Abstract:Recently, because of the complex international situation and combat environment in the future, the development and application of new concept weapons have raised higher performance requirements for manufacturing technologies. However, at present, most weapons are still prepared using traditional charging methods (cast curing, pressure casting, and melt casting), which require subtractive manufacturing (SM) treatments before use. At present, the demand for weapon products is shifting towards reactive micro structures, high preparation efficiency, miniaturization, and controllable energy release. Besides, the modern “energetic-on-a-chip” trend was expected to reduce size and cost while increasing safety and maintaining performance. In this case, the traditional charging methods were not preferred due to their inherent drawbacks, such as being limited to the model, requiring long solvent drying times and recycling required and pores/cracks caused by the shrinkage of slurry, and so on. Therefore, it is necessary to innovate the processing and manufacturing technology of weapons and address the boundaries of existing charging methods, and this will enable the precise customization of high-quality energetic materials and avoid many defects. Additive manufacturing (AM), or 3D printing technology, has been booming recently. The application of additive manufacturing technology in the field of energetic materials (EMs) can promote the innovation of manufacturing technology for EMs and regulate the microstructure. Additionally, 3D printing technology can break through the existing design and development mode, expand explosive charging technology, and enable the distribution of different types of explosives and explosive density in a specific space area. Besides, 3D printing can fabricate “reactive microstructures” (RMS), which offer a deeper understanding of the EMs’ combustion and detonation phenomena at the micro- and nanoscale. Thus, the explosive/propellant grains with multiple damage modes can be designed and manufactured. This paper aims to summarize the current progress in the 3D printing of EMs, analyze the corresponding mechanisms, and provide guidance for future research.

Rheological and Printability Evaluation of Melt-Cast Explosives for Fused Deposition Modeling (FDM) 3D Printing

Preparation of TNT/HMX-based Melt-Cast Explosives with Enhanced Mechanical Performance by Fused Deposition Modeling (FDM)

Simulation of Printer Nozzle for 3D Printing TNT/HMX Based Melt-Cast Explosive

Effect of Printing Parameters on the Surface Roughness of 3D-Printed Melt-Cast Explosive Substitutes Based on Melt Extrusion Technology

3D Printable Elastomers with Exceptional Strength and Toughness

Rheological Behavior of DNP/HMX Melt-Cast Explosives with Bimodal and Trimodal Particle-Size Distributions

3D printing of RDX-based aluminized high explosives with gradient structure, significantly altering the critical dimensions

Experimental Investigation of Quasi‐Static Compressive Properties of Polymer‐Bonded Explosives (PBX) Based on UV‐Curing 3D Printing

The effect of micro-nano TKX-50 particle gradation on the properties of TNT based castable explosives

Energetic materials in 3D: an in-depth exploration of additive manufacturing techniques

3D Printing Injection Theory and Simulation Analysis of PBX Explosive

Application of TNBA-based Low Eutectic Mixture in Melt-Cast Explosives

Study on Explosive Welding A1060/3D-Printed-SUS316L

On rheology of mortar with recycled fine aggregate for 3D printing

Characterization of RDX-Based Thermosetting Plastic-Bonded Explosive by Cone-Beam Microfocus Computed Tomography

Rheological Properties and Printability Evaluation of 3d Printing Mortar with Recycled Powder

Influence of 3D-printed polymer structures on dynamic splitting and crack propagation behavior of cementitious tailings backfill

Promising Energetic Melt-Castable Material with Balanced Properties

Equal-Material Manufacturing of a Thermoplastic Melt-Cast Explosive Using Thermal-Pressure Coupling Solidification Treatment Technology

Performance evaluation on particle‐reinforced rigid/flexible composites via fused deposition modeling 3D printing

Rheological and Mechanical Characterization of 3D-Printable Solid Propellant Slurry