Abstract:The reasonable delay time of millisecond-delay blasting using digital electronic detonators can significantly reduce the vibration effects induced by tunnel blasting. This study proposes a method for calculating the delay time for cut holes, easer holes and periphery holes, considering the rocks breaking effect as well as wave superposition theory. And then according to the actual layout diagram of the tunnel holes, the delay time calculation formulas of different holes are put forward. Then the delay times were calculated according to the formulas and applied in the field tests. The velocities, rocks breaking and wave superposition cancellation of the vibration using different delay times are analyzed with digital electronic detonators. Then the optimum delay times of different holes were obtained and applied to New Hongyan tunnel project. The velocity and frequency of the vibration with digital electronic detonators are analyzed, compared with non-electronic detonators. The effects of charge and delay time on the velocity and principal frequency of a blasting seismic wave are discussed. The results indicate that the delay time for the holes must be prioritized to achieve breaking effects in the rock with the simultaneous formation of a new free surface, next considering the wave superposition cancellation. When the delay time of cut holes was 5 ms, the rocks breaking effect and wave superposition cancellation effect both worked well. The velocity of the vibration induced by the cut holes blasting was about only 0.46-0.51 cm/s. When the delay time was 6 ms or much longer, the rocks breaking effect would fail. With regard to the easer holes and periphery holes, the optimum delay time of them were all 5ms. The vertical peak particle velocity was reduced from 2.974 cm/s to 0.901 cm/s with digital electronic detonators. Therefore, the velocity had decreased by 69.70% than non-electronic detonators, which was caused by reducing the single simultaneous explosive charge and setting optimum delay time. The proposed delay time calculation method is demonstrated to be sufficiently accurate and can thus be used as a guideline to reduce tunnel blasting vibrations.

Characteristics of Blasting Vibration Induced by Short-Delay Cylindrical Charges Based on Heelan Model

Study on Blast-Induced Vibration of Single-Hole Cylindrical Charge

Experimental and Numerical Investigation of Blast-Induced Vibration for Short-Delay Cut Blasting in Underground Mining

Effects of Charge Length on Single Long-Hole Blasting Vibration Characteristics with Consideration of the Free Surface

Assessment of Induced Vibrations Derived from the Wave Superposition in Time-Delay Blasts

Influence of Depth and Position of Vibration-Isolating Slot on Damping Effect of Blasting Vibration

Delay Time Optimization in Blasting Operations for Mitigating the Vibration-Effects on Final Pit Walls' Stability

Short-delay Blasting with Single Free Surface: Results of Experimental Tests

Experimental Study of Blast-Induced Vibration Characteristics Based on the Delay-Time Errors of Detonator

Experimental investigations of the effect of millisecond-delay time on the blast vibration reduction with electronic detonators

SHI Xiuzhi1，QIU Xianyang1，ZHOU Jian1，WANG Yang1，NIE Jun1，LI Bihong2

Attenuation Characteristics of Blasting Stress under Decoupled Cylindrical Charge

Tunnel millisecond-delay controlled blasting based on the delay time calculation method and digital electronic detonators to reduce structure vibration effects

Frequency Comparison of Blast-Induced Vibration Per Delay for the Full-Face Millisecond Delay Blasting in Underground Opening Excavation

Attenuation Assessment of Blast-Induced Vibrations Derived from an Underground Mine

Reduction of Blasting Induced Ground Vibrations Using High-Precision Digital Electronic Detonators

Influence of initiation modes on vibration frequency induced by single-hole blasting

Determination and application study of optimal delay time for tunnel millisecond blasting based on interference vibration reduction method

Identifying Delay Time of Detonator for a Millisecond Blasting

Influence of Detonator Delay Scatter on Rock Fragmentation by Bunch-Holes Blasting

A new approach to reduce blasting-induced vibration in tunnel blasting by utilizing the initiation time scatter of detonator