations of fingers moving up and back controlled by a red laser pointer with neutralized actuators acting as knuckles; photothermal performance of the neutralized actuator and the acidified actuator; FEA simulation of the self-curling of an actuator around a hot metal rod; internal stress- and water-induced bending of an actuator exposed to varied humidity; bilayer actuator was saturated in hexane and the swollen PDMS layer caused the actuator to fold into a roll; DSC curves of PANi–PNIPAm swollen in solution with different Na2CO3 concentrations; actuators performing multishape transformation with different length to width ratios and different initial shapes; 2D patterns with saturated Na2CO3 solution inducing the 3D shape of the actuator; and FEA simulation of inverse coiling behavior of an actuator helix upon the change of temperature and CO32– concentration (PDF)Bending and curling of an actuator driven by light (MP4)Artificial sunflower turning toward the direction of the light source (MP4)Light-induced motion of a robot hand and actuators were used as knuckles (MP4)Self-curling of an actuator around a hot steel rod (70 °C) (MP4)Water driving a box with actuators as hinges to close (MP4)Programmable deformation of an actuator in response to sequential stimuli, including light, humidity, heat, and ionic strength (MP4)Self-regulated switch responding to humidity change (MP4)Adaptive grippers that can quickly grasp a hot metal rod or a hot metal wire ball with the PANi–PNIPAm layer in contact with the hot object (MP4)This article has not yet been cited by other publications.

Harnessing the Power of Stimuli‐Responsive Polymers for Actuation

Biomimetic Soft Actuator: Rapid Response to Multiple Stimuli with Programmable Control

Bioinspired Stimuli-Responsive Materials for Soft Actuators.

Stimuli-Responsive Polymer Actuator for Soft Robotics

Biomimetic Stimulus Responsiveness: From Materials Design to Device Integration

Nature-inspired strategies for the synthesis of hydrogel actuators and their applications

Stimuli responsive actuators: recent advances

Stimuli-Responsive Polymers for Sensing and Reacting to Environmental Conditions

Programmable Multistimuli-Responsive and Multimodal Polymer Actuator Based on a Designed Energy Transduction Network

Research progress on conductive polymer actuators: Mechanisms, performance improvement, and applications

Research Progress and Emerging Directions in Stimulus Electro-Responsive Polymer Materials

Smart Actuators Based on External Stimulus Response

Design, Regulation, and Applications of Soft Actuators Based on Liquid-Crystalline Polymers and Their Composites

Bioactuators Based on Stimulus-Responsive Hydrogels and Their Emerging Biomedical Applications

Organic Molecule‐Driven Polymeric Actuators

Stimuli-responsive Functional Materials for Soft Robotics

Stimuli-Responsive Polymers at the Interface with Biology

Self‐healing polymers for soft actuators and robots

Light-Driven Soft Actuators Based On Photoresponsive Polymer Materials

Emerging applications of stimuli-responsive polymer materials

Biological Stimuli-responsive Polymer Systems: Design, Construction and Controlled Self-assembly