Abstract:The lack of comprehensive insight and accurate description on the dynamic thermomechanical behaviors in high-temperature and high-strain-rate loading environment could be one of the major obstacles to extend the laser metal deposited (LMD) Inconel 718 to engineering applications in aeroengine. In this study, to obtain in-depth understanding of plastic flow behavior of the LMD Inconel 718, uniaxial compressive experiments were conducted over a wide range of temperature (298-1273 K) and strain rate (0.001-5300/s). Based on a great number of experimental results, not only the anisotropy of compressive property, but the dependence of the plastic flow stress on temperature and strain rate were investigated systematically. The flow stress of the as deposited alloy in laser scanning direction is higher than that in depositing direction, which is attributed to the columnar grains epitaxially growing along the build direction and featuring the high length-diameter ratio within the as-deposited sample. Since the small-size precipitates in the under-aged (as-deposited) Inconel 718 alloy could be cut by the moving dislocations directly during plastic deformation, they have various effect on the interaction between moving dislocations and interstitial elements at different strain rate. The third-type of strain aging (3rd SA) effect, exhibiting an anomalous bell-shaped flow stress vs. temperature relation, was observed more apparently than that in the post-aged Inconel 718 reported by other literatures. As for the strain-rate effect, the flow stress of the alloy exhibits inconspicuous strain-rate sensitivity over the range of strain rate below similar to 10(3)/s, while increases sharply with the strain rate once it exceeds similar to 10(3)/s. Finally, taking into account the mechanical anisotropy, as well as the anomalous temperature and strain rate sensitivities of the flow stress, we developed a constitutive model based on a physical frame. In this model, an anisotropy component was introduced to consider the effective size of columnar grains in the corresponding loading direction, the strain rate hardening was enhanced as the strain rate gets close to a certain level, and a normal distribution with temperature was used to describe the 3rd SA effect. The developed model was shown to be able to accurately reproduce the plastic flow behavior of the LMD Inconel 718 over a wide range of temperature and strain rate.

Establishment and Application of an Internal-Variable-Based Constitutive Model for the Superplastic Deformation of Inconel 718 Alloy

New Constitutive Model for High-Temperature Deformation Behavior of Inconel 718 Superalloy

MICROSTRUCTURE EVOLUTION MECHANISM BASED CRYSTAL-PLASTICITY CONSTITUTIVE MODEL FOR NICKEL-BASED SUPERALLOY AND ITS FINITE ELEMENT SIMULATION

Modeling and Simulation of Dynamic Recrystallization for Inconel 718 in the Presence of Δ Phase Particles Using a Developed Cellular Automaton Model

Cyclic Plasticity Modeling of Nickel-Based Superalloy Inconel 718 under Multi-Axial Thermo-Mechanical Fatigue Loading Conditions

A Crystal Plasticity Based Constitutive Model for the Temperature Dependent Anomalous Behaviors of Nickel-Based Single-Crystal Superalloy

A Two-Stage Constitutive Model and Microstructure Evolution Simulation of a Nickel-Based Superalloy During High Temperature Deformation

Constitutive Model Based on Dynamic Recrystallization Behavior During Thermal Deformation of a Nickel-Based Superalloy

Microstructure-Based Flow Stress Model to Predict Machinability of Inconel 718

Length-Scale-Dependent Micromechanical Modeling for Precipitate Hardening in Inconel 718 Superalloy

A Microstructure-Based Constitutive Model Accounting for Rate Dependence of Superelastic NiTi Alloy under Cyclic Deformation

Thermomechanical Behavior of Laser Metal Deposited Inconel 718 Superalloy over a Wide Range of Temperature and Strain Rate: Testing and Constitutive Modeling

Physical Based Constitutive Model for the Prediction of Plastic Deformation of Fe‐Cr‐Ni Stainless Steel Under High Strain Rate

High‐Temperature Mechanical Behavior Assessment based on a Developed Constitutive Model of Inconel 718 Fabricated by Selective Laser Melting

Dislocation density‐based constitutive model for cyclic deformation and softening of Ni‐based superalloys

A Novel Unified Dislocation-Density Based Model for Hot Deformation Behavior of a Nickel-Based Superalloy

Deformation Behavior of Selective Laser-Melted Inconel 718 Superalloy

A Unified Dislocation Density-Based Model for an Aged Polycrystalline Ni-based Superalloy Considering the Coupled Effects of Complicate Deformation Mechanisms and Initial Δ Phase

An innovative constitutive material model for predicting high temperature flow behaviour of inconel 625 alloy

Microstructure Characteristics and Comparative Analysis of Constitutive Models for Flow Stress Prediction of Inconel 718 Alloy

Research on microplastic deformation of Inconel718 under the conditions of high temperature and high strain rate