Abstract:In forest areas, when using interferometric synthetic aperture radar (InSAR) technique to extract subcanopy topography, a key problem is how to reduce the impact of the forest-scattering process on InSAR height measurements. In this paper, we propose a new methodology for subcanopy topography extraction by making full use of single-baseline TanDEM-X InSAR data. The interferometric phase is used to estimate a high-resolution and high-precision digital elevation model (DEM), and the coherence magnitude is used to extract the scattering phase center (SPC) height associated with canopy scattering. Allowing for the difference in the sensitivity of TanDEM-X bistatic interferometry information for forests with different densities, two scenarios are involved: (1) For pixels characterized by dense forest, the X-band SAR signal cannot penetrate through the forest canopy layer. In this case, an existing scattering model is used to estimate the InSAR penetration depth from the coherence magnitude. Note that when the penetration depth is small compared with the height of ambiguity (HoA), the former can be recognized as the difference between the InSAR DEM and the actual surface height. Some sparse forest heights (or SPC heights) measured by the Ice, Cloud, and land Elevation Satellite-2 (ICESAT-2) system are then used to help determine the linear relationship between penetration depth and sparse forest height (or SPC height). Finally the SPC can be estimated and removed from the TanDEM-X InSAR DEM. (2) For pixels characterized by sparse vegetation, the X-band likely penetrates the vegetation volume layer to ground level. For this scenario, a coherence threshold is set to identify these pixels, and the corresponding SPC heights can be considered zero where the subcanopy topography is approximately equal to the InSAR-generated DEM. The proposed method was validated by combining TanDEM-X coregistered single look slant range complex (CoSSC) data from two test sites with different forest types with ICESAT-2 points. The results are as follows. For the Krycklan test site, compared with the validation data, the RMSE varied from 7.76 m for the InSAR DEM to 3.22 m for the reconstructed subcanopy topography, which is an improvement of 58.5%. For the Oyan test site, subcanopy topography achieved an RMSE of 7.26 m compared with the RMSE of 27.12 m before SPC height correction, which represents an improvement of 80.1%. In addition, we investigated the impact of the topographic slope and the necessity of using the coherence threshold. For inconsistencies between TanDEM-X bistatic InSAR data and ICESAT-2 measured forest height over time, the fitting between penetration depth and SPC height calculated by ICESAT-2 subcanopy topographic elevation and InSAR-generated DEM can be used. These investigations confirm the feasibility and reliability of the proposed method.

High-resolution Sub-Canopy Topography Mapping Via TanDEM-X DEM Combined with Future P-band BIOMASS PolInSAR Data

Automated Estimation of Sub-Canopy Topography Combined with Single-Baseline Single-Polarization TanDEM-X InSAR and ICESat-2 Data

Estimation of subcanopy topography based on single-baseline TanDEM-X InSAR data

A Region-Based Method of Vegetation Coverage Extracting in Complex Terrain Areas Using Polarmetric SAR Data.

Digital terrain, surface, and canopy height model generation with dual-baseline low-frequency InSAR over forest areas

Forest Height Estimation Approach Combining P-Band and X-Band Interferometric SAR Data

Reconstruction and Evaluation of DEMs From Bistatic Tandem-X SAR in Mountainous and Coastal Areas of China

Underlying Topography Estimation over Forest Using Maximum a Posteriori Inversion with Spaceborne Polarimetric SAR Interferometry

Capabilities of BIOMASS Three-Baseline PolInSAR Mode for the Characterization of Tropical Forests

High Quality Large-Scale 3-D Urban Mapping with Multi-Master TomoSAR

SAR Tomography at the Limit: Building Height Reconstruction Using Only 3-5 TanDEM-X Bistatic Interferograms

Model-Based Biomass Estimation of a Hemi-Boreal Forest from Multitemporal TanDEM-X Acquisitions

Estimation of Canopy Height From a Multi-SINC Model in Mediterranean Forest With Single-Baseline TanDEM-X InSAR Data

Improved forest biomass estimation based on P-band repeat-pass PolInSAR data across different forest sites

Combining L-band Synthetic Aperture Radar backscatter and TanDEM-X canopy height for forest aboveground biomass estimation

Collaborative Estimation of Aboveground Forest Biomass Using P-Band and X-Band Interferometric Synthetic Aperture Radar Based on Feature Optimization

A Multibaseline Forest Height Inversion Method to Solve Three General Problems in P-Band Repeat-Pass PolInSAR Data

A New Snow Depth Retrieval Method by Improved Hybrid DEM Differencing and Coherence Amplitude Algorithm for PolInSAR

Deep Learning for Mapping Tropical Forests with TanDEM-X Bistatic InSAR Data

A Gradient-Constrained Morphological Operation for Retrieving Subcanopy Topography Over Densely Forested Areas From ICESat-2/ATL03 Data

Non-Local SAR Tomography for Large-Scale Urban Mapping