Abstract:In recent years, the rapidly growing consumption of fossil fuels negatively affects the environment and public health has attracted much attention. Much effort has been made to find a clean and renewable alternative energy. Bio-oil, produced by flash pyrolysis, is one of the more encouraging products for valorisation of biomass. It has been identified as a promising alternative energy source for fossil fuel owing to its outstanding characteristics such as higher energy density, more suitable for storage and transportation, less capital investment than any other products of biomass. However, the nature of bio-oil contains high acidity, strong corrosiveness, low heating value, thermal instability and chemical complexity, which severely restrict its wide range of applications as a high quality energy. Therefore, it is necessary to upgrade bio-oil. The upgrading techniques include steam reforming, esterification, emulsification, hydrodeoxygenation, catalytic pyrolysis etc. In this paper, catalytic pyrolysis experiments were performed in a fixed bed with inner diameter of 16mm and height of 380mm for bio-oil model compounds (diacetone alcohol, furfural, ethyl acetate and guaiacol) over different characteristics zeolites (HY, HZSM-5, ZSM-5, P/ZSM-5, La/ZSM-5, Ni/ZSM-5) at the condition of T=400℃, WHSV=4 h-1. The catalysts physical properties were investigated by BET (Brunauer-Emmett-Teller surface area) analyse. Water content was detected by using the method of Karl Fischer (870 KF Titrino). The GC-MS was used to analyze the major constituents of the pyrolytic products qualitatively and quantitatively. After the addition of La, the pore size increased from 0.61 nm (ZSM-5) to 0.89 nm (La-ZSM-5). On the contrary, the pore size of P modified ZSM-5 is 0.49 nm which is smaller than that of ZSM-5. The pyrolytic products of the model compounds included organic fraction, water, coke and gas. Compared with ZSM-5,the coke deposition over the La modified ZSM-5 decreased from 2.61% to 1.99% and the organic fraction increased dramatically from 46.10% to 61.51%, which showed the best performance in terms of products distribution among all modified catalyst. The conversions of overall model components and single model component were calculated respectively. The difficulty of the model components pyrolysis is guaiacol>furfural>ethyl acetate>diacetone alcohol. By adding catalysts, the conversion of totally compounds were increased in different degrees, which meaned zeolite promoted the degree of catalytic pyrolysis. HZSM-5 had a best catalytic pyrolysis activity with the highest totally compounds conversion rate of 65.98%. There was a slight decline in the conversion of model compounds contrasted ZSM-5 with La/P/Ni modified ZSM-5. The major components of catalytic pyrolysis were aromatic hydrocarbons, ketones, phenols and so on. It means that a series of decarboxylation and decarbonylation reactions were taken place during the pyrolysis process. On the one hand, the reduction of the oxygen content of bio-oil help to improve its stability, on the other hand it will enhance its heating value. The optimal selectivity of aromatic reached 7.36% over HZSM-5. The La modified ZSM-5 improved the selectivity of aromatic from 6.72%to 7.28%. The highest yield of saturated alcohol was 7.1%over ZSM-5 and decreased using modified ZSM-5. According to the catalytic pyrolysis products distribution, the different reaction pathways for model compounds were discussed, which provided a theoretical basis for experimental study of upgrading bio-oil.

Cascaded Catalytic Copyrolysis of Microalgae and LDPE with Ni/Biochar and HZSM-5 for Improving High-Grade Bio-Oil Production

Co-hydrotreating of Algae and Used Engine Oil for the Direct Production of Gasoline and Diesel Fuels or Blending Components

Catalytic Pyrolysis of Microalgae for Production of Aromatics and Ammonia

Catalytic pyrolysis of bio-oil model compounds over La/P/Ni modified ZSM-5

Production of catalytic-upgraded pyrolysis products from oiltea camellia shell and polypropylene using NiCe-X/Al2O3 and ZrO2 catalyst (X = Fe, Co)

Effect of Novel Ni2P-loaded Catalysts on Algal Pyrolysis Bio-Oil

In-depth Study of Synergism Between Torrefaction and Catalyst for Balanced Production of Bio-Oil from Rice Husk Pyrolysis Based on Hydrocarbons Production, Energy Yield and Deoxygenation Degree

Characterization and mechanism elucidation of high-quality bio-oil production from co-pyrolysis of waste low-rank coal fines and de-oiled microalgae biomass using bimetallic (Cu-Cr) ZSM-5 catalyst

Catalytic co-pyrolysis of rice straw and ulva prolifera macroalgae: Effects of process parameter on bio-oil up-gradation

A novel three-stage ex-situ catalytic pyrolysis process for improved bio-oil yield and quality from lignocellulosic biomass

RETRACTED: Catalytic Co-Pyrolysis of Rice Straw and Ulva Prolifera Macroalgae: Effects of Process Parameter on Bio-Oil Up-Gradation

Improving bio-oil quality from low-density polyethylene pyrolysis: Effects of varying activation and pyrolysis parameters

Catalytic copyrolysis of metal impregnated biomass and plastic with Ni‐based HZSM‐5 catalyst: Synergistic effects, kinetics and product distribution

Accelerating the production of bio-oil from hydrothermal liquefaction of microalgae via recycled biochar-supported catalysts

Catalytic co‐pyrolysis of macroalgal components with lignocellulosic biomass for enhanced biofuels and high‐valued chemicals

Ni dopped MgAl hydrotalcite catalyzed hydrothermal liquefaction of microalgae for low N, O bio-oil production

Enhancing Hydrodeoxygenation of Bio-oil via Bimetallic Ni-V Catalysts Modified by Cross-Surface Migrated-Carbon from Biochar

Catalytic fast co-pyrolysis of Douglas Fir and low-density polyethylene with nanocellulose-derived carbon catalyst for enhancing selectivity of hydrogen in syngas and mono-aromatic hydrocarbon in bio-oil products

Co-pyrolysis of microalgae and other biomass wastes for the production of high-quality bio-oil: Progress and prospective

Selective production of high-value fuel via catalytic upgrading of bio-oil over nitrogen-doped carbon-alumina hybrid supported cobalt catalysts

Synergistic effects of catalytic co-pyrolysis of macroalgae with waste plastics