Abstract:It is essential to study the tensile fracture mechanism of additively manufactured materials and develop the effective process treatment techniques to improve their fracture resistance. In this paper, the effects of different treatment processes on the microstructure and tensile fracture properties of TC17 titanium alloy melted by laser selective zone melting were investigated. The static tensile fracture morphological characteristics were observed by combining SEM and EDS. The metallographic microstructure after chemical corrosion was observed optically. And the tensile fracture morphology of the three states of TC17 titanium alloy samples at room temperature conditions was investigated. The results show that the metallographic matrix microstructure of TC17 titanium alloy after HT, HIP and HIP-HT treatments was a bimodal structure with α+β phases, i.e., β phase was in the form of a net basket, and α phase was in the form of a coarse bar. The grain sizes of the samples treated by different processes were different, but the difference in grain size of the HT-treated tissues was small, and the difference in grain size of the HIP-HT-treated tissues was large. And the coarse α-phase segregation could be seen at the edge of the samples. The 3D-printed materials had complex changes in anisotropic properties affected by the printing structure and tissue. The printed tissues were brittle and had high internal stresses. These problems were partly improved at high temperatures, but they still existed. The HIP-HT-treated materials had a large α+β-phase bimodal structure. The HT-treated material had coarse grains and precipitation phases, poor room temperature plasticity, and improved high temperature plasticity. After HT treatment, the original printing microstructure changed, the strength and plasticity were significantly improved, but the macroscopic printing structure still had a slight influence on the fracture morphology. When HIP treatment temperature was higher, the influence of macroscopic printing structure basically disappeared, but the grain and microstructure grew up, and the strength and plasticity were slightly lower than that of the HT treatment. HIP process basically eliminated the unfused defects of the three-dimensional morphology, and the local weak bonding zone formed.

Microstructure Evolution of Ti17 Titanium with Ultrahigh Strength and Moderate Plasticity Fabricated by Laser Powder Bed Fusion

Microstructure and Mechanical Properties of An Ultrahigh-strength Titanium alloy Ti-4.5Al-5Mo-5V-6Cr-1Nb Prepared Using Laser Directed Energy Deposition and Forging: A Comparative Study

Microstructure evolution and mechanical property of a new multi-component β titanium alloy with ultrahigh strength above 1350 MPa

Microstructure Evolution and High Strength-Ductility Synergy of Ti-13Nb-13Zr-2Ta Alloy Fabricated by Laser Powder Bed Fusion

Microstructural evolution and cryogenic-normal temperature deformation behavior of the near-α titanium alloy TA15 fabricated by laser powder bed fusion

Tailoring the microstructure and mechanical property of laser powder bed fusion fabricated Ti–6Al–2Sn–4Zr–2Mo via heat treatment

Microstructure and mechanical evolution behavior of LPBF (laser powder bed fusion)-fabricated TA15 alloy

Effect of Solution Aging Heat Treatment on Microstructure Evolution and Properties of TC17 Titanium Alloy Formed by Laser Solid Forming

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Microstructure Tailoring for High Strength Ti-6Al-4V without Alloying Elements through Optimized Preheating and Post-Heating Laser Scanning in Laser Powder Bed Fusion

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Effects of different treatment processes on microstructure and tensile fracture behaviour of selected laser melting TC17 titanium alloy

Innovative Fabrication Design for In Situ Martensite Decomposition and Enhanced Mechanical Properties in Laser Powder Bed Fused Ti6Al4V Alloy

The Reverse Transformation Mechanism of Β Phase and Its Stability of Ti-6Al-4V Alloy Fabricated Via Laser Powder Bed Fusion

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Additive Manufactured Ti-6.5Al-2Zr-1Mo-1V Alloy

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

Optimization of the Post-Process Heat Treatment Strategy for a Near-α Titanium Base Alloy Produced by Laser Powder Bed Fusion

Microstructure and Corrosion Resistance of Ti6Al4V Manufactured by Laser Powder Bed Fusion

Influence of laser treatment on the microstructural evolution and performance of Ti65 alloy

Investigation on the Microstructure and Mechanical Properties of the Ti-Ta Alloy with Unmelted Ta Particles by Laser Powder Bed Fusion