Abstract:Developing novel catalysts with high efficiency and selectivity is critical for enabling future clean energy conversion technologies. Interfaces in catalyst systems have long been considered the most critical factor in controlling catalytic reaction mechanisms. Interfaces include not only the catalyst surface but also interfaces within catalyst particles and those formed by constructing heterogeneous catalysts. The atomic and electronic structures of catalytic surfaces govern the kinetics of binding and release of reactant molecules from surface atoms. Interfaces within catalysts are introduced to enhance the intrinsic activity and stability of the catalyst by tuning the surface atomic and chemical structures. Examples include interfaces between the core and shell, twin or domain boundaries, or phase boundaries within single catalyst particles. In supported catalyst nanoparticles (NPs), the interface between the metallic NP and support serves as a critical tuning factor for enhancing catalytic activity. Surface electronic structure can be indirectly tuned and catalytically active sites can be increased through the use of supporting oxides. Tuning interfaces in catalyst systems has been identified as an important strategy in the design of novel catalysts. However, the governing principle of how interfaces contribute to catalyst behavior, especially in terms of interactions with intermediates and their stability during electrochemical operation, are largely unknown. This is mainly due to the evolving nature of such interfaces. Small changes in the structural and chemical configuration of these interfaces may result in altering the catalytic performance. These interfacial arrangements evolve continuously during synthesis, processing, use, and even static operation. A technique that can probe the local atomic and electronic interfacial structures with high precision while monitoring the dynamic interfacial behavior in situ is essential for elucidating the role of interfaces and providing deeper insight for fine-tuning and optimizing catalyst properties. Scanning transmission electron microscopy (STEM) has long been a primary characterization technique used for studying nanomaterials because of its exceptional imaging resolution and simultaneous chemical analysis. Over the past decade, advances in STEM, that is, the commercialization of both aberration correctors and monochromators, have significantly improved the spatial and energy resolution. Imaging atomic structures with subangstrom resolution and identifying chemical species with single-atom sensitivity are now routine for STEM. These advancements have greatly benefitted catalytic research. For example, the roles of lattice strain and surface elemental distribution and their effect on catalytic stability and reactivity have been well documented in bimetallic catalysts. In addition, three-dimensional atomic structures revealed by STEM tomography have been integrated in theoretical modeling for predictive catalyst NP design. Recent developments in stable electronic and mechanical devices have opened opportunities to monitor the evolution of catalysts in operando under synthesis and reaction conditions; high-speed direct electron detectors have achieved sub-millisecond time resolutions and allow for rapid structural and chemical changes to be captured. Investigations of catalysts using these latest microscopy techniques have provided new insights into atomic-level catalytic mechanisms. Further integration of new microscopy methods is expected to provide multidimensional descriptions of interfaces under relevant synthesis and reaction conditions. In this Account, we discuss recent insights on understanding catalyst activity, selectivity, and stability using advanced STEM techniques, with an emphasis on how critical interfaces dictate the performance of precious metal-based heterogeneous catalysts. The role of extended interfacial structures, including those between core and shell, between separate phases and twinned grains, between the catalyst surface and gas, and between metal and support are discussed. We also provide an outlook on how emerging electron microscopy techniques, such as vibrational spectroscopy and electron ptychography, will impact future catalysis research.

Ultimate structures in catalysis: Single atoms, subnano-clusters, and electrons

Isolating Single and Few Atoms for Enhanced Catalysis

Structural regulation with atomic-level precision: From single-atomic site to diatomic and atomic interface catalysis

Atomically Precise Noble Metal Nanoclusters as Efficient Catalysts: A Bridge between Structure and Properties

Catalysis in Single Crystalline Materials: from Discrete Molecules to Metal-Organic Frameworks

Single-Atom Catalysts: from Design to Application

Structure Design and Electrochemical Properties of Carbon-Based Single Atom Catalysts in Energy Catalysis: A Review

Structural Engineering of Atomic Catalysts for Electrocatalysis.

Structural Regulation and Support Coupling Effect of Single‐Atom Catalysts for Heterogeneous Catalysis

Single-Atom Engineering to Ignite 2D Transition Metal Dichalcogenide Based Catalysis: Fundamentals, Progress, and Beyond

Electrocatalyst Engineering and Structure-Activity Relationship in Hydrogen Evolution Reaction: from Nanostructures to Single Atoms

Atomic‐level synergistic catalysts: single‐atom site integrated with atom, cluster and nanoparticle

Atomic Scale Materials for Emerging Robust Catalysis

Discovery of Electronic Structure and Interfacial Interaction Features in Catalytic Activity

Hollow Microstructural Regulation of Single-Atom Catalysts for Optimized Electrocatalytic Performance

Structural Design of Metal Catalysts Based on ZIFs: from Nanoscale to Atomic Level

Interfaces in Heterogeneous Catalysts: Advancing Mechanistic Understanding through Atomic-Scale Measurements

Atomically Dispersed Catalysts: Precise Synthesis, Structural Regulation, and Structure–Activity Relationship

Pt-Based electrocatalysts with high atom utilization efficiency: from nanostructures to single atoms

Advances in the understanding of the structure–performance relationships of 2D material catalysts based on electron microscopy