Abstract:The superconducting magnet group at IHEP (the Institute of High Energy Physics, Chinese Academy of Sciences, China) has been engaging in the R&D of high field accelerator magnets since 2014 for the pre-study of the next-generation high energy particle accelerators like CEPC-SPPC (Circular Electron Positron Collider-Super Proton Proton Collider), FCC (Future Circular Collider), etc. A superconducting model dipole magnet named LPF1 was first fabricated with NbTi and Nb 3 Sn in a combined common-coil configuration in 2017 and tested in 2018, a main field of 10.23 T was reached within two 10 mm apertures. The magnet was reassembled with higher pre-stress in 2019 to investigate the influence of the pre-stress loading level on the performance of common-coil dipole magnets. The main field of this upgraded magnet named LPF1-S was increased to 10.71 T within two 12 mm apertures. By improving the key processing technologies in Rutherford cable fabrication, coil winding, Nb 3 Sn & NbTi splices soldering and coil impregnation, the recently fabricated model dipole magnet named LPF1-U attained a 12.47 T main field in two 14 mm apertures in 2021. To fully take advantage of Nb 3 Sn and NbTi superconductors in different field regions, LPF1-U was still designed and developed with a combined coil configuration with Nb 3 Sn for the inner two coils and NbTi for the outer four coils. Additionally, graded coil topology and different coil LSS (length of straight section) settings were adopted in the optimization of LPF1-U layouts. Bladder and key technology was used for the support structure, and fiber optic sensors based on FBG (fiber Bragg grating) were utilized to monitor the stress distribution and variation in the structures and coils through the whole process from magnet assembly to cool-down and excitation. During the performance test, a relatively large number of trainings were carried out and LPF1-U became more stable after the thermal cycle. A peak field of 12.7 T in the coils (12.47 T main field in apertures) corresponds to an operating current of 6865 A and a load line ratio of 90% was finally attained. It is worth mentioning that LPF1-U is the first hybrid—Nb 3 Sn, NbTi—common coil dipole magnet that has achieved a main field of more than 12 T in two apertures. The design, fabrication and performance analysis of the LPF series dipole magnets are presented in this paper.

Design and Measurement of a New Superbend-Magnet for WALS

Three Dimensional Compensation Spherical Coils for Compact Atomic Magnetometers

Electromagnetic Design Study of a Superconducting Longitudinal Gradient Bend Magnet Based on the HALF Storage Ring

Design and Test of a 90-T Nondestructive Magnet at the Wuhan National High Magnetic Field Center

Mechanical Design, Assembly and Strain Measurement Results of a 13-T Superconducting Dipole Magnet

The Limited B-Field Integral of Superconducting Longitudinal Gradient Bend Magnet

Design and Test of A Short Mockup Magnet for the Superconducting Undulator at the Ssrf

Design and Performance of the First Dual-Coil Magnet at the Wuhan National High Magnetic Field Center

Research on Tension-Free Bending of 15 T DC Magnet

Development of Superconducting Model Dipole Magnets Beyond 12 T with a Combined Common-Coil Configuration

Short and Long Pulse High Magnetic Field Facility at the Wuhan National High Magnetic Field Center

Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet with Graded Common-Coil Configuration

Concept Design of 100 T Pulsed Magnet at the Wuhan National High Magnetic Field Center

Development of YBCO Insert for a 25 T All Superconducting Magnet

Structural design and test of superconducting magnet coil for the cooling storage ring external-target experiment

The Magnet Design for the HLS Storage Ring Upgrade Project

Design of a large-scale superconducting dipole magnet for the CEE spectrometer

Development of Testing Device for Critical Current Measurements for HTS/LTS

Structural Design of DC Magnet for Super-X Test Facility

Strain analysis and preliminary test of an all-superconducting high-field magnet generating 32.4 T direct-current magnetic field

Development of a 1/2-length prototype high field Nb3Sn magnet for the 4th generation ECR ion source