Abstract:Three-dimensional (3D) cell-printing has been emerging as a promising technology with which to build up human skin models by enabling rapid and versatile design. Despite the technological advances, challenges remain in the development of fully functional models that recapitulate complexities in the native tissue. Moreover, although several approaches have been explored for the development of biomimetic human skin models, the present skin models based on multistep fabrication methods using polydimethylsiloxane chips and commercial transwell inserts could be tackled by leveraging 3D cell-printing technology. In this paper, we present a new 3D cell-printing strategy for engineering a 3D human skin model with a functional transwell system in a single-step process. A hybrid 3D cell-printing system was developed, allowing for the use of extrusion and inkjet modules at the same time. We began by revealing the significance of each module in engineering human skin models; by using the extrusion-dispensing module, we engineered a collagen-based construct with polycaprolactone (PCL) mesh that prevented the contraction of collagen during tissue maturation; the inkjet-based dispensing module was used to uniformly distribute keratinocytes. Taking these features together, we engineered a human skin model with a functional transwell system; the transwell system and fibroblast-populated dermis were consecutively fabricated by using the extrusion modules. Following this process, keratinocytes were uniformly distributed onto the engineered dermis by the inkjet module. Our transwell system indicates a supportive 3D construct composed of PCL, enabling the maturation of a skin model without the aid of commercial transwell inserts. This skin model revealed favorable biological characteristics that included a stabilized fibroblast-stretched dermis and stratified epidermis layers after 14 days. It was also observed that a 50 times reduction in cost was achieved and 10 times less medium was used than in a conventional culture. Collectively, because this single-step process opens up chances for versatile designs, we envision that our cell-printing strategy could provide an attractive platform in engineering various human skin models.

Engineering of Uniform Epidermal Layers Via Sacrificial Gelatin Bioink‐Assisted 3D Extrusion Bioprinting of Skin (adv. Healthcare Mater. 27/2023)

Engineering of Uniform Epidermal Layers Via Sacrificial Gelatin Bioink‐Assisted 3D Extrusion Bioprinting of Skin

Three-dimensional Bioprinting of a Full-Thickness Functional Skin Model Using Acellular Dermal Matrix and Gelatin Methacrylamide Bioink

3D printing of skin equivalents with hair follicle structures and epidermal-papillary-dermal layers using gelatin/hyaluronic acid hydrogels.

Sacrificial Microgel-Laden Bioink-Enabled 3D Bioprinting of Mesoscale Pore Networks

3D Bioprinting of Low-Concentration Cell-Laden Gelatin Methacrylate (gelma) Bioinks with a Two-Step Cross-linking Strategy.

3D Cell Printing of in Vitro Stabilized Skin Model and in Vivo Pre-Vascularized Skin Patch Using Tissue-Specific Extracellular Matrix Bioink: A Step Towards Advanced Skin Tissue Engineering

Simple and robust 3D bioprinting of full-thickness human skin tissue

Direct 3D cell-printing of human skin with functional transwell system

Engineered-Skin of Single Dermal Layer Containing Printed Hybrid Gelatin-Polyvinyl Alcohol Bioink via 3D-Bioprinting: In Vitro Assessment under Submerged vs. Air-Lifting Models

Extrusion Bioprinting of Shear‐Thinning Gelatin Methacryloyl Bioinks

Protocols of 3D Bioprinting of Gelatin Methacryloyl Hydrogel Based Bioinks.

Fibrinogen-Based Bioink for Application in Skin Equivalent 3D Bioprinting

Three-dimensional printing alginate/gelatin scaffolds as dermal substitutes for skin tissue engineering

A potential dermal substitute using decellularized dermis extracellular matrix derived bio-ink

Fabrication of SA/Gel/C scaffold with 3D bioprinting to generate micro-nano porosity structure for skin wound healing: a detailed animal in vivo study

Decellularized matrix bioink with gelatin methacrylate for simultaneous improvements in printability and biofunctionality

Bioprinting: Extrusion Bioprinting of Shear‐Thinning Gelatin Methacryloyl Bioinks (Adv. Healthcare Mater. 12/2017)

3D-bioprinted GelMA/gelatin/amniotic membrane extract (AME) scaffold loaded with keratinocytes, fibroblasts, and endothelial cells for skin tissue engineering

Overview of Current Advances in Extrusion Bioprinting for Skin Applications

A 3D bioprinted decellularized extracellular matrix/gelatin/quaternized chitosan scaffold assembling with poly(ionic liquid)s for skin tissue engineering