Abstract:This study examines and quantifies the effect of adding polyelectrolytes to cellulose nanofibre suspensions on the gel point of cellulose nanofibre suspensions, which is the lowest solids concentration at which the suspension forms a continuous network. The lower the gel point, the faster the drainage time to produce a sheet and the higher the porosity of the final sheet formed. Two new techniques were designed to measure the dynamic compressibility and the drainability of nanocellulose–polyelectrolyte suspensions. We developed a master curve which showed that the independent variable controlling the behaviour of nanocellulose suspensions and its composite is the structure of the flocculated suspension which is best quantified as the gel point. This was independent of the type of polyelectrolyte used. At an addition level of 2 mg/g of nanofibre, a reduction in gel point over 50 % was achieved using either a high molecular weight (13 MDa) linear cationic polyacrylamide (CPAM, 40 % charge), a dendrimer polyethylenimine of high molecular weight of 750,000 Da (HPEI) or even a low molecular weight of 2000 Da (LPEI). There was no significant difference in the minimum gel point achieved, despite the difference in polyelectrolyte morphology and molecular weight. In this paper, we show that the gel point controls the flow through the fibre suspension, even when comparing fibre suspensions with solids content above the gel point. A lower gel point makes it easier for water to drain through the fibre network, reducing the pressure required to achieve a given dewatering rate and reducing the filtering time required to form a wet laid sheet. We further show that the lower gel point partially controls the structure of the wet laid sheet after it is dried. Halving the gel point increased the air permeability of the dry sheet by 37, 46 and 25 %, when using CPAM, HPEI and LPEI, respectively. The resistance to liquid flow was reduced by 74 and 90 %, when using CPAM and LPEI. Analysing the paper formed shows that sheet forming process and final sheet properties can be engineered and controlled by adding polyelectrolytes to the nanofibre suspension.

Effect of Pore Structure Regulation on the Properties of 3D Cellulose Nanofiber Electret Filtration Materials

Fabrication and performance of a new type of charged nanofiltration membrane based on polyelectrolyte complex

Toward High-Performance Fibrillated Cellulose-Based Air Filter Via Constructing Spider-Web-like Structure with the Aid of TBA During Freeze-Drying Process

Chemically Tailored Molecular Surface Modification of Bamboo Pulp Fibers for Manipulating the Electret Performance of Electret Filter Media

Study on the Structure and Properties of Cellulose-based Air Filter Material Controlled by Fibrillation

Electrospun 3D Curly Electret Nanofiber Air Filters for Particulate Pollutants

Preparation of ethyl cellulose bimodal nanofibrous membrane by green electrospinning based on molecular weight regulation for high-performance air filtration

A simple and effective approach to regulate and control pore structure of electrospun PTFE nanofiber membrane

Preparation of 3D Ethylcellulose-Based Electret Fiber Aerogel for Simulated Radioactive Aerosol Purification

Preparation of Cellulosic Air Filters with Controllable Pore Structures Via Organic Solvent-Based Freeze Casting: the Key Role of Fiber Dispersion and Pore Size

Preparation and characterization of electrospun cellulose acetate/poly(ethylene oxide) fiber membrane for air filtration

Engineering Cellulose Nanofibre Suspensions to Control Filtration Resistance and Sheet Permeability

Highly Efficient, Low-Resistant, Well-Ordered PAN Nanofiber Membranes for Air Filtration

Controllable Morphology of Electrospun Nanofiber Membranes with Tunable Groove Structure and the Enhanced Filtration Performance for Ultrafine Particulates

High Filterable Electrospun Nanofibrous Membrane with Charged Electret After Electrification Treatment for Air Filtration

Performance of Electrospun Polyvinylidene Fluoride Nanofibrous Membrane in Air Filtration

Enhanced Aerosol Particle Filtration Efficiency of Nonwoven Porous Cellulose Triacetate Nanofiber Mats

Simulation and experimental investigation of electret polypropylene fiber preparation via centrifugal melt electrospinning for enhanced air filtration

Effects of Polyethylene Glycol on the Structure and Performance of Cellulose Acetate Ultrafiltration Membrane

Fabrication, Polarization of Electrospun Polyvinylidene Fluoride Electret Fibers and Effect on Capturing Nanoscale Solid Aerosols

Effect of Pleat Structure on the Air Purification Performance of a Polytetrafluoroethylene/Poly(ethylene Terephthalate) Composite Membrane Filter