Abstract:In this paper, the evolution of microstructure in Fe–Ni–Co–Al polycrystalline alloys and its effects on mechanical properties were systematically investigated. The results show that the proportion of high-angle grain boundaries (HAGBs) is 98.1 % with 51.2 % of Σ3 GBs during the solid solution (SS) process. The distribution of Σ3 GBs and other HAGBs (non-Σ3 HAGBs) are relatively dispersed, which prevents the formation of a specific orientation. In addition, there is no discernible anisotropy in GB migration during the SS process, ultimately resulting in the absence of texture. In contrast, during the directional recrystallization (DR) process, the directional migration of GBs is driven by the temperature gradient. Random high-angle grain boundaries (RHAGBs) with Σ values exceeding 29 possess higher GB energy and migration rate compared to low-angle grain boundaries (LAGBs) and HAGBs, making them more susceptible to GB migration. In the grain incubation area, the proportion of RHAGBs between grains oriented {111}<214> (grain 2 and grain 5) and their surrounding grains are 90 % and 75 %. These grains have the growth advantage and eventually form the main orientation {111}<214>. While the proportion of RHAGBs between grains oriented {114}<214> (grain 11) and its surrounding grains is only 65 %, characterized by lower GB energy and migration rate. Therefore, these grains eventually form the minor orientation {114}<214>. The coherent L12-Ni3Al (γ′) precipitates were observed in both the SS-AG (SS after aging) and DR-AG (DR after aging) treatments. The DR-AG alloy, characterized by {111}<214> and {114}<214> orientations and γ′ precipitates, exhibited a 3.6 % recoverable strain and a 1.2 % superelastic strain, whereas no evident superelastic behavior was found in the SS-AG alloy, which featured a random texture and γ′ precipitates.

Effects of Ni Addition on Abnormal Grain Growth in Superelastic CuAlMnCoNi Alloy

Effect of Cu Addition on Abnormal Grain Growth in a FeMnAlNi-Based Superelastic Alloy

Refining Micron-Sized Grains to Nanoscale in Ni-Co Based Superalloy by Quasistatical Compressive Deformation at High Temperature

Effects of Cr on the Abnormal Grain Growth of Cu-Al-Mn-Ni-Cr Superelastic Alloy

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy

Effect of Grain Orientation and Precipitates on the Superelasticity of Fe–Ni–Co–Al Polycrystalline Alloys

Effect of Ni Addition on the Solidification Process and Microstructure of Al-12%Si-4% Cu-1.2%Mn-x%Ni Heat-Resistant Alloys

Effect of Ni addition on microstructure and mechanical properties of Al–Mg–Si–Cu–Zn alloys with a high Mg/Si ratio

Abnormal Grain Growth in Annealing Cast Cu–Al–Mn–V Alloys and Their Superelasticity

Abnormal grain growth in the Ni-based wrought superalloy GH4698 bar during heat treatment

The Effects of Nb Additions on the Microstructure Evolution in Cu–9Ni–6Sn Alloy

Effect of Ti content on abnormal grain growth of Fe-Mn-Al-Ni-Ti shape memory alloy

Unraveling the Formation Mechanism of Abnormally Large Grains in an Advanced Polycrystalline Nickel Base Superalloy

Effects of Ni Addition on the Microstructure and Properties of Nanostructured Copper–germanium Alloys

Superplasticity of Ni-rich single phase NiAl intermetallics with large grains

Effects of Strain Amount and Strain Rate on Grain Structure of a Novel High Co Nickel-Based Polycrystalline Superalloy

Enhanced Mechanical Properties of Polycrystalline Cu–Al–Ni Alloy Through Grain Boundary Orientation and Composition Control

The Evolution of Microstructure and Mechanical Properties at Elevated Temperature of Cast Al–Li–Cu–Mg Alloys with Ni Addition

Tensile Deformation Behavior of a New Ni-base Superalloy at Room Temperature

Effect of Cyclic Heat Treatment on Abnormal Grain Growth in Fe-Mn-Al-based Shape Memory Alloys with Different Ni Contents

Effects of Nb Addition on the Properties and Microstructure of Cu-Ni-Si-Mg Alloy