Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

A Description of a D-3He Fusion Reactor Based on a Dipole Magnetic Field

A D-3He Fusion Reactor Based on a Dipole Magnetic Field

Extremum-Seeking-Based Receding-Horizon Optimal Control of Plasma Current Profile in the DIII-D Tokamak

Direct Numerical Simulation of Unstable Stratified Turbulent Flow under a Magnetic Field

Concepts for a deuterium-deuterium fusion reactor

Magnetic field generation from composition gradients in inertial confinement fusion fuel

Complete and robust magnetic field confinement by superconductors in fusion magnets

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Direct numerical simulation of turbulent mixed convection in a vertical channel in a wall-normal magnetic field

Poloidal magnetic field in the dense plasma focus

Stable Deuterium-Tritium plasmas with improved confinement in the presence of energetic-ion instabilities

Stable Deuterium-Tritium burning plasmas with improved confinement in the presence of energetic-ion instabilities

Simulation of self-generated magnetic fields in an inertial fusion hohlraum environment

A novel plasma source concept for negative ion generation in neutral beam injectors for fusion applications

D-Mag: a laboratory for studying plasma physics and diagnostics in strong magnetic fields

Confinement and Heating of a Deuterium-Tritium Plasma

Theoretical Study of the D-T Fuel Burning Rate in Z-Pinch Facilities with Magneto-Inertial Confinement

Physics design point of high-field stellarator reactors

A research program to measure the lifetime of spin polarized fuel

Maximum entropy states of collisionless positron-electron plasma in a dipole magnetic field

Study of the Pure Deuterium Fuel Burning Rate in Z-Pinch Devices with Magneto-Inertial Confinement