Abstract:al. report an f -TEG featuring a mushroom-like structure that achieves high output power density on human skin without external heat sink via thermal design. The work provides an example of the design process of f -TEGs and paves the pathway toward scalable fabrication of low-cost and high-performance f -TEGs. SUMMARY Flexible thermoelectric generators ( f -TEGs) are promising solutions to power supply for wearable devices. However, the high fabrication costs and low output power density of conventional f -TEGs limit their applications. Here, we present a bulk-material-based f -TEG featuring multifunctional copper electrodes for heat concentration and dissipation and fabrics for comfort and heat-leakage reduction. When worn on the forehead, our f -TEG’s maximum output power density (based on the device’s area) reaches 48 m W/cm 2 at a wind speed of 2 m/s and an ambient temperature of 15 (cid:1) C. A light-emit-ting diode (LED) powered by our f -TEG headband with 100 pairs of thermoelectric pillars can illuminate a paper for reading in a dark room at 17.5 (cid:1) C without an external heat sink or forced convection at the cold side. This work provides a general design approach for high-performance f -TEGs at a low cost. The device-level perspectives ﬁll the critical knowledge gap between state-of-the-art material innovations and practical thermoelectric applications. In summary, we demonstrate strategies to achieve a higher performance, body-powered f -TEG. We use multifunctional thin copper disks as electrodes, heat concentrators and spreaders, spacers, and ﬂexibility enablers. Copper spacers and fabrics are used to suppress the heat loss between the hot and the cold sides through conduction and convection and provide good wearability and comfort even in sweating conditions. We develop an analytical model that predicts an f -TEG’s en-ergy-harvesting performance and helps determine the optimal geometries of the thermoelectric unit in a given thermal environment. In contrast to most reported f -TEGs using thicker thermoelectric pillars to get a larger temperature difference across the pillars (so a larger thermoelectric voltage), our mushroom-like f -TEG’s performance stands out despite the small thickness of thermoelectric pillars (1.9 mm), reducing weight and cost of thermoelectric materials. In indoor testing, our f -TEG’s maximum output power density (based on the device area) on human skin reaches 16 m W/cm 2 at the ambient temperature of 15 (cid:1) C when there is little wind (v air = 0.2 m/s), and the output power density goes up to 48 m W/cm 2 when the wind speed is increased to 2 m/s. An LED powered by our f -TEG headband with 100 pairs of thermoelectric units can illuminate a paper for reading in a completely dark room at 17.5 (cid:1) C without an external heat sink or forced air convection at the cold side. Our f -TEG headband with 50 pairs of thermoelectric units can generate 1.2 mW power during a jog at the ambient temperature of 25 (cid:1) C (little wind and running at a speed of 2.5 m/s) in outdoor testing. Our device-level perspectives are critical to bridging state-of-the-art material research and practical thermoelectric applications. Although this paper focuses on power generation, such devices can also be used for personalized cooling. We envision our low-cost and high-perfor-mance

Performance Limits of Wearable Ink-Based Thin-Film Thermoelectric Generator for Human-Body Waste Heat Recovery

Design of a Wearable Thermoelectric Generator for Harvesting Human Body Energy

Design and Fabrication of Wearable Thermoelectric Generator Device for Heat Harvesting

Wearable Thermoelectric Generator with Copper Foam As the Heat Sink for Body Heat Harvesting

Comprehensive Performance Prediction and Power Promotion for Wearable Thermoelectric Generator with Flexible Encapsulation in Practical Application

Optimized thermal design for excellent wearable thermoelectric generator

Wearable thermoelectric generator for harvesting heat on the curved human wrist

Ionic Gelatin-Based Flexible Thermoelectric Generator with Scalability for Human Body Heat Harvesting

Evaluation of the Power-Generation Capacity of Wearable Thermoelectric Power Generator

High-Performance Wearable Bi2Te3-Based Thermoelectric Generator

Wearable thermoelectric generator to harvest body heat for powering a miniaturized accelerometer

An analytical model for wearable thermoelectric generators harvesting body heat: An opportunistic approach

Ambient-Temperature-Independent Power Generation in Wearable Thermoelectric Generator with CNTs/MoS 2 Solar Absorber

High‐performance Stretchable Organic Thermoelectric Generator via Rational Thermal Interface Design for Wearable Electronics

Operation of Wearable Thermoelectric Generators Using Dual Sources of Heat and Light

High-Power-Density Wearable Thermoelectric Generators for Human Body Heat Harvesting

High-performance, thin-film thermoelectric generator with self-healing ability for body-heat harvesting

High-performance, ﬂexible thermoelectric generator based on bulk materials

Flexible, self‐powered thermoelectric module for body‐heat recovery

High performance flexible thermoelectric generator using bulk legs and integrated electrodes for human energy harvesting

Simultaneous Realization of Flexibility and Ultrahigh Normalized Power Density in a Heatsink-Free Thermoelectric Generator via Fine Thermal Regulation