Abstract:Consumption of rare-earth metal (REM) oxides, such as cerium and lanthanum, is significantly lower than their production. This discrepancy is attributed to the complex extraction of all REMs, where the share of cerium is approximately 40%. This article proposes a method for processing REM oxides for their use as master alloys in ferrous metallurgy products. REMs, in the form of modifiers for steels and alloys, are widely used. However, despite their wide usage, owing to the complexity of the REM production technology, they tend to have a high market value. This study explores the preparation of a cerium carbide (CeC 2 ) master alloy for the modification of steels and cast irons. The proposed method aims to reduce the cost of the alloying process and simultaneously increase the demand for REM oxides. Using a high-temperature synthesis process, CeC 2 was obtained for the modification of steel and cast iron. For this purpose, cerium dioxide (CeO 2 ), graphite (C), and ARMCO-iron (Fe) were mixed in a specific percentage ratio by weight: 5.4% C, 19.5% CeO 2 , and 75.1% Fe. Following this, the reaction mixture was heated in a furnace to a temperature of 1650°C and held for 30 min, with a residual pressure in the furnace of 10 –1 mbar. The synthesis was performed in the temperature range of 1300–1650°C, with the highest reaction rate of at a temperature of 1520°C. Both elemental and X-ray diffraction analyses indicated that CeO 2 was the end product of the synthesis process. The master alloy does not undergo hydrolysis because CeC 2 is synthesized in the liquid phase of iron. It has been established that the technology for producing a cerium carbide alloy involving high-temperature heating in a resistive furnace, enables the production of a material with reproducible properties.

Preparing Process of Cerium Acetate and Rare Earth Acetate

Preparation of Ceria with Large Particle Size and High Appearance Density

Preparation of Ceric Hydroxide Through Transformation of Cerium Compounds

Preparation of Ammonium Cerium Phosphate via Low‐heating Solid State Reaction and Its Catalysis for Benzyl Acetate Synthesis

Effect of acetate ions and pH on the morphology of cerium oxide nanoparticles

Chelating Ligand-Mediated Crystal Growth Of Cerium Orthovanadate

Synthesis of N-butyldiacetylimide and Extraction for Ce(Ⅳ)

Preparation of High-Purityand White CeO_2 by Complex-Precipitation Method and Its Photocatalytic Activit

Preparation of CeO2 Microspheres by Internal Gelation Process with Copolymerization Using Acrylic Acid

Electrosynthesis of Cerium Containing Silicon Acrylate Coatings with Antifouling and Corrosion Resistant Properties

INFLUENCE OF PRECIPITANTS ON STRUCTURE OF COLLOIDAL SOLUTION SPRAY PYROLYSIS DERIVED Sm_(0.2)Ce_(0.8)O_(1.9) SOLID ELECTROLYTE

Synthesis of porous silica gel and study on the adsorption of cerium

Preparation, Characterization and Catalytic Properties of Yttrium-Zirconium-Pillared Montmorillonite and Their Application in Supported Ce Catalysts

Preparation of cerium dioxide microspheres by internal gelation with cerium citrate as precursor

Synthesis and performances of nano-sized neodymium oxide

Wet chemical preparation of well-dispersed colloidal cerium oxide nanocrystals

Homogeneous Precipitation of Lanthanide Oxalates

Redox Assisted Solvent Extraction to Enable Highly Efficient Separation of Cerium from Other Lanthanides: Experimental Studies and DFT Calculations

Electrochemical study of reduction Ce(III) ions and production of high purity metallic cerium by electrorefining in fused LiCl-KCl eutectic

Selective Recovery of Cerium as High-Purity Oxides via Reactive Separation Using CO 2 -Responsive Structured Ligands

Processing of Rare Earth Metal Oxide for Use as a Master Alloy in the Metallurgical Industry